Potential for broad range multiplexing of fibre Bragg gratings in polymer optical fibres and operation in the 700-nm wavelength range

Refractive index and structural characteristics of optical polymers are strongly influenced by the thermal history of the material. Polymer optical fibres (POF) are drawn under tension, resulting in axial orientation of the polymer molecular chains due to their susceptibility to align in the fibre direction. This change in orientation from the drawing process results in residual strain in the fibre and also affects the transparency and birefringence of the material (1-3). PMMA POF has failure strain as high as over 100%. POF has to be drawn under low tension to achieve this value. The drawing tension affects the magnitude of molecular alignment along the fibre axis, thus affecting the failure strain. The higher the tension the lower the failure stain will be. However, the properties of fibre drawn under high tension can approach that of fibre drawn under low tension by means of an annealing process. Annealing the fibre can generally optimise the performance of POF while keeping most advantages intact. Annealing procedures can reduce index difference throughout the bulk and also reduce residual stress that may cause fracture or distortion. POF can be annealed at temperatures approaching the glass transition temperature (Tg) of the polymer to produce FBG with a permanent blue Bragg wave-length shift at room temperature. At this elevated temperature segmental motion in the structure results in a lower viscosity. The material softens and the molecular chains relax from the axial orientation causing shrinking of the fibre. The large attenuation of typically 1dB/cm in the 1550nm spectral region of PMMA POF has limited FBG lengths to less than 10cm. The more expensive fluorinated polymers with lower absorption have had no success as FBG waveguides. Bragg grating have been inscribed onto various POF in the 800nm spectral region using a 30mW continuous wave 325nm helium cadmium laser, with a much reduced attenuation coefficient of 10dB/m (5). Fabricating multiplexed FBGs in the 800nm spectral region in TOPAS and PMMA POF consistently has lead to fabrication of multiplexed FBG in the 700nm spectral region by a method of prolonged annealing. The Bragg wavelength shift of gratings fabricated in PMMA fibre at 833nm and 867nm was monitored whilst the POF was thermally annealed at 80°C. Permanent shifts exceeding 80nm into the 700nm spectral region was attained by both gratings on the fibre. The large permanent shift creates the possibility of multiplexed Bragg sensors operating over a broad range. -------------------------------------------------------------------------------------------------------------------- 1. Pellerin C, Prud'homme RE, Pézolet M. Effect of thermal history on the molecular orientation in polystyrene/poly (vinyl methyl ether) blends. Polymer. 2003;44(11):3291-7. 2. Dvoránek L, Machová L, Šorm M, Pelzbauer Z, Švantner J, Kubánek V. Effects of drawing conditions on the properties of optical fibers made from polystyrene and poly (methyl methacrylate). Die Angewandte Makromolekulare Chemie. 1990;174(1):25-39. 3. Dugas J, Pierrejean I, Farenc J, Peichot JP. Birefringence and internal stress in polystyrene optical fibers. Applied optics. 1994;33(16):3545-8. 4. Jiang C, Kuzyk MG, Ding JL, Johns WE, Welker DJ. Fabrication and mechanical behavior of dye-doped polymer optical fiber. Journal of applied physics. 2002;92(1):4-12. 5. Johnson IP, Webb DJ, Kalli K, Yuan W, Stefani A, Nielsen K, et al., editors. Polymer PCF Bragg grating sensors based on poly (methyl methacrylate) and TOPAS cyclic olefin copolymer2011: SPIE.

Potential for broad range multiplexing of fibre Bragg gratings in polymer optical fibres and operation in the 700-nm wavelength range

