Particle emissions, volatility, and toxicity from an ethanol fumigated compression ignition engine

Particle emissions, volatility, and the concentration of reactive oxygen species (ROS) were investigated for a pre-Euro I compression ignition engine to study the potential health impacts of employing ethanol fumigation technology. Engine testing was performed in two separate experimental campaigns with most testing performed at intermediate speed with four different load settings and various ethanol substitutions. A scanning mobility particle sizer (SMPS) was used to determine particle size distributions, a volatilization tandem differential mobility analyzer (V-TDMA) was used to explore particle volatility, and a new profluorescent nitroxide probe, BPEAnit, was used to investigate the potential toxicity of particles. The greatest particulate mass reduction was achieved with ethanol fumigation at full load, which contributed to the formation of a nucleation mode. Ethanol fumigation increased the volatility of particles by coating the particles with organic material or by making extra organic material available as an external mixture. In addition, the particle-related ROS concentrations increased with ethanol fumigation and were associated with the formation of a nucleation mode. The smaller particles, the increased volatility, and the increase in potential particle toxicity with ethanol fumigation may provide a substantial barrier for the uptake of fumigation technology using ethanol as a supplementary fuel.

Gaseous and particle emissions from an ethanol fumigated compression ignition engine

A 4-cylinder Ford 2701C test engine was used in this study to explore the impact of ethanol fumigation on gaseous and particle emission concentrations. The fumigation technique delivered vaporised ethanol into the intake manifold of the engine, using an injector, a pump and pressure regulator, a heat exchanger for vaporising ethanol and a separate fuel tank and lines. Gaseous (Nitric oxide (NO), Carbon monoxide (CO) and hydrocarbons (HC)) and particulate emissions (particle mass (PM2.5) and particle number) testing was conducted at intermediate speed (1700 rpm) using 4 load settings with ethanol substitution percentages ranging from 10-40 % (by energy). With ethanol fumigation, NO and PM2.5 emissions were reduced, whereas CO and HC emissions increased considerably and particle number emissions increased at most test settings. It was found that ethanol fumigation reduced the excess air factor for the engine and this led to increased emissions of CO and HC, but decreased emissions of NO. PM2.5 emissions were reduced with ethanol fumigation, as ethanol has a very low “sooting” tendency. This is due to the higher hydrogen-to-carbon ratio of this fuel, and also because ethanol does not contain aromatics, both of which are known soot precursors. The use of a diesel oxidation catalyst (as an after-treatment device) is recommended to achieve a reduction in the four pollutants that are currently regulated for compression ignition engines. The increase in particle number emissions with ethanol fumigation was due to the formation of volatile (organic) particles; consequently, using a diesel oxidation catalyst will also assist in reducing particle number emissions.

Concentration and oxidative potential of on-road particle emissions and their relationship with traffic composition : Relevance to exposure assessment

Particles emitted by vehicles are known to cause detrimental health effects, with their size and oxidative potential among the main factors responsible. Therefore, understanding the relationship between traffic composition and both the physical characteristics and oxidative potential of particles is critical. To contribute to the limited knowledge base in this area, we investigated this relationship in a 4.5 km road tunnel in Brisbane, Australia. On-road concentrations of ultrafine particles (<100 nm, UFPs), fine particles (PM2.5), CO, CO2 and particle associated reactive oxygen species (ROS) were measured using vehicle-based mobile sampling. UFPs were measured using a condensation particle counter and PM2.5 with a DustTrak aerosol photometer. A new profluorescent nitroxide probe, BPEAnit, was used to determine ROS levels. Comparative measurements were also performed on an above-ground road to assess the role of emission dilution on the parameters measured. The profile of UFP and PM2.5 concentration with distance through the tunnel was determined, and demonstrated relationships with both road gradient and tunnel ventilation. ROS levels in the tunnel were found to be high compared to an open road with similar traffic characteristics, which was attributed to the substantial difference in estimated emission dilution ratios on the two roadways. Principal component analysis (PCA) revealed that the levels of pollutants and ROS were generally better correlated with total traffic count, rather than the traffic composition (i.e. diesel and gasoline-powered vehicles). A possible reason for the lack of correlation with HDV, which has previously been shown to be strongly associated with UFPs especially, was the low absolute numbers encountered during the sampling. This may have made their contribution to in-tunnel pollution largely indistinguishable from the total vehicle volume. For ROS, the stronger association observed with HDV and gasoline vehicles when combined (total traffic count) compared to when considered individually may signal a role for the interaction of their emissions as a determinant of on-road ROS in this pilot study. If further validated, this should not be overlooked in studies of on- or near-road particle exposure and its potential health effects.

