An evidence-based brochure to educate contact lens wearers about safe contact lens wear

Contact lenses are a successful and popular means to correct refractive error and are worn by just under 700,000 Australians1 and approximately 125 million people worldwide. The most serious complication of contact lens wear is microbial keratitis, a potentially sight-threatening corneal infection most often caused by bacteria. Gram-negative bacteria, in particular pseudomonas species, account for the majority of severe bacterial infections. Pathogens such as fungi or amoebae, which feature less often, are associated with significant morbidity. These unusual pathogens have come into the spotlight in recent times with an apparent association with specific lens cleaning solutions...

Application of Three-Dimensional Discrete Element Face-to-Face Contact Model with Fissure Water Pressure to Stability Analysis of Landslide in Panluo Iron Mine

Three-dimensional discrete element face-to-face contact model with fissure water pressure is established in this paper and the model is used to simulate three-stage process of landslide under fissure water pressure in the opencast mine, according to the actual state of landslide in Panluo iron mine where landslide happened in 1990 and was fathered in 1999. The calculation results show that fissure water pressure on the sliding surface is the main reason causing landslide and the local soft interlayer weakens the stability of slope. If the discrete element method adopts the same assumption as the limit equilibrium method, the results of two methods are in good agreement; while if the assumption is not adopted in the discrete element method, the critical phi numerically calculated is less than the one calculated by use of the limit equilibrium method for the same C. Thus, from an engineering point of view, the result from the discrete element model simulation is safer and has more widely application since the discrete element model takes into account the effect of rock mass structures.

Effect of solder volume on joint shape with variable chip-to-board contact pad ratio

The objective of this paper is to investigate the effect of the pad size ratio between the chip and board end of a solder joint on the shape of that solder joint in combination with the solder volume available. The shape of the solder joint is correlated to its reliability and thus of importance. For low density chip bond pad applications Flip Chip (FC) manufacturing costs can be kept down by using larger size board pads suitable for solder application. By using “Surface Evolver” software package the solder joint shapes associated with different size/shape solder preforms and chip/board pad ratios are predicted. In this case a so called Flip-Chip Over Hole (FCOH) assembly format has been used. Assembly trials involved the deposition of lead-free 99.3Sn0.7Cu solder on the board side, followed by reflow, an underfill process and back die encapsulation. During the assembly work pad off-sets occurred that have been taken into account for the Surface Evolver solder joint shape prediction and accurately matched the real assembly. Overall, good correlation was found between the simulated solder joint shape and the actual fabricated solder joint shapes. Solder preforms were found to exhibit better control over the solder volume. Reflow simulation of commercially available solder preform volumes suggests that for a fixed stand-off height and chip-board pad ratio, the solder volume value and the surface tension determines the shape of the joint.

Cell-to-cell contact-independent regulatory T cells in human tuberculosis

info:eu-repo/semantics/nonPublished

Skin-to-Skin contact

Skin to skin contact facilitates the initiation of breast feeding, neonatal thermoregulation and the promotion of maternal-infant attachment. However, there are cultural influences in society and in the labour ward that may make implemention of skin to skin contact difficult.

Measurement of Polymer-to-Polymer Contact Friction in Thermoforming

Contact friction plays a critical role in all the major thermoforming processes for polymers. However, these effects are very difficult to measure in practice and, as a result, have received little scientific investigation. In this work, two independently developed test methods for the measurement of elevated temperature polymer-to-polymer contact friction are presented, and their results are compared in detail for the first time. One is based on a modified moving sled friction test, whereas the other uses a rotational rheometer. In each case, friction tests were conducted between two plug and two sheet materials. The results show that broadly similar coefficients of friction were obtained from the two test methods. The measured values were quite low (<0.3) at lower temperatures and typically were higher for polypropylene (PP) sheet than for polystyrene (PS). On approaching the glass transition temperature for PS (95°C) and the crystalline melting point for PP (165°C), the friction coefficients rose very sharply, and both test techniques became increasingly unreliable. It was concluded that despite their physical differences, both test techniques were able to capture the highly temperature sensitive nature of friction between polymer materials used in thermoforming.

Registered Nurses' Perceptions about Facilitators and Barriers to Maternal Skin to Skin Contact in the Operating Room

Abstract It is recommended that all new mothers experience skin-to-skin contact (SSC) with their newborns immediately after birth. However, SSC is not commonly practiced after cesarean deliveries. To understand facilitators and barriers regarding SSC in the operating room (OR), a descriptive online and paper survey was conducted with 68 Registered Nurses from four hospitals in Ontario. The theory of planned behavior framed the study. Nurses had positive attitudes, and believed most health care team members supported SSC in the OR, but were uncertain about their control over the behavior. Nurses who had practiced the behavior in the past had more positive attitudinal and normative beliefs, and perceived some barriers as less difficult. Attitude and past behavior were the only significant multivariate predictors of intention to practice SSC in the future. Results suggest that shifting attitude and supporting more experience with the practice may increase nurses’ implementation of SSC in the OR.

Using a pressure mapping system to evaluate contact pressure on hands during use of axillary crutches

The aim of this study was to evaluate different handles used in axillary crutches with a Pressure Mapping System. The Grip Versatek system from Tekscan Inc. was used to measure the levels and the distribution of contact pressure in the hands during a simulated activity of ambulation with crutches. The sample included ten able-bodied subjects: five men and five women. The results show that the different models of handles appear to have influenced the pressure levels measured during the activity. Therefore, the measurement equipment provides parameters that allow the comparison among different designs and assess their contribution to the comprehension of the demands of ergonomic handles.

Are We Family? Lesbian Mothers and the Decision to Make Contact with Their Children's Donor Siblings

The current study examines the experiences of three lesbian families who have made contact with their children's donor siblings: a single mother by choice, a couple and a mother who had children in the context of a relationship that has since ended. It builds on prior research that has addressed this topic, but has primarily utilized survey methodology. Participants of the current study shared their experiences via focus group and individual interviews. A narrative research approach was used to analyze and present the findings.