Refractive index and structural characteristics of optical polymers are strongly influenced by the thermal history of the material. Polymer optical fibres (POF) are drawn under tension, resulting in axial orientation of the polymer molecular chains due to their susceptibility to align in the fibre direction. This change in orientation from the drawing process results in residual strain in the fibre and also affects the transparency and birefringence of the material (1-3). PMMA POF has failure strain as high as over 100%. POF has to be drawn under low tension to achieve this value. The drawing tension affects the magnitude of molecular alignment along the fibre axis, thus affecting the failure strain. The higher the tension the lower the failure stain will be. However, the properties of fibre drawn under high tension can approach that of fibre drawn under low tension by means of an annealing process. Annealing the fibre can generally optimise the performance of POF while keeping most advantages intact. Annealing procedures can reduce index difference throughout the bulk and also reduce residual stress that may cause fracture or distortion. POF can be annealed at temperatures approaching the glass transition temperature (Tg) of the polymer to produce FBG with a permanent blue Bragg wave-length shift at room temperature. At this elevated temperature segmental motion in the structure results in a lower viscosity. The material softens and the molecular chains relax from the axial orientation causing shrinking of the fibre. The large attenuation of typically 1dB/cm in the 1550nm spectral region of PMMA POF has limited FBG lengths to less than 10cm. The more expensive fluorinated polymers with lower absorption have had no success as FBG waveguides. Bragg grating have been inscribed onto various POF in the 800nm spectral region using a 30mW continuous wave 325nm helium cadmium laser, with a much reduced attenuation coefficient of 10dB/m (5). Fabricating multiplexed FBGs in the 800nm spectral region in TOPAS and PMMA POF consistently has lead to fabrication of multiplexed FBG in the 700nm spectral region by a method of prolonged annealing. The Bragg wavelength shift of gratings fabricated in PMMA fibre at 833nm and 867nm was monitored whilst the POF was thermally annealed at 80°C. Permanent shifts exceeding 80nm into the 700nm spectral region was attained by both gratings on the fibre. The large permanent shift creates the possibility of multiplexed Bragg sensors operating over a broad range. -------------------------------------------------------------------------------------------------------------------- 1. Pellerin C, Prud'homme RE, Pézolet M. Effect of thermal history on the molecular orientation in polystyrene/poly (vinyl methyl ether) blends. Polymer. 2003;44(11):3291-7. 2. Dvoránek L, Machová L, Šorm M, Pelzbauer Z, Švantner J, Kubánek V. Effects of drawing conditions on the properties of optical fibers made from polystyrene and poly (methyl methacrylate). Die Angewandte Makromolekulare Chemie. 1990;174(1):25-39. 3. Dugas J, Pierrejean I, Farenc J, Peichot JP. Birefringence and internal stress in polystyrene optical fibers. Applied optics. 1994;33(16):3545-8. 4. Jiang C, Kuzyk MG, Ding JL, Johns WE, Welker DJ. Fabrication and mechanical behavior of dye-doped polymer optical fiber. Journal of applied physics. 2002;92(1):4-12. 5. Johnson IP, Webb DJ, Kalli K, Yuan W, Stefani A, Nielsen K, et al., editors. Polymer PCF Bragg grating sensors based on poly (methyl methacrylate) and TOPAS cyclic olefin copolymer2011: SPIE.

Physical and biological properties of a novel siloxane adhesive for soft tissue applications

The aim of this study was to investigate the adhesive properties of an in-house amino-propyltrimethoxysilane-methylenebisacrylamide (APTMS-MBA) siloxane system and compare them with a commercially available adhesive, n-butyl cyanoacrylate (nBCA). The ability of the material to perform as a soft tissue adhesive was established by measuring the physical (bond strength, curing time) and biological (cytotoxicity) properties of the adhesives on cartilage. Complementary physical techniques, X-ray photoelectron spectroscopy, Raman and infrared imaging, enabled the mode of action of the adhesive to the cartilage surface to be determined. Adhesion strength to cartilage was measured using a simple butt joint test after storage in phosphate-buffered saline solution at 37°C for periods up to 1 month. The adhesives were also characterised using two in vitro biological techniques. A live/dead stain assay enabled a measure of the viability of chondrocytes attached to the two adhesives to be made. A water-soluble tetrazolium assay was carried out using two different cell types, human dermal fibroblasts and ovine meniscal chondrocytes, in order to measure material cytotoxicity as a function of both supernatant concentration and time. IR imaging of the surface of cartilage treated with APTMS-MBA siloxane adhesive indicated that the adhesive penetrated the tissue surface marginally compared to nBCA which showed a greater depth of penetration. The curing time and adhesion strength values for APTMS-MBA siloxane and nBCA adhesives were measured to be 60 s/0.23 MPa and 38 min/0.62 MPa, respectively. These materials were found to be significantly stronger than either commercially available fibrin (0.02 MPa) or gelatin resorcinol formaldehyde (GRF) adhesives (0.1 MPa) (P <0.01). Cell culture experiments revealed that APTMS-MBA siloxane adhesive induced 2% cell death compared to 95% for the nBCA adhesive, which extended to a depth of approximately 100-150 μm into the cartilage surface. The WST-1 assay demonstrated that APTMS-MBA siloxane was significantly less cytotoxic than nBCA adhesive as an undiluted conditioned supernatant (P <0.001). These results suggest that the APTMS-MBA siloxane may be a useful adhesive for medical applications. © VSP 2005.

