Estudo do equilíbrio líquido-líquido e da estabilidade de sistemas envolvendo biodiesel, álcoois e água

O estudo da estabilidade de emulsões de biocombustíveis destaca-se, dentre outros aspectos, pela necessidade de identificação das características destas. Esta necessidade reforça-se pela dificuldade de detecção de biodiesel e suas misturas quando estão fora de especificação, além de se aplicar aos processos de separação e purificação do biodiesel após a transesterificação. O entendimento deste problema poderá ser alcançado a partir de estudos de estabilidade associados aos modelos termodinâmicos de equilíbrio líquido-líquido (modelo NRTL) em sistemas ternários, que serão a base da modelagem proposta neste trabalho. O levantamento de dados envolve técnicas de observação direta em titulação, e ensaios de estabilidade e tensiometria, com algumas alterações das técnicas clássicas. Desta forma, o objetivo principal do trabalho é propor uma maneira de identificar e caracterizar as interfaces das emulsões formadas e estudar a estabilidade das fases envolvidas. Além disso, estuda-se a introdução de alcoóis como agentes tensoativos para viabilizar a utilização de misturas de combustíveis, mesmo na região de mais de uma fase. Para o desenvolvimento do trabalho, emulsões envolvendo os constituintes básicos serão combinadas entre si em diferentes proporções. A etapa inicial constitui-se de um mapeamento das misturas e proporções que formam as emulsões, baseadas nas curvas de equilíbrio. Em seguida, faz-se o estudo de caracterização e estabilidade destes sistemas. Com estas informações é possível mapear o sentido de incremento de tensão na interface e instabilidade da separação de fases das emulsões em relação aos diagramas ternários correspondentes. Por fim, propõe-se uma estratégia para estimar os parâmetros termodinâmicos do NRTL para as espécies presentes nos sistemas estudados e prever o comportamento dos mesmos e de sistemas similares. Este modelo matemático proposto tem como objetivo complementar a técnica experimental adotada para construção das curvas de equilíbrio, sendo bem sucedido

Efeitos da transferência de massa na relação matemática entre espessuras real e aparente em fase livre de gasolina com etanol nas contaminações subterrâneas

Esta tese trata da relação matemática entre as espessuras real e aparente em contaminações subterrâneas com gasolina e com gasolina e etanol. Foi testada a hipótese de que a relação entre as espessuras dos dois tipos de gasolinas pode ser descrita pela mesma relação matemática desde que esta relação incorpore as tensões interfaciais entre a água e a gasolina e gasolina e o ar que ocorrem no meio poroso. É proposta uma relação matemática hidrostática para o equilíbrio considerando o contato entre o poço de monitoramento e o meio poroso e a tensão interfacial responsável pelos efeitos capilares no meio poroso e a densidade dos fluidos. Os experimentos conduzidos em meio poroso e colunas acrílicas mostraram um ajuste estatisticamente melhor da equação matemática proposta para a gasolina pura e um ajuste que apresentou menor representatividade estatística para a gasolina com etanol. Esta discrepância está relacionada ao fato da transferência de massa do etanol presente na gasolina para a água não ser um fenômeno desprezível, causar grande influência no sistema e não estar contemplada na relação matemática proposta. Outro fenômeno observado em gotas de fluidos em experimentos para medir a tensão interfacial pode ser responsável pelo ajuste menos representativo da equação que é a presença de instabilidades na interface de contato entre a gasolina e a água. Estas instabilidades que são chamadas na literatura de Efeito Marangoni produzem variações na interface entre água e gasolina e são também responsáveis pela diferença no ajuste da equação.