Measurements of particle emissions from nanotechnology processes, with assessment of measuring techniques and workplace controls

The overall aim of this project was to contribute to existing knowledge regarding methods for measuring characteristics of airborne nanoparticles and controlling occupational exposure to airborne nanoparticles, and to gather data on nanoparticle emission and transport in various workplaces. The scope of this study involved investigating the characteristics and behaviour of particles arising from the operation of six nanotechnology processes, subdivided into nine processes for measurement purposes. It did not include the toxicological evaluation of the aerosol and therefore, no direct conclusion was made regarding the health effects of exposure to these particles. Our research included real-time measurement of sub, and supermicrometre particle number and mass concentration, count median diameter, and alveolar deposited surface area using condensation particle counters, an optical particle counter, DustTrak photometer, scanning mobility particle sizer, and nanoparticle surface area monitor, respectively. Off-line particle analysis included scanning and transmission electron microscopy, energy-dispersive x-ray spectrometry, and thermal optical analysis of elemental carbon. Sources of fibrous and non-fibrous particles were included.

Composition and morphology of particle emissions from in-use aircraft during takeoff and landing

In order to provide realistic data for air pollution inventories and source apportionment at airports, the morphology and composition of ultrafine particles (UFP) in aircraft engine exhaust were measured and characterized. For this purpose, two independent measurement techniques were employed to collect emissions during normal takeoff and landing operations at Brisbane Airport, Australia. PM1 emissions in the airfield were collected on filters and analyzed using the particle-induced X-ray emission (PIXE) technique. Morphological and compositional analyses of individual ultrafine particles in aircraft plumes were performed on silicon nitride membrane grids using transmission electron microscopy (TEM) combined with energy-dispersive X-ray microanalysis (EDX). TEM results showed that the deposited particles were in the range of 5 to 100 nm in diameter, had semisolid spherical shapes and were dominant in the nucleation mode (18 – 20 nm). The EDX analysis showed the main elements in the nucleation particles were C, O, S and Cl. The PIXE analysis of the airfield samples was generally in agreement with the EDX in detecting S, Cl, K, Fe and Si in the particles. The results of this study provide important scientific information on the toxicity of aircraft exhaust and their impact on local air quality.

Biodiesel with controlled physicochemical properties, a means to further reduce diesel engine particle emissions

The issue of particle emissions from diesel engines is still a matter of concern due its deleterious effects both on human health and environment(Ristovski et al., 2012). Recently, International Agency for Research on Cancer (IARC) inclusion of diesel engine exhaust particles as carcinogenic to human health added a new margin on it. Apart from the use of after treatment technology, biodiesel is also considered as potential way to reduce particle emission alongside with other emissions(Xue, Grift, & Hansen, 2011). Global biodiesel production is still reasonably small compared to its counterpart fossil diesel, but even this small amount comes from a wide variety of feed stocks. Contrary to fossil diesel, the important physicochemical properties of biodiesel vary among different feed stocks(Hoekman, Broch, Robbins, Ceniceros, & Natarajan, 2012).