New oil modified acrylic polymer for pH sensitive drug release:experimental results and statistical analysis

We report results of an experimental study, complemented by detailed statistical analysis of the experimental data, on the development of a more effective control method of drug delivery using a pH sensitive acrylic polymer. New copolymers based on acrylic acid and fatty acid are constructed from dodecyl castor oil and a tercopolymer based on methyl methacrylate, acrylic acid and acryl amide were prepared using this new approach. Water swelling characteristics of fatty acid, acrylic acid copolymer and tercopolymer respectively in acid and alkali solutions have been studied by a step-change method. The antibiotic drug cephalosporin and paracetamol have also been incorporated into the polymer blend through dissolution with the release of the antibiotic drug being evaluated in bacterial stain media and buffer solution. Our results show that the rate of release of paracetamol getss affected by the pH factor and also by the nature of polymer blend. Our experimental data have later been statistically analyzed to quantify the precise nature of polymer decay rates on the pH density of the relevant polymer solvents. The time evolution of the polymer decay rates indicate a marked transition from a linear to a strictly non-linear regime depending on the whether the chosen sample is a general copolymer (linear) or a tercopolymer (non-linear). Non-linear data extrapolation techniques have been used to make probabilistic predictions about the variation in weight percentages of retained polymers at all future times, thereby quantifying the degree of efficacy of the new method of drug delivery.

Exploring the biological basis for Salmonella persistence in food manufacturing environments

The persistence of Salmonella spp. in low moisture foods is a challenge for the food industry as despite control strategies already in place, notable outbreaks still occur. The aim of this study was to characterise isolates of Salmonella, known to be persistent in the food manufacturing environment, by comparing their microbiological characteristics with a panel of matched clinical and veterinary isolates. The gross morphology of the challenge panel was phenotypically characterised in terms of cellular size, shape and motility. In all the parameters measured, the factory isolates were indistinguishable from the human, clinical and veterinary strains. Further detailed metabolic profiling was undertaken using the biolog Microbial ID system. Multivariate analysis of the metabolic microarray revealed differences in metabolism of the factory isolate of S.Montevideo, based on its upregulated ability to utilise glucose and the sugar alcohol groups. The remainder of the serotype-matched isolates were metabolically indistinguishable. Temperature and humidity are known to influence bacterial survival and through environmental monitoring experimental parameters were defined. The results revealed Salmonella survival on stainless steel was affected by environmental temperatures that may be experienced in a food processing environment; with higher survival rates (D25=35.4) at temperatures at 25°C and lower humidity levels of 15% RH, however a rapid decline in cell count (D10=3.4) with lower temperatures of 10°C and higher humidity of 70% RH. Several resident factories strains survived in higher numbers on stainless steel (D25=29.69) compared to serotype matched clinical and veterinary isolates (D25=22.98). Factory isolates of Salmonella did not show an enhanced growth rate in comparison to serotype matched solates grown in Luria broth, Nutrient broth and M9 minimal media indicating that as an independent factor, growth was unlikely to be a major factor driving Salmonella persistence. Using a live / dead stain coupled with fluorescence microscopy revealed that when no longer culturable, isolates of S.Schwarzengrund entered into a viable nonculturable state. The biofilm forming capacity of the panel was characterised and revealed that all were able to form biofilms. None of the factory isolates showed an enhanced capability to form biofilms in comparison to serotype-matched isolates. In disinfection studies, planktonic cells were more susceptible to disinfectants than cells in biofilm and all the disinfectants tested were successful in reducing bacterial load. Contact time was one of the most important factors for reducing bacterial populations in a biofilm. The genomes of eight strains were sequenced. At the nucleotide and amino acid level the food factory isolates were similar to those of isolates from other environments; no major genomic rearrangements were observed, supporting the conclusions of the phenotypic and metabolic analysis. In conclusion, having investigated a variety of morphological, biochemical and genomic factors, it is unlikely that the persistence of Salmonella in the food manufacturing environment is attributable to a single phenotypic, metabolic or genomic factor. Whilst a combination of microbiological factors may be involved it is also possible that strain persistence in the factory environment is a consequence of failure to apply established hygiene management principles.

