Tracking and identifying wastewater toxicants and assessing their biodegradation products

Screening of wastewater effluents from municipal and industrial wastewater treatment plants with biotests showed that the treated wastewater effluents possess only minor acute toxic properties towards whole organisms (e.g. bacteria, algae, daphnia), if any. In vitro tests (sub-mitochondrial membranes and fish hepatocytes) were generally more susceptible to the effluents. Most of the effluents indicated the presence of hormonally active compounds, as the production of vitellogenin, an egg yolk precursor protein, was induced in fish hepatocytes exposed to wastewater. In addition, indications of slight genotoxic potential was found in one effluent concentrate with a recombinant bacteria test. Reverse electron transport (RET) of mitochondrial membranes was used as a model test to conduct effluent assessment followed by toxicant characterisations and identifications. Using a modified U.S. EPA Toxicity Identification Evaluation Phase I scheme and additional case-specific methods, the main compound in a pulp and paper mill effluent causing RET inhibition was characterised to be an organic, relatively hydrophilic high molecular weight (HMW) compound. The toxicant could be verified as HMW lignin by structural analyses using nuclear magnetic resonance. In the confirmation step commercial and in-house extracted lignin products were used. The possible toxicity related structures were characterised by statistical analysis of the chemical breakdown structures of laboratory-scale pulping and bleaching effluents and the toxicities of these effluents. Finally, the biological degradation of the identified toxicant and other wastewater constituents was evaluated using bioassays in combination with chemical analyses. Biological methods have not been used routinely in establishing effluent discharge limits in Finland. However, the biological effects observed in this study could not have been predicted using only routine physical and chemical effluent monitoring parameters. Therefore chemical parameters cannot be considered to be sufficient in controlling effluent discharges especially in case of unknown, possibly bioaccumulative, compounds that may be present in small concentrations and may cause chronic effects.

Association genetics in Corymbia citriodora subsp variegata identifies single nucleotide polymorphisms affecting wood growth and cellulosic pulp yield

Wood is an important biological resource which contributes to nutrient and hydrology cycles through ecosystems, and provides structural support at the plant level. Thousands of genes are involved in wood development, yet their effects on phenotype are not well understood. We have exploited the low genomic linkage disequilibrium (LD) and abundant phenotypic variation of forest trees to explore allelic diversity underlying wood traits in an association study. Candidate gene allelic diversity was modelled against quantitative variation to identify SNPs influencing wood properties, growth and disease resistance across three populations of Corymbia citriodora subsp. variegata, a forest tree of eastern Australia. Nine single nucleotide polymorphism (SNP) associations from six genes were identified in a discovery population (833 individuals). Associations were subsequently tested in two smaller populations (130160 individuals), validating our findings in three cases for actin 7 (ACT7) and COP1 interacting protein 7 (CIP7). The results imply a functional role for these genes in mediating wood chemical composition and growth, respectively. A flip in the effect of ACT7 on pulp yield between populations suggests gene by environment interactions are at play. Existing evidence of gene function lends strength to the observed associations, and in the case of CIP7 supports a role in cortical photosynthesis.

Studies on metal complex formation of environmentally friendly aminopolycarboxylate chelating agents

Aminopolykarboksyylaatteja, kuten etyleenidiamiinitetraetikkahappoa (EDTA), on käytetty useiden vuosikymmenien ajan erinomaisen metalli-ionien sitomiskyvyn vuoksi kelatointiaineena lukuisissa sovelluksissa sekä analytiikassa että monilla teollisisuuden aloilla. Näiden yhdisteiden biohajoamattomuus on kuitenkin herättänyt huolta viime aikoina, sillä niiden on havaittu olevan hyvin pysyviä luonnossa. Tämä työ on osa laajempaa tutkimushanketta, jossa on tavoitteena löytää korvaavia kelatointiaineita EDTA:lle. Tutkimuksen aiheena on kuuden kelatointiaineen metalli-ionien sitomiskyvyn kartoitus. EDTA:a paremmin luonnossa hajoavina nämä ovat ympäristöystävällisiä ehdokkaita korvaaviksi kelatointiaineiksi useisiin sovelluksiin. Työssä tutkittiin niiden kompleksinmuodostusta useiden metalli-ionien kanssa potentiometrisella titrauksella. Metalli-ionivalikoima vaihteli hieman kelatointiaineesta riippuen sisältäen magnesium-, kalsium-, mangaani-, rauta-, kupari-, sinkki-, kadmium-, elohopea-, lyijy- ja lantaani-ionit. Tutkittavat metallit oli valittu tähtäimessä olevien sovellusten, synteesissä ilmenneiden ongelmien tai ympäristönäkökohtien perusteella. Tulokset osoittavat näiden yhdisteiden metallinsitomiskyvyn olevan jonkin verran heikompi kuin EDTA:lla, mutta kuitenkin riittävän useisiin sovelluksiin kuten sellunvalkaisuprosessiin. Myrkyllisten raskasmetallien, kadmiumin, elohopen ja lyijyn kohdalla EDTA:a heikompi sitoutuminen on eduksikin, koska se yhdistettynä parempaan biohajoavuuteen saattaa alentaa tutkittujen yhdisteiden kykyä mobilisoida kyseisiä metalleja sedimenteistä. Useimmilla tutkituista yhdisteistä on ympäristönäkökulmasta etuna myös EDTA:a pienempi typpipitoisuus.

