Evaluation of electrocoagulation for the pre-treatment of coal seam water

This work explored the applicability of electrocoagulation (EC) using aluminium electrodes for the removal of contaminants which can scale and foul reverse osmosis membranes from a coal seam (CS) water sample, predominantly comprising sodium chloride, and sodium bicarbonate. In general, the removal efficiency of species responsible for scaling and fouling was enhanced by increasing the applied current density/voltage and contact times (30–60 s) in the EC chamber. High removal efficiencies of species potentially responsible for scale formation in reverse osmosis units such as calcium (100%), magnesium (87.9%), strontium (99.3%), barium (100%) and silicates (98.3%) were achieved. Boron was more difficult to eliminate (13.3%) and this was postulated to be due to the elevated solution pH. Similarly, fluoride removal from solution (44%) was also inhibited by the presence of hydroxide ions in the pH range 9–10. Analysis of produced flocs suggested the dominant presence of relatively amorphous boehmite (AlOOH), albeit the formation of Al(OH)3 was not ruled out as the drying process employed may have converted aluminium hydroxide to aluminium oxyhydroxide species. Evidence for adsorption of contaminants on floc surface sites was determined from FTIR studies. The quantity of aluminium released during the electrocoagulation process was higher than the Faradaic amount which suggested that the high salt concentrations in the coal seam water had chemically reacted with the aluminium electrodes.

Optimización de procesos de recubrimiento para herramientas de corte. Tecnologías de recubrimiento, métodos de caracterización y optimización de las propiedades

249 p.

Development of graphite epoxy housing for nickel-cadmium cell /

"Presented to Society for the Advancement of Material & Processing Engineering at 9th National Technical Conference, October 4-6, 1977, Atlanta, Georgia."

Enticing general engineering undergrads into signal processing with Photo-Editing and image search

The University of Cambridge is unusual in that its Department of Engineering is a single department which covers virtually all branches of engineering under one roof. In their first two years of study, our undergrads study the full breadth of engineering topics and then have to choose a specialization area for the final two years of study. Here we describe part of a course, given towards the end of their second year, which is designed to entice these students to specialize in signal processing and information engineering topics for years 3 and 4. The course is based around a photo editor and an image search application, and it requires no prior knowledge of the z-transform or of 2-dimensional signal processing. It does assume some knowledge of 1-D convolution and basic Fourier methods and some prior exposure to Matlab. The subject of this paper, the photo editor, is written in standard Matlab m-files which are fully visible to the students and help them to see how specific algorithms are implemented in detail. © 2011 IEEE.

Using hybrid knowledge engineering and image processing in color virtual restoration of ancient murals

IEEE Transactions on Knowledge and Data Engineering, vol. 15, no. 5, pp. 1338-1343, 2003.

Catalytic conversion of sodium lignosulphonate to vanillin –engineering aspects. Part 1 Effect of processing conditionson vanillin yield and selectivity

The commercial production of vanillin from sodium lignosulfonate under highly alkaline conditions, catalyzed by Cu2+ at elevated temperature and pressures up to 10 bar, has been simulated in a 3-L stirred reactor. Initially, the process was operated in the presence of nitrogen in dead-end mode, and it was shown that vanillin and vanillic acid were formed by hydrolysis at temperatures of 120, 140, and 160 °C. At the two higher temperatures, the amount of vanillin produced was the same. Subsequently, experiments were conducted at the same elevated pressures and temperatures with addition of air or oxygen-enriched air once the temperature in the reactor had reached temperatures similar to those used when only hydrolysis occurred. In this case, the concentration of vanillin at 140 and 160 °C was equal to that due to hydrolysis, and the subsequent 2-fold increase was due to oxidation. In addition, both vanillic acid and acetovanillone (which has rarely been reported) were produced, as was hydrogen. Thus, for the first time, it has been shown that the production of vanillin (and other compounds) from sodium lignosulfonate at elevated temperatures involves hydrolysis and oxidation, with hydrolysis starting at just above 100 °C, that is, much lower than has previously been reported. Approximately 50% is produced by each mechanism. In addition, the orders of the reactions of the different steps were estimated, and the reaction mechanisms are discussed.

Reverse Engineering tools: development and experimentation of innovative methods for physical and geometrical data integration and post-processing

In recent years, the use of Reverse Engineering systems has got a considerable interest for a wide number of applications. Therefore, many research activities are focused on accuracy and precision of the acquired data and post processing phase improvements. In this context, this PhD Thesis deals with the definition of two novel methods for data post processing and data fusion between physical and geometrical information. In particular a technique has been defined for error definition in 3D points’ coordinates acquired by an optical triangulation laser scanner, with the aim to identify adequate correction arrays to apply under different acquisition parameters and operative conditions. Systematic error in data acquired is thus compensated, in order to increase accuracy value. Moreover, the definition of a 3D thermogram is examined. Object geometrical information and its thermal properties, coming from a thermographic inspection, are combined in order to have a temperature value for each recognizable point. Data acquired by an optical triangulation laser scanner are also used to normalize temperature values and make thermal data independent from thermal-camera point of view.

Image processing for safety assessment in Civil Engineering

Behaviour analysis of construction safety systems is of fundamental importance to avoid accidental injuries. Traditionally, measurements of dynamic actions in Civil Engineering have been done through accelerometers, but high-speed cameras and image processing techniques can play an important role in this area. Here, we propose using morphological image filtering and Hough transform on high-speed video sequence as tools for dynamic measurements on that field. The presented method is applied to obtain the trajectory and acceleration of a cylindrical ballast falling from a building and trapped by a thread net. Results show that safety recommendations given in construction codes can be potentially dangerous for workers.