The effect of disfiguring features on covert and overt attention to faces

It is well documented that facial disfigurements can generate avoidance responses in observers towards the afflicted person, yet less is known about the effect of a facial disfigurement on attention to and perception of faces. In two experiments we studied overt and covert attention to laterally presented face stimuli when these contained a unilateral disfiguring feature (a simulated portwine stain), an occluding feature, or no salient feature. In Experiment 1, observers’ eye movements were tracked while they explored laterally presented faces which they had to rate for attractiveness. Overt attention, as measured by the patterns of fixations on the face, was found to be significantly affected by the presence of a facial disfigurement or an occluder. In Experiment2, we used a covert orienting task with bilaterally presented target and distractor to measure the interference effect induced by a distractor face (disfigured, occluded, or normal) on a non facetarget discrimination task. The presence of a face increased response times to the target stimulus,but this interference was not modulated by the presence of a salient feature (disfigurement or occluder). Together, these results suggest that the presence of salient features affect overt but not the covert processing of faces.

Optimizing the Synthesis of AZN

Azulenyl nitrone (AZN) is a bright green compound that can be used to stain different compounds, including plastics. When these stained plastics are irradiated, as they commonly are in the sterilization of medical devices, AZN changes color from green to red, constituting a permanent change. This would make obsolete the current methods of radioactive labeling and maintain the integrity of medical equipment. Although a method of synthesis is already in place, the aim was to improve the yield significantly and find a more efficient and cost-effective procedure. Last year, the procedure used resulted in 18 to 20% of AZN synthesized at the most favorable conditions. With that in mind, this year modifications were done in the hopes of improving the yield. The solvent was changed to a mixture of isopropanol and triethylamine, a stronger base, and a catalytic amount of N-tertbutyl hydroxylamine hydrochloride was used (around 4 equivalents). The reaction time was also increased to 7 days, rather than 2. After several trials, the samples were run through column chromatography and the average yield was 70%, a much more promising result than that obtained last year. There is still research to be done to improve the technicalities of the procedure, including altering the amounts of N-tertbutyl hydroxylamine hydrochloride to try and obtain similar data with fewer amounts. This portion of the research will be done in the second half of the year. In the meantime, however, a novel and more efficient method of synthesis has been established for the production of AZN that can be potentially commercialized.

Optimizing the Synthesis of AZN

Azulenyl nitrone (AZN) is a bright green compound that can be used to stain different compounds, including plastics. When these stained plastics are irradiated, as they commonly are in the sterilization of medical devices, AZN changes color from green to red, constituting a permanent change. This would make obsolete the current methods of radioactive labeling and maintain the integrity of medical equipment. Although a method of synthesis is already in place, the aim was to improve the yield significantly and find a more efficient and cost-effective procedure. Last year, the procedure used resulted in 18 to 20% of AZN synthesized at the most favorable conditions. With that in mind, this year modifications were done in the hopes of improving the yield. The solvent was changed to a mixture of isopropanol and triethylamine, a stronger base, and a catalytic amount of N-tertbutyl hydroxylamine hydrochloride was used (around 4 equivalents). The reaction time was also increased to 7 days, rather than 2. After several trials, the samples were run through column chromatography and the average yield was 70%, a much more promising result than that obtained last year. There is still research to be done to improve the technicalities of the procedure, including altering the amounts of N-tertbutyl hydroxylamine hydrochloride to try and obtain similar data with fewer amounts. This portion of the research will be done in the second half of the year. In the meantime, however, a novel and more efficient method of synthesis has been established for the production of AZN that can be potentially commercialized.