Performance and gaseous and particle emissions from a liquefied petroleum gas (LPG) fumigated compression ignition engine

In this study, an LPG fumigation system was fitted to a Euro III compression ignition (CI) engine to explore its impact on performance, and gaseous and particulate emissions. LPG was introduced to the intake air stream (as a secondary fuel) by using a low pressure fuel injector situated upstream of the turbocharger. LPG substitutions were test mode dependent, but varied in the range of 14-29% by energy. The engine was tested over a 5 point test cycle using ultra low sulphur diesel (ULSD), and a low and high LPG substitution at each test mode. The results show that LPG fumigation coerces the combustion into pre-mixed mode, as increases in the peak combustion pressure (and the rate of pressure rise) were observed in most tests. The emissions results show decreases in nitric oxide (NO) and particulate matter (PM2.5) emissions; however, very significant increases in carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. A more detailed investigation of the particulate emissions showed that the number of particles emitted was reduced with LPG fumigation at all test settings – apart from mode 6 of the ECE R49 test cycle. Furthermore, the particles emitted generally had a slightly larger median diameter with LPG fumigation, and had a smaller semi-volatile fraction relative to ULSD. Overall, the results show that with some modifications, LPG fumigation systems could be used to extend ULSD supplies without adversely impacting on engine performance and emissions.

Influences of biodiesel chemical compositions and physical properties on engine exhaust particle emissions

This thesis presents a comprehensive study on the influences of biodiesel chemical composition and physical properties on diesel engine exhaust particle emissions. It examines biodiesels from several feedstocks having wide variations in their chemical composition (carbon chain length, unsaturation and oxygen content) and physical properties (density, viscosity, surface tension, boiling point etc.), and evaluates their influence on exhaust particle emissions. The outcome of this thesis is significant since it reveals the importance of regulating biodiesels chemical composition in order to ensure lowest possible emissions with better overall performance.

Particle emissions from biodiesels with different physical properties and chemical composition

Biodiesels produced from different feedstocks usually have wide variations in their fatty acid methyl ester (FAME) so that their physical properties and chemical composition are also different. The aim of this study is to investigate the effect of the physical properties and chemical composition of biodiesels on engine exhaust particle emissions. Alongside with neat diesel, four biodiesels with variations in carbon chain length and degree of unsaturation have been used at three blending ratios (B100, B50, B20) in a common rail engine. It is found that particle emission increased with the increase of carbon chain length. However, for similar carbon chain length, particle emissions from biodiesel having relatively high average unsaturation are found to be slightly less than that of low average unsaturation. Particle size is also found to be dependent on fuel type. The fuel or fuel mix responsible for higher particle mass (PM) and particle number (PN) emissions is also found responsible for larger particle median size. Particle emissions reduced consistently with fuel oxygen content regardless of the proportion of biodiesel in the blends, whereas it increased with fuel viscosity and surface tension only for higher diesel–biodiesel blend percentages (B100, B50). However, since fuel oxygen content increases with the decreasing carbon chain length, it is not clear which of these factors drives the lower particle emission. Overall, it is evident from the results presented here that chemical composition of biodiesel is more important than its physical properties in controlling exhaust particle emissions.