Harvesting undelimbed Scots pine (Pinus sylvestris L.) from first thinnings for integrated production of kraft pulp and energy

The present study evaluates the feasibility of undelimbed Scots pine (Pinus sylvestris L.) for integrated production of pulp and energy in a kraft pulp mill from the technical, economic and environmental points of view, focusing on the potential of bundle harvesting. The feasibility of tree sections for pulp production was tested by conducting an industrial wood-handling experiment, laboratory cooking and bleaching trials, using conventional small-diameter Scots pine pulpwood as a reference. These trials showed that undelimbed Scots pine sections can be processed in favourable conditions as a blend with conventional small-diameter pulpwood without reducing the pulp quality. However, fibre losses at various phases of the process may increase when using undelimbed material. In the economic evaluation, both pulp production and wood procurement costs were considered, using the relative wood paying capability of a kraft pulp mill as a determinant. The calculations were made for three Scots pine first-thinning stands with the breast-height diameter of the removal (6 12 cm) as the main distinctive factor. The supply chains included in the comparison were based on cut-to-length harvesting, whole-tree harvesting and bundle harvesting (whole-tree bundling). With the current ratio of pulp and energy prices, the wood paying capability declines with an increase in the proportion of the energy fraction of the raw material. The supply system based on the cut-to-length method was the most efficient option, resulting in the highest residual value at stump in most cases. A decline in the pulp price and an increase in the energy price improved the competitiveness of the whole-tree systems. With short truck transportation distances and low pulp prices, however, the harvesting of loose whole trees can result in higher residual value at stump in small-diameter stands. While savings in transportation costs did not compensate for the high cutting and compaction costs by the second prototype of the bundle harvester, an increase in transportation distances improved its competitiveness. Since harvesting undelimbed assortments increases nutrient export from the site, which can affect soil productivity, the whole-tree alternatives included in the present study cannot be recommended on infertile peatlands and mineral soils. The harvesting of loose whole trees or bundled whole trees implies a reduction in protective logging residues and an increase in site traffic or payloads. These factors increase the risk of soil damage, especially on peat soils with poor bearing capacity. Within the wood procurement parameters which were examined, the CO2 emissions of the supply systems varied from 13 27 kg m3. Compaction of whole trees into bundles reduced emissions from transportation by 30 39%, but these reductions were insufficient to compensate for the increased emissions from cutting and compaction.

Optical properties change in amorphous (As2S3)(0.87)Sb-0.13 thin films by photo and thermal induced process

Exposure with above band gap light and thermal annealing at a temperature near to glass transition temperature, of thermally evaporated amorphous (As2S3)(0.87)Sb-0.13 thin films of 1 mu m thickness, were found to be accompanied by structural effects, which in turn, lead to changes in the optical properties. The optical properties of thin films induced by illumination and annealing were studied by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and Raman spectroscopy. Photo darkening or photo bleaching was observed in the film depending upon the conditions of the light exposure or annealing. These changes of the optical properties are assigned to the change of homopolar bond densities. (C) 2010 Elsevier B.V. All rights reserved.

Optical properties change with the addition and diffusion of Bi to As2S3 in the Bi/As2S3 bilayer thin film

The role of Bi layer (thickness similar to 7 nm) on As2S3 film was extensively studied for different optical applications in which Bi (top layer) as active and diffusing layer and As2S3 as barrier (matrix) layer. Bilayer thin films of Bi/As2S3 were prepared from Bi and As2S3 by thermal evaporation technique under high vacuum. The decrease of optical band gap with the addition of Bi to As2S3 has been explained on the basis of density of states and the increase in disorder in the system. It was found that the efficient changes of optical parameters (transmission, optical band gap, refraction) could be realized due to the photo induced diffusion activated by the focused 532 nm laser irradiation and formation of different bonds. The diffusion of Bi into As2S3 matrix increases the optical band gap producing photo bleaching effect. The changes were characterised by different experimental techniques. (C) 2012 Elsevier B.V. All rights reserved.