Física do meio ambiente como disciplina nas licenciaturas em física: proposta de uma unidade didática para ensinar efeito estufa e aquecimento global

In this dissertation we propose a Teaching Unit of Physics to teach content through environmental discussions of the greenhouse effect and global warming. This teaching unit is based on a problem-methodological intervention from the application of the method of the Arch of Charles Maguerez. The methodological foundations of the thesis are embedded in action research and this is structured in five chapters: the first chapter deals with the Physical Environment (FMA) as a subject in Degree Courses in Physics in Brazil, bringing the concern of how this discipline has been taught. We started the first chapter explaining the reasons behind the inclusion of the discipline of Physical Environment in a Physics Degree Courses. Then we did a search on the websites of Institutions of Higher Education, to know of the existence or not of this discipline on curricular. We then analyzed the menus to see what bibliographies are being adopted and what content of Physics are being worked, and how it has been done. The courses surveyed were those of Federal and Federal Institutes Universities. Thus ended the first chapter. Given the inseparability between studies in Physics Teaching and studies on competencies, skills and significant learning, wrote the second chapter. In this chapter we discuss the challenge of converting information into knowledge. Initially on initial teacher training, because even if this is not our focus, the study is a discipline on the upper reaches, therefore, offered to future teachers. Then we talked about the culture of knowledge, where we emphasize the use of a teaching approach that promotes meanings taught by content and make sense to the student. We finished the third chapter, making some considerations on skills and abilities, in order to identify what skills and competencies were developed and worked during and after the implementation of Curriculum Unit. The third chapter is the result of a literature review and study of the radioactive EarthSun interaction. The subjects researched approach from the generation of energy in the sun to topics stain solar coronal mass ejections, solar wind, black body radiation, Wien displacement law, Stefan-Boltzmann Law, greenhouse effect and global warming. This chapter deals with material support for the teacher of the aforementioned discipline. The fourth chapter talks about the arc method of Charles Maguerez; Here we explain the structure of each of the five steps of the Arc and how to use them in teaching. We also show another version of this method adapted by Bordenave. In the fifth and final chapter brought a description of how the method of Arc was used in physics classes of Environment, with students majoring in Physics IFRN Campus Santa Cruz. Here, in this chapter, a transcript of classes to show how was the application of a problem-based methodology in the teaching of content proposed for Physics Teaching Unit from the environmental discussion about the greenhouse effect and global warming phenomena

Conservação de material genético de espécies silvestres do bioma caatinga utilizando a manipulação oócitos inclusos em folículos ovarianos pré antrais (MOIFOPA)

The objective of the present thesis was to use the manipulation of oocytes enclosed in preantral follicles (MOEPF) as a tool for the female gametes rescue and optimization, from wild species of Caatinga biome. The thesis was divided into 4 experiments. At first experiment, it was performed the estimative and description of the agouti (Dasyprocta leporina) preantral follicles (PF) histologic and ultrastructural features, in which it was estimated 4419.8 ± 532.26 and 5397.52 ± 574.91 follicles for the right and left ovary, respectively, and the majority (86,63%) belonged to the primordial follicles category (P<0.05). Most of the population consists of morphologically normal follicles (70.78%), presenting a large and central nuclei and uniform cytoplasm. At ultrastructural evaluation it was verified the presence of a great number of round mitochondrias associated to lipid droplets. In the second experiment, it was performed the estimative and description of yellow-toothed cavies (Galea spixii) PF characteristics, also, the evaluation of the effect of solid surface vitrification (SSV) on the in situ PF morphology. The total of 416.0 ± 342.8 PF was estimated for the ovary pair and the presence of a large quantity of primary follicles (P<0.05) was evidenced. Most of the PF was morphologically normal (94.6%), in which the oocyte nuclei presented condensed granules of heterochromatin. Round or elongated shaped mitochondria constituted the most abundant organelles. In regard of the SSV, the protocol using the dimethylsulfoxide (DMSO) 3M possibility the preservation of 69.5% of morphologically normal PF, which was evidenced by the light and transmission electronic microscopy. At third experiment, the evaluation of the SSV procedure on the morphology and viability in situ PF form collared peccaries (Pecari tajacu) was performed. No differences were observed among treatments, in which the use of DMSO, ethylene glycol (EG) and dimethylformamide (DMF) as cryoprotectants, regardless its concentration, promoted the morphology preservation of much than 70% of PF. Concerning the PF viability, the DMSO and EG promoted the best preservation. The fourth experiment aimed to evaluate the effect of α MEM+ or TCM199 associated or not to 50 ng of FSHr on the morphology, activation and growth of collared peccaries PF, in vitro cultured (IVC) during 1 or 7 days and the effect on the extracellular matrix (ECM). After 7 days of IVC only the use of TCM199/FSH maintained the proportion of intact PF, similar to day 1(63.2%), however, no differences were observed among treatments (P>0.05). Also, an improvement of the proportion of intact growing PF was verified (P>0.05). By the Ag-NOR analysis it was observed that only the treatment using TCM199/FSH promoted the maintenance of cell proliferation similar to day 1 (P>0.05). The picrosirius red stain revealed that ECM remained intact in all treatments (P>0.05). Thus, as the general conclusion, the use of MOEPF in the refereed species allowed the knowledge of aspects related to its reproductive morphology and physiology, enabling the germplasm conservation, with the possibility of germplasm bank formation, as the elucidation of mechanisms related to the PF survive and in vitro development.