Efeito da perda de carga e calor no poço injetor no processo de drenagem gravitacional assistido com vapor e solvente

Nowadays, most of the hydrocarbon reserves in the world are in the form of heavy oil, ultra - heavy or bitumen. For the extraction and production of this resource is required to implement new technologies. One of the promising processes for the recovery of this oil is the Expanding Solvent Steam Assisted Gravity Drainage (ES-SAGD) which uses two parallel horizontal wells, where the injection well is situated vertically above the production well. The completion of the process occurs upon injection of a hydrocarbon additive at low concentration in conjunction with steam. The steam adds heat to reduce the viscosity of the oil and solvent aids in reducing the interfacial tension between oil/ solvent. The main force acting in this process is the gravitational and the heat transfer takes place by conduction, convection and latent heat of steam. In this study was used the discretized wellbore model, where the well is discretized in the same way that the reservoir and each section of the well treated as a block of grid, with interblock connection with the reservoir. This study aims to analyze the influence of the pressure drop and heat along the injection well in the ES-SAGD process. The model used for the study is a homogeneous reservoir, semi synthetic with characteristics of the Brazilian Northeast and numerical simulations were performed using the STARS thermal simulator from CMG (Computer Modelling Group). The operational parameters analyzed were: percentage of solvent injected, the flow of steam injection, vertical distance between the wells and steam quality. All of them were significant in oil recovery factor positively influencing this. The results showed that, for all cases analyzed, the model considers the pressure drop has cumulative production of oil below its respective model that disregards such loss. This difference is more pronounced the lower the value of the flow of steam injection

Desenvolvimento de sistemas a base de tensoativos para recuperação avançada de petróleo

Petroleum is a complex combination of various classes of hydrocarbons, with paraffinic, naphtenic and aromatic compounds being those more commonly found in its composition. The recent changes in the world scenario, the large reserves of heavy oils and also the lack of new discoveries of large petroleum fields are indications that, in the near future, the oil recovery by conventional methods will be limited. In order to increase the efficiency of the extraction process, enhanced recovery methods are cited in applications where conventional techniques have proven to be little effective. The injection of surfactant solutions as an enhanced recovery method is advantageous in that surfactants are able to reduce the interfacial tensions between water and oil, thus augmenting the displacement efficiency and, as a consequence, increasing the recovery factor. This work aims to investigate the effects of some parameters that influence the surfactant behavior in solution, namely the type of surfactant, the critical micelle concentration (CMC) and the surface and interface tensions between fluids. Seawater solutions containing the surfactants PAN, PHN and PJN have been prepared for presenting lower interfacial tensions with petroleum and higher stability under increasing temperature and salinity. They were examined in an experimental apparatus designed to assess the recovery factor. Botucatu (Brazil) sandstone plug samples were submitted to assay steps comprising saturation with seawater and petroleum, conventional recovery with seawater and enhanced recovery with surfactant solutions. The plugs had porosity between 29.6 and 32.0%, with average effective permeability to water of 83 mD. The PJN surfactant, at a concentration 1000% above CMC in water, had a higher recovery factor, causing the original oil in place to be recovered by an extra 20.97%, after conventional recovery with seawater

Remoção de óleo da água de produção por flotação em coluna utilizando tensoativos de origem vegetal

In the petroleum industry, water is always present in the reservoir formation together with petroleum and natural gas and this fact provokes the production of water with petroleum, resulting in a great environmental impact. Several methods can be applied for treatment of oily waters, such as: gravitational vases, granulated media filtration systems, flotation process, centrifugation process and the use of hydrocyclones, which can also be used in a combined way. However, the flotation process has showed a great efficiency as compared with other methods, because these methods do not remove great part of the emulsified oil. In this work was investigated the use of surfactants derived from vegetable oils, OSS and OGS, as collectors, using the flotation process in a glass column with a porous plate filter in its base for the input of the gaseous steam. For this purpose, oil/water emulsions were prepared using mechanical stirring, with concentrations around 300 ppm. The air flow rate was set at 700 cm3/min and the porous plate filter used for the generation of the air bubbles has pore size varying from 16 to 40 Pm. The column operated at constant volume (1500mL). A new methodology has been developed to collect the samples, where, instead of collecting the water phase, it was collected the oil phase removed by the process in the top of the flotation column. It has been observed that it is necessary to find an optimum surfactant concentration to achieve enhanced removal efficiency. Being for OSS 1.275 mmol/L and for OGS 0.840 mmol/L, with removal efficiencies of 93% and 99%, respectively, using synthetic solutions. For the produced water, the removal in these concentrations was 75% for OSS and 65% for OGS. It is possible to remove oil from water in a flotation process using surfactants of high HLB, fact that is against the own definition of HLB (Hydrophile-Lipophile Balance). The interfacial tension is an important factor in the oil removal process using a flotation process, because it has direct interference in the coalescence of the oil drops. The spreading of the oil of the air bubble should be considered in the process, and for the optimum surfactant concentrations it reached a maximum value. The removal kinetics for the flotation process using surfactants in the optimum concentration has been adjusted according to a first order model, for synthetic water as for the produced water.