Characterisation of gas and particle emissions from wildfires

Os incêndios florestais são uma importante fonte de emissão de compostos gasosos e de aerossóis. Em Portugal, onde a maioria dos incêndios ocorre no norte e centro do país, os incêndios destroem todos os anos milhares de hectares, com importantes perdas em termos económicos, de vidas humanas e qualidade ambiental. As emissões podem alterar consideravelmente a química da atmosfera, degradar a qualidade do ar e alterar o clima. Contudo, a informação sobre as caraterísticas das emissões dos incêndios florestais nos países do Mediterrâneo é limitada. Tanto a nível nacional como internacional, existe um interesse crescente na elaboração de inventários de emissões e de regulamentos sobre as emissões de carbono para a atmosfera. Do ponto de vista atmosférico da monitorização atmosférica, os incêndios são considerados um desafio, dada a sua variabilidade temporal e espacial, sendo de esperar um aumento da sua frequência, dimensão e severidade, e também porque as estimativas de emissões dependem das caraterísticas dos biocombustíveis e da fase de combustão. O objetivo deste estudo foi quantificar e caraterizar as emissões de gases e aerossóis de alguns dos mais representativos incêndios florestais que ocorreram no centro de Portugal nos verões de 2009 e de 2010. Efetuou-se a colheita de amostras de gases e de duas frações de partículas (PM2.5 e PM2.5-10) nas plumas de fumo em sacos Tedlar e em filtros de quartzo acoplados a um amostrador de elevado volume, respetivamente. Os hidrocarbonetos totais (THC) e óxidos de carbono (CO e CO2) nas amostras gasosas foram analisados em instrumentos automáticos de ionização de chama e detetores não dispersivos de infravermelhos, respetivamente. Para algumas amostras, foram também quantificados alguns compostos de carbonilo após reamostragem do gás dos sacos Tedlar em cartuchos de sílica gel revestidos com 2,4-dinitrofenilhidrazina (DNPH), seguida de análise por cromatografia líquida de alta resolução. Nas partículas, analisou-se o carbono orgânico e elementar (técnica termo-óptica), iões solúveis em água (cromatografia iónica) e elementos (espectrometria de massa com plasma acoplado por indução ou análise instrumental por ativação com neutrões). A especiação orgânica foi obtida por cromatografia gasosa acoplada a espectrometria de massa após extração com recurso a vários solventes e separação dos extratos orgânicos em diversas classes de diferentes polaridades através do fracionamento com sílica gel. Os fatores de emissão do CO e do CO2 situaram-se nas gamas 52-482 e 822-1690 g kg-1 (base seca), mostrando, respetivamente, correlação negativa e positiva com a eficiência de combustão. Os fatores de emissão dos THC apresentaram valores mais elevados durante a fase de combustão latente sem chama, oscilando entre 0.33 e 334 g kg-1 (base seca). O composto orgânico volátil oxigenado mais abundante foi o acetaldeído com fatores de emissão que variaram desde 1.0 até 3.2 g kg-1 (base seca), seguido pelo formaldeído e o propionaldeído. Observou-se que as emissões destes compostos são promovidas durante a fase de combustão latente sem chama. Os fatores de emissão de PM2.5 e PM10 registaram valores entre 0.50-68 e 0.86-72 g kg-1 (base seca), respetivamente. A emissão de partículas finas e grosseiras é também promovida em condições de combustão lenta. As PM2.5 representaram cerca de 90% da massa de partículas PM10. A fração carbonosa das partículas amostradas em qualquer dos incêndios foi claramente dominada pelo carbono orgânico. Foi obtida uma ampla gama de rácios entre o carbono orgânico e o carbono elementar, dependendo das condições de combustão. Contudo, todos os rácios refletiram uma maior proporção de carbono orgânico em relação ao carbono elementar, típica das emissões de queima de biomassa. Os iões solúveis em água obtidos nas partículas da pluma de fumo contribuíram com valores até 3.9% da massa de partículas PM2.5 e 2.8% da massa de partículas de PM2.5-10. O potássio contribuiu com valores até 15 g mg-1 PM2.5 e 22 g mg-1 PM2.5-10, embora em massa absoluta estivesse maioritariamente presente nas partículas finas. Os rácios entre potássio e carbono elementar e entre potássio e carbono orgânico obtidos nas partículas da pluma de fumo enquadram-se na gama de valores relatados na literatura para emissões de queima de biomassa. Os elementos detetados nas amostras representaram, em média, valores até 1.2% e 12% da massa de PM2.5 e PM2.5-10, respetivamente. Partículas resultantes de uma combustão mais completa (valores elevados de CO2 e baixos de CO) foram caraterizadas por um elevado teor de constituintes inorgânicos e um menor conteúdo de matéria orgânica. Observou-se que a matéria orgânica particulada é composta principalmente por componentes fenólicos e produtos derivados, séries de compostos homólogos (alcanos, alcenos, ácidos alcanóicos e alcanóis), açúcares, biomarcadores esteróides e terpenóides, e hidrocarbonetos aromáticos policíclicos. O reteno, um biomarcador das emissões da queima de coníferas, foi o hidrocarboneto aromático dominante nas amostras das plumas de fumo amostradas durante a campanha que decorreu em 2009, devido ao predomínio de amostras colhidas em incêndios em florestas de pinheiros. O principal açúcar anidro, e sempre um dos compostos mais abundantes, foi o levoglucosano. O rácio levoglucosano/OC obtido nas partículas das plumas de fumo, em média, registaram valores desde 5.8 a 23 mg g-1 OC. Os rácios levoglucosano/manosano e levoglucosano/(manosano+galactosano) revelaram o predomínio de amostras provenientes da queima de coníferas. Tendo em conta que a estimativa das emissões dos incêndios florestais requer um conhecimento de fatores de emissão apropriados para cada biocombustível, a base de dados abrangente obtida neste estudo é potencialmente útil para atualizar os inventários de emissões. Tem vindo a ser observado que a fase de combustão latente sem chama, a qual pode ocorrer simultaneamente com a fase de chama e durar várias horas ou dias, pode contribuir para uma quantidade considerável de poluentes atmosféricos, pelo que os fatores de emissão correspondentes devem ser considerados no cálculo das emissões globais de incêndios florestais. Devido à falta de informação detalhada sobre perfis químicos de emissão, a base de dados obtida neste estudo pode também ser útil para a aplicação de modelos no recetor no sul da Europa.