Mortalidade segundo sua causa de morte e seus determinantes: uma análise para as capitais brasileiras e municípios do nordeste do Brasil, 2000 e 2010

This dissertation considered the development of two papers, both related to mortality in Brazil. In the first article, "The context of mortality according to the three broad groups of causes of death in Brazilian capitals, 2000 and 2010", the objective was to analyze the mortality rate according to the three major groups of causes of death in Brazilian capitals. In the second article, "Typology and characteristics of mortality from external causes in the municipalities in the Northeast of Brazil, 2000 and 2010", it was built up a typology for the Northeastern municipalities taking into account information on mortality from external causes and a set of indicators related to socioeconomic, demographic, and infrastructure aspects of such municipalities, both articles for the years 2000 and 2010. Thus, we used data from the Mortality Information System of the Ministry of Health. Furthermore, it was used information from the Demographic Census for those years. The variables relating to socioeconomic and demographic conditions used in this study were those available on the home page of the United Nations Program for Development. The variables relating to socioeconomic and demographic conditions used in this study were those available on the home page of the United Nations Program for Development. Was used in Article 1 the pro-rata distribution method to accomplish the redistribution of ill-defined causes. Moreover, made use of the technique of cluster analysis with the aim of grouping the capital that had proportions of deaths from ill-defined causes similar to each other. Already in Section 2, we used the technique of Empirical Bayesian estimation; spatial statistics technique; and finally, the Grade of Membership method to find types of municipalities from information on mortality from external causes associated with socioeconomic, demographic and infrastructure variables. As the main results, it stands out in Article 1, in relation to data quality, we observed the formation of four groups of similar capital between themselves, as the proportion of illdefined causes. Regarding the behavior of mortality, according to the three major groups of causes of death, it was noted both for 2000 and for 2010 the prevalence of deaths from noncommunicable diseases for both sexes, although the reduction was identified rates in some of the capitals. Communicable diseases stood out as the second cause of death among women. Also, we found that deaths due to external causes are responsible for the second cause of death among men, as well as presenting an increase among women. As for the Article 2, stands out, in general, not just an extension of mortality from external causes in the municipalities, as well as an enlargement of the configurator stain existence of external cause deaths for the whole area of Northeast. Regarding the typology of municipalities, three vi extreme profiles were buit: the profile 1, which comprises municipalities with high rates of mortality from external causes and the best social indicators; the profile 2, that was composed of municipalities that are characterized by having low mortality rates from external causes and the lowest social indicators; and the profile 3, that brings together municipalities with intermediate mortality rates and median values considered in relation to social indicators. Although we have not seen changes in the characteristics of the profiles, we observed an increase in the proportion of municipalities that belong to the extreme profile 3, taking into account the mixed profiles.