Estudo de uma coluna de absorção recheada para desidratação do gás natural utilizando microemulsão como absorvente

During natural gas processing, water removal is considered as a fundamental step in that combination of hydrocarbons and water favors the formation of hydrates. The gas produced in the Potiguar Basin (Brazil) presents high water content (approximately 15000 ppm) and its dehydration is achieved via absorption and adsorption operations. This process is carried out at the Gas Treatment Unit (GTU) in Guamaré (GMR), in the State of Rio Grande do Norte. However, it is a costly process, which does not provide satisfactory results when water contents as low as 0.5 ppm are required as the exit of the GTU. In view of this, microemulsions research is regarded as an alternative to natural gas dehydration activities. Microemulsions can be used as desiccant fluids because of their unique proprieties, namely solubilization enhancement, reduction in interfacial tensions and large interfacial area between continuous and dispersed phases. These are actually important parameters to ensure the efficiency of an absorption column. In this work, the formulation of the desiccant fluid was determined via phases diagram construction, employing there nonionic surfactants (RDG 60, UNTL L60 and AMD 60) and a nonpolar fluid provided by Petrobras GMR (Brazil) typically comprising low-molecular weight liquid hydrocarbons ( a solvent commonly know as aguarrás ). From the array of phases diagrams built, four representative formulations have been selected for providing better results: 30% RDG 60-70% aguarrás; 15% RDG 60-15% AMD 60-70% aguarrás, 30% UNTL L60-70% aguarrás, 15% UNTL L60-15% AMD 60-70% aguarrás. Since commercial natural gas is already processed, and therefore dehydrated, it was necessary to moister some sample prior to all assays. It was then allowed to cool down to 13ºC and interacted with wet 8-12 mesh 4A molecular sieve, thus enabling the generation of gas samples with water content (approximately 15000 ppm). The determination of the equilibrium curves was performed based on the dynamic method, which stagnated liquid phase and gas phase at a flow rate of 200 mL min-1. The hydrodynamic study was done with the aim of established the pressure drop and dynamic liquid hold-up. This investigation allowed are to set the working flow rates at 840 mL min-1 for the gas phase and 600 mLmin-1 for the liquid phase. The mass transfer study indicated that the system formed by UNTL L60- turpentine-natural gas the highest value of NUT

Síntese e caracterização de tensoativos e estudo de equilíbrio de fase dos sistemas CnH2n+2/H2O/CnH2n+1COONa/But-OH