Photon-induced multiple particle emissions of Zr90 and natZr from 10 to 140 MeV

A comprehensive analysis of electrodisintegration yields of protons on Zr90 is proposed taking into account the giant dipole resonance, isovector giant quadrupole resonance (IVGQR), and quasideuteron contributions to the total photoabsorption cross section from 10 to 140 MeV. The calculation applies the MCMC intranuclear cascade to address the direct and pre-equilibrium emissions and another Monte Carlo-based algorithm to describe the evaporation step. The final results of the total photoabsorption cross section for Zr90 and relevant decay channels are obtained by fitting the (e,p) measurements from the National Bureau of Standards and show that multiple proton emissions dominate the photonuclear reactions at higher energies. These results provide a consistent explanation for the exotic and steady increase of the (e,p) yield and also a strong evidence of a IVGQR with a strength parameter compatible with the E2 energy-weighted sum rule. The inclusive photoneutron cross sections for Zr90 and natZr, derived from these results and normalized with the (e,p) data, are in agreement within 10% with both Livermore and Saclay data up to 140 MeV. © 2007 The American Physical Society.

Performance and gaseous and particle emissions from a liquefied petroleum gas (LPG) fumigated compression ignition engine

In this study, an LPG fumigation system was fitted to a Euro III compression ignition (CI) engine to explore its impact on performance, and gaseous and particulate emissions. LPG was introduced to the intake air stream (as a secondary fuel) by using a low pressure fuel injector situated upstream of the turbocharger. LPG substitutions were test mode dependent, but varied in the range of 14-29% by energy. The engine was tested over a 5 point test cycle using ultra low sulphur diesel (ULSD), and a low and high LPG substitution at each test mode. The results show that LPG fumigation coerces the combustion into pre-mixed mode, as increases in the peak combustion pressure (and the rate of pressure rise) were observed in most tests. The emissions results show decreases in nitric oxide (NO) and particulate matter (PM2.5) emissions; however, very significant increases in carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. A more detailed investigation of the particulate emissions showed that the number of particles emitted was reduced with LPG fumigation at all test settings – apart from mode 6 of the ECE R49 test cycle. Furthermore, the particles emitted generally had a slightly larger median diameter with LPG fumigation, and had a smaller semi-volatile fraction relative to ULSD. Overall, the results show that with some modifications, LPG fumigation systems could be used to extend ULSD supplies without adversely impacting on engine performance and emissions.