Avaliação comparativa da eficácia dos meios de diagnóstico das vulvovaginites: implantação de tecnologia no ensino prático da ginecologia

Inaccurate diagnosis of vulvovaginitis generates inadequate treatments that cause damages women's health. Objective: evaluate the effectiveness of methods when diagnosing vulvovaginitis. Method: a cross-sectional study was performed with 200 women who complained about vaginal discharge. Vaginal smear was collected for microbiological tests, considering the gram stain method as gold standard. The efficacy of the available methods for diagnosis of vaginal discharge was assessed (sensitivity, specificity, positive predictive value and negative predictive value). Data were inserted to Graphpad Prism 6, for statistical analysis. Results: the following results were obtained: wet mount for vaginal candidiasis: sensitivity = 31%; specificity = 97%; positive predictive value (PPV) = 54%; negative predictive value (NPV) =93%; accuracy = 91%. Wet mount for bacterial vaginosis: sensitivity = 80%; specificity =95%; positive predictive value (PPV) = 80%; negative predictive value (NPV) = 95%; accuracy = 92%. Syndromic approach for bacterial vaginosis: sensitivity = 95%; specificity=43%; positive predictive value (PPV) =30%; negative predictive value (NPV) = 97%; accuracy = 54%. Syndromic approach for vaginal candidiasis: sensitivity = 75%; specificity =91%; positive predictive value (PPV) = 26%; negative predictive value (NPV) = 98%; accuracy = 90%. Pap smear for vaginal candidiasis: sensitivity = 68%, specificity = 98%; positive predictive value (PPV) = 86%; negative predictive value (NPV) =96%; accuracy = 96%. Pap smear for bacterial vaginosis: sensitivity = 75%; specificity = 100%; positive predictive value (PPV) = 100%; negative predictive value (NPV) =94%; accuracy = 95%. There was only one case of vaginal trichomoniasis reported – diagnosed by oncological cytology and wet mount – confirmed by Gram. The syndromic approach diagnosed it as bacterial vaginosis. From the data generated and with support on world literature, the Maternidade Escola Januário Cicco’s vulvovaginitis protocol was constructed. Conclusion: Pap smear and wet mount showed respectively low and very low sensitivity for vaginal candidiasis. Syndromic approach presented very low specificity and accuracy for bacterial vaginosis, which implies a large number of patients who are diagnosed or treated incorrectly.

Aplicação da perlita expandida modificada com ortofenantrolina na remoção do negro de eriocromo T em águas residuais geradas em laboratórios de ensino de química

In this study, we carried out the study of Eriochrome black T removal using expanded perlite modified orthophenanthroline by adsorption technique. The study of the adsorption process was performed by investigating the effect of the initial dye concentration, contact time and pH range of the solution (acidic and alkaline) in the adsorption process, for a so-called synthetic effluent (aqueous solution of black eriochrome T) and a real effluent (generated from the test for determining the water hardness, by complexation titration). The materials were characterized by Thermogravimetry / Differential Thermal Analysis (TG / DTA), absorption spectroscopy in the infrared (IR), X-ray Diffraction (XRD) and scanning electron microscopy (SEM). By analysis of XRD observed thinking on orthophenanthroline the modified expanded perlite. And by IR analysis showed an increase in intensity and a detailed enlargement of the absorption band related to the axial deformation of the OH bond of silanol groups of perlite (Si-OH). In the equilibration time of the study, in the evaluated time range (5-230 min) was not possible to observe the existence of a balance of time, probably attributed to the type of interaction between the Eriochrome black-T and the expanded perlite modified orthophenanthroline, being an interaction of surface origin. In the study effect of the initial concentration of the adsorbate in the case 2,0x10-4 mol / L natural pH (pH 5) gave the highest removal percentage value of eriochrome T black color with 63.74 % removal in 20 minutes of contact. In evaluating the effect of varying the pH of Eriochrome black T solution in the adsorption process, it was found that the more acidic the environment, the greater the percentage stain removal, being a result of acid-base interaction between the adsorbate and the adsorbent. In T Eriochrome black removal study in real effluent we used the optimized conditions by studying with synthetic sewage. The dye removal at pH 10, natural pH of the effluent was no significant reaching the maximum amount of color removal percentage of 8.12%, obtained already at pH 3 with maximum color removal 100.00% of color, once more proving that eriochrome black T and effectively interact better with the adsorbent at acid pH values (pH 5 or 3), and most efficiently at pH 3. thus one can mention that the perlite expanded (an amorphous aluminosilicate naturally acid) modified with orthophenanthroline (one Bronsted base) consists of a master and effective removal of coloring material in the acid-type aqueous solution, the conditions expressed in this study, can be applied as an adsorbent of this dye also mums real effluent.