The growing utilization of surfactants in several different areas of industry has led to an increase on the studies involving solutions containing this type of molecules. Due to its amphiphilic nature, its molecule presents one polar part and one nonpolar end, which easily interacts with other molecules, being able to modify the media properties. When the concentration in which its monomers are saturated, the airliquid system interface is reached, causing a decrease in interfacial tension. The surfactants from pure fatty acids containing C8, C12 and C16 carbonic chains were synthesized in an alcoholic media using sodium hydroxide. They were characterized via thermal analysis (DTA and DTG) and via infrared spectroscopy, with the intention of observing their purity. Physical and chemical properties such as superficial tension, critical micelle concentration (c.m.c), surfactant excess on surface and Gibbs free energy of micellization were determined in order to understand the behaviour of these molecules with an aqueous media. Pseudo-ternary phase diagrams were obtained aiming to limit the Windsor equilibria conditions so it could be possible to understand how the surfactants carbonic chain size contributes to the microemulsion region. Solutions with known concentrations were prepared to study how the surfactants can influence the dynamic light scattering spectroscopy (DLS) and how the diffusion coefficient is influenced when the media concentration is altered. The results showed the variation on the chain size of the studied surfactant lipophilic part allows the conception of surfactants with similar interfacial properties, but dependent on the size of the lipophilic part of the surfactant. This variation causes the surfactant to have less tendency of microemulsionate oil in water. Another observed result is that the n-alcanes molecule size promoted a decrease on the microemulsion region on the obtained phase diagrams

Microemulsão: Um promissor carreador para moléculas insolúveis

Microemulsions (ME) are thermodynamically stable and isotropic systems of two immiscible liquids (oil/water), stabilized by an interfacial film of surfactants, discovered by Hoar and Schulman in 1943. The study of ME formation is based on three areas of theory: (1) solubilization, (2) interfacial tension and (3) thermodynamics. ME structures are influenced by the physicochemical properties and proportions of their ingredients. The goal of this review is to assess the state of the art of microemulsified systems, from a theoretical viewpoint. Also, recent progress on their clinical application and use as carriers for insoluble compounds is discussed.

Correlação entre estrutura e propriedades de sistemas líquidos cristalinos para a liberação prolongada de fármacos

Pós-graduação em Ciências Farmacêuticas - FCFAR

Produção de biossurfactantes pelos fungos Aspergillus ochraceus e Penicillium expansum em fermentação semi-sólida utilizando resíduos agroindustriais como substrato

Pós-graduação em Microbiologia - IBILCE

Desenvolvimento de estratégias de alimentação para produção de ramnolipídios por Pseudomonas aeruginosa LBI 2A1 em biorreator

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Potencial biotecnológico de rizóbios como bioemulsificante e biossorvente de cobre e cromo

Pós-graduação em Microbiologia Agropecuária - FCAV

Relationship between composition and organizational levels of nanostructured systems formed by Oleth 10 and PPG-5-Ceteth-20 for potential drug delivery

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito da perda de carga e calor no poço injetor no processo de drenagem gravitacional assistido com vapor e solvente

Nowadays, most of the hydrocarbon reserves in the world are in the form of heavy oil, ultra - heavy or bitumen. For the extraction and production of this resource is required to implement new technologies. One of the promising processes for the recovery of this oil is the Expanding Solvent Steam Assisted Gravity Drainage (ES-SAGD) which uses two parallel horizontal wells, where the injection well is situated vertically above the production well. The completion of the process occurs upon injection of a hydrocarbon additive at low concentration in conjunction with steam. The steam adds heat to reduce the viscosity of the oil and solvent aids in reducing the interfacial tension between oil/ solvent. The main force acting in this process is the gravitational and the heat transfer takes place by conduction, convection and latent heat of steam. In this study was used the discretized wellbore model, where the well is discretized in the same way that the reservoir and each section of the well treated as a block of grid, with interblock connection with the reservoir. This study aims to analyze the influence of the pressure drop and heat along the injection well in the ES-SAGD process. The model used for the study is a homogeneous reservoir, semi synthetic with characteristics of the Brazilian Northeast and numerical simulations were performed using the STARS thermal simulator from CMG (Computer Modelling Group). The operational parameters analyzed were: percentage of solvent injected, the flow of steam injection, vertical distance between the wells and steam quality. All of them were significant in oil recovery factor positively influencing this. The results showed that, for all cases analyzed, the model considers the pressure drop has cumulative production of oil below its respective model that disregards such loss. This difference is more pronounced the lower the value of the flow of steam injection