Effect of laser irradiation on optical properties of Ge12Sb25Se63 amorphous chalcogenide thin films

The change in photo-induced optical properties in thermally evaporated Ge12Sb25Se63 chalcogenide thin film under 532-nm laser illumination has been reported in this paper. The structure and composition of the film have been examined by X-ray diffraction and energy dispersive X-ray analysis, respectively. The optical properties such as refractive index, extinction coefficient and thickness of the films have been determined from the transmission spectra based on inverse synthesis method and the optical band gap has been derived from optical absorption spectra using the Tauc plot. It has been found that the mechanism of the optical absorption is due to allowed indirect transition. The optical band gap increases by 0.05 eV causing photo-bleaching mechanism, while refractive index decreases because of reduction in structural disordering. Deconvolution of Raman and X-ray photoelectron spectra into several peaks provides different structural units, which supports the optical photo-bleaching.

Studies on isolation, purification and properties of Endoglucanase from the hepatopancreas of Perna viridis

In the attempt to find out catalytic potency and properties of the endoglucanase of green mussel, it could be highlighted that the enzyme is efficient in degrading carboxymethylcellulose to reducing sugars. The immobilized enzyme will find applications in the food industry, paper and pulp industry, wood preservation, alcohol and pharmaceutical industry.The purification method employed i.e. Sephadex G100 chromatography employing affinity and exclusion principles simplify the purification procedure.Addition of Mg2+ and Co2+ at 10mM concentrations enhances endoglucanase activity of green mussel.The immobilized endoglucanase can be used for deinking mixed office waste paper. The endoglucanase if supplemented with exoglucanase and B-glucosidase under appropriate conditions would help in the recycling of paper.

Studies on pulp propogation in single mode optical fibres

Studies on pulse propagation in single mode optical fibers have attracted interest from a wide area of science and technology as they have laid down the foundation for an in-depth understanding of the underlying physical principles, especially in the field of optical telecommunications. The foremost among them is discovery of the optical soliton which is considered to be one of the most significant events of the twentieth century owing to its fantastic ability to propagate undistorted over long distances and to remain unaflected after collision with each other. To exploit the important propertia of optical solitons, innovative mathematical models which take into account proper physical properties of the single mode optical fibers demand special attention. This thesis contains a theoretical analysis of the studies on soliton pulse propagation in single mode optical fibers.

Extracts from pitanga (Eugenia uniflora L.) leaves: Influence of extraction process on antioxidant properties and yield of phenolic compounds

Different extraction processes were employed to extract the polyphenolic compounds from pitanga (Eugenia uniflora L) leaves: a one-step process using water, ethanol or supercritical CO(2) as solvents, and a two-step process using supercritical CO(2) followed by either water or ethanol. The total polyphenolic compounds, total flavonoids and antioxidant activity were determined in all the extracts obtained. The process performance was evaluated with respect to three variables: global extraction yield, concentration and yield of both polyphenols and flavonoids in the extracts. For the one-step extraction, the results showed that the extraction yield increased with solvent polarity. For the two-step process, the results suggested that water was more efficient in extracting the phenolic compounds from E. uniflora when the matrix was previously extracted with scCO(2). With respect to the antioxidant activity, the ethanolic extracts obtained from both processes, using either the DPPH radical scavenging method or the beta-carotene bleaching method, presented high antioxidant activities. (C) 2010 Elsevier B.V. All rights reserved.

The effect of homogenisation on the stability of pineapple pulp

P>Pineapple pulp was homogenised at different pressures, and its stability investigated by way of flow curves, particle size distribution, morphology, cloudiness and sedimentation. The particle size of the homogenised pulp ranged from 400 to 100 mu m for homogenisation pressures of between 0 and 700 bar. The pineapple pulp showed shear thinning behaviour with increasing flow index (n) after processing at higher pressures. In addition, the pulps with smaller particles showed less serum cloudiness, even though the sedimentation tests showed the highest stability for pulp homogenised between 200 and 300 bar. Above 400 bar, the pulp showed phase separation and higher sedimentation indexes, similar to that observed for the untreated samples, which was attributed to the formation of aggregates because of interparticle attraction.

Hydrogen peroxide and supercritical carbon dioxide: a new bleaching stage for Eucalyptus kraft-O(2) pulps