Bulk sediment characteristics and geomicrobiology of sediment core 5022-1J from Laguna Potrok Aike, southern Patagonia

Living microorganisms inhabit every environment of the biosphere but only in the last decades their importance governing biochemical cycles in deep sediments has been widely recognized. Most investigations have been accomplished in the marine realm whereas there is a clear paucity of comparable studies in lacustrine sediments. One of the main challenges is to define geomicrobiological proxies that can be used to identify different microbial signals in the sediments. Laguna Potrok Aike, a maar lake located in Southeastern Patagonia, has an annually not stratifying cold water column with temperatures ranging between 4 and 10 °C, and most probably an anoxic water/sediment interface. These unusual features make it a peculiar and interesting site for geomicrobiological studies. Living microbial activity within the sediments was inspected by the first time in a sedimentary core retrieved during an ICDP-sponsored drilling operation. The main goals to study this cold subsaline environment were to characterize the living microbial consortium; to detect early diagenetic signals triggered by active microbes; and to investigate plausible links between climate and microbial populations. Results from a meter long gravity core suggest that microbial activity in lacustrine sediments can be sustained deeper than previously thought due to their adaptation to both changing temperature and oxygen availability. A multi-proxy study of the same core allowed defining past water column conditions and further microbial reworking of the organic fraction within the sediments. Methane content shows a gradual increase with depth as a result of the fermentation of methylated substrates, first methanogenic pathway to take place in the shallow subsurface of freshwater and subsaline environments. Statistical analyses of DGGE microbial diversity profiles indicate four clusters for Bacteria reflecting layered communities linked to the oxidant type whereas three clusters characterize Archaea communities that can be linked to both denitrifiers and methanogens. Independent sedimentary and biological proxies suggest that organic matter production and/or preservation have been lower during the Medieval Climate Anomaly (MCA) coinciding with a low microbial colonization of the sediments. Conversely, a reversed trend with higher organic matter content and substantial microbial activity characterizes the sediments deposited during the Little Ice Age (LIA). Thus, the initial sediments deposited during distinctive time intervals under contrasting environmental conditions have to be taken into account to understand their impact on the development of microbial communities throughout the sediments and their further imprint on early diagenetic signals.

FtsZ Protofilament Curvature is the Opposite of Tubulin Rings

Bacterial tubulin homolog FtsZ assembles straight protofilaments (pfs) that form the scaffold of the cytokinetic Z ring. These pfs can adopt a curved conformation forming a miniring or spiral tube 24 nm in diameter. Tubulin pfs also have a curved conformation, forming 42 nm tubulin rings. We have previously provided evidence that FtsZ generates a constriction force by switching from straight pfs to the curved conformation, generating a bending force on the membrane. In the simplest model the membrane tether, which exits from the C terminus of the globular FtsZ, would have to be on the outside of the curved pf. However, it is well established that tubulin rings have the C terminus on the inside of the ring. Could FtsZ and tubulin rings have the opposite curvature? In the present study we explored the direction of curvature of FtsZ rings by fusing large protein tags to the N or C terminus of the FtsZ globular domain. FtsZ with a protein tag on the N terminus did not assemble tubes. This was expected if the N terminus is on the inside, because the protein tags are too big to fit in the interior of the tube. FtsZ with C-terminal tags assembled normal tubes, consistent with the C terminus on the outside. The FN extension was not visible in negative stain, but thin section EM gave definitive evidence that the C-terminal tag was on the outside of the tubes. This has interesting implications for the evolution of tubulin. It seems likely that tubulin began with the curvature of FtsZ, which would have resulted in pfs curving toward the interior of a disassembling MT. Evolution not only eliminated this undesirable curvature, but managed to reverse direction to produce the outward curving rings, which is useful for pulling chromosomes.