Kraft pulp is currently bleached largely by the elemental chlorine free (ECF) technology with oxygen, chlorine dioxide, and hydrogen as active agents. This technology brought about significant environmental improvements in relation to standard processes based on chlorine gas and hypochlorite, but there is still need for further improvements. This study presents a novel environmentally friendly bleaching stage - the so-called `hydrogen peroxide in supercritical carbon dioxide`, P((SC-CO2)) - that can be adapted to current ECF bleaching processes, with preference in cases where hydrogen peroxide is already used. In this study, the P((SC-CO2)) stage was evaluated as a replacement to the last peroxide stage of the D(EP)DP bleaching sequence and to the first peroxide stage of the D(EP)DP sequence, for an oxygen delignified eucalypt kraft-O(2) pulp. The P((SC-CO2)) stage was run with 0.5% hydrogen peroxide, at 15% consistency, 70 degrees C, and 73 bar. The reaction time was 30 min. The performances of regular P stages and the new P((SC-CO2)) stage were compared. Promising results were observed with the DEP((SC-CO2))DP sequence; the P((SC-CO2)) decreased kappa number from 2.7 to 2.1, and the hexenuronic acid groups from 17.0 to 12.4 mmol kg(-1). The P((SC-CO2)) stage showed poor performance when applied in the D(EP)DP((SC-CO2)) sequence. It is concluded that the process presents potential but requires further optimization to improve selectivity and efficiency.

Influence of hardwood, softwoodand fractionated pulp in a stratifiedthree-layered fine paper : Lövved, barrved och fraktionerad massa ochdess inverkan på ett treskiktat finpapper

Four different trials of stratified three-layered fine paper, of sulphate pulp, were performed to investigate if stratified fine fraction or fibres from birch can improve the properties of a paper compared to a reference sheet. All trials had five different scenarios and each scenario was calendered with different linear load. All sheets had a grammage of 80 g/m2.In the first trial, the paper contained birch, pine and filler of calciumcarbonate (marble), and was manufactured with the pilot paper machine XPM and the stratified headbox Formator at RCF (Stora Enso Research Center in Falun). The furnish consisted of 75% birch and 25% pine.The second trial contained coated sheets with paper from trial one as the base paper. The coating slip contained calciumcarbonate and clay and the amount was approximately 10-12 g/m2.The third trial, also with birch and pine but without filler, was performed at STFI (Skogsindustrins Tekniska Forskningsinstitut in Stockholm) with the laboratory scaled paper machine StratEx and the stratified headbox AQ-vanes. The furnish consisted of 75% birch and 25% pine, except for one scenario which contained of 75% pine and 25% birch.The last trial contained fractionated pulp of birch and pine and was performed at STFI. 50% was fine fraction and 50% was coarse fraction.This test does not show any clear benefits of making stratified sheets of birch and pine when it comes to properties such as bending stiffness, tensile index and surface smoothness. The retention can be improved with birch in the surface plies. It is possible that the formation can be improved with birch in the surface plies and pine in the middle ply. It is also possible that fine fraction in the surface plies and coarse fraction in the middle ply can improve both surface smoothness and bending stiffness. The results in this test are shown with confidence intervals which points out the difficulties of analysing sheets manufactured with a pilot paper machine or a laboratory scaled paper machine.

Comparative analysis of two selective bleaching methods on alpaca fibers

Dark brown Alpaca fiber was reduced in shade via selective bleaching with peroxide. Two selective oxidative bleaching methods were tested on alpaca top to assess their effectiveness for color removal and fiber quality properties. Color change, bundle strength, weight loss, fiber diameter, surface modification, dye-ability and dye wash fastness were assessed for both methods and compared with the original brown top. Bleach method 1 (BL-I) showed little surface modification, 5.8 % weight loss and 2.4 % strength loss. D1925 yellowness index was reduced to 74.3 from 83.1 and provided a good base for the dyeing of medium to deep shades. Bleach method 2 (BL-II) displayed considerable surface modification, 7.8 % weight loss and 18 % strength loss. BL-II also resulted in a mean diameter reduction of 1.9 micron during bleaching. Yellow-ness was reduced to 64.5 from 83.1 and provided a very good base for the dyeing of medium to deep shades. BL-I showed better exhaustion of the pre-metallised dye Lanaset Violet B than BL-II. Wash fastness for BL-II was 1 grey scale unit poorer than BL-I. BL-II showed far better color clarity at pale depths however the wash fastness of the finished product was not good enough to maintain the depth or clarity of the color. BL-I showed poorer clarity of color but exhibited better wash fastness results.

Effects of bleaching and dyeing on the quality of alpaca tops and yarns

This paper reports the effects of bleaching of alpaca tops and dyeing of bleached alpaca tops/yarns on the quality of tops and yarns. A dark brown alpaca top was bleached with hydrogen peroxide. Two bleaching methods were tried for effectiveness of color removal. A portion of each bleached top was dyed after bleaching. Color parameters were examined for unbleached, bleached and bleached/dyed tops, these tops were then converted into yarns of different twist levels and counts using a worsted spinning system. Some of the bleached yarn from each bleaching method was dyed in a package dye vat to compare the difference of top dyeing versus yarn package dyeing on yarn quality. Fiber diameter, yarn strength, yarn evenness, yarn hairiness and fiber degradation were tested to examine the effects of bleaching and dyeing on these properties at top and yarn stages. A processing route for bleaching and dyeing alpaca fiber was recommended.