Pontes integrais: estado da arte

Dissertação para obtenção do grau de mestre em Engenharia Civil

Esfuerzos inducidos en presas, arco-gravedad en operación por la acción térmica medioambiental : una aportación a su análisis y evaluación

Cyclic fluctuations of the atmospheric temperature on the dam site, of the water temperature in the reservoir and of the intensity of solar radiation on the faces of the dam cause significant stresses in the body of concrete dams. These stresses can be evaluated first by introducing in analysis models a linear temperature distribution statically equivalent to the real temperature distribution in the dam; the stress valúes obtained from this first step must be complemented (especially in the área of dam faces) with the stress valúes resuiting from the difference between the real temperature law and the linear law at each node. In the case of arch gravity dams, and because of their characteristics of arch dam featuring a thick section, both types of temperature-induced stresses are of similar importance. Thermal stress valúes are directly linked to a series of factors: atmospheric and water temperature and intensity of solar radiation at dam site, site latitude, azimuth of the dam, as well as geometrical characteristics of the dam and thermal properties of concrete. This thesis first presents a complete study of the physical phenomenon of heat exchange between the environment and the dam itself, and establishes the participation scheme of all parameters involved in the problem considered. A detailed documental review of available methods and techniques is then carried out both for the estimation of environmental thermal loads and for the evaluation of the stresses induced by these loads. Variation ranges are also established for the main parameters. The definition of the geometrical parameters of the dam is provided based on the description of a wide set of arch gravity dams built in Spain and abroad. As a practical reference of the parameters defining the thermal action of the environment, a set of zones, in which thermal parameters reach homogeneous valúes, was established for Spain. The mean valué and variation range of atmospheric temperature were then determined for each zone, based on a series of historical valúes. Summer and winter temperature increases caused by solar radiation were also defined for each zone. Since the hypothesis of thermal stratification in the reservoir has been considered, máximum and mínimum temperature valúes reached at the bottom of the reservoir were determined for each climatic zone, as well as the law of temperature variation in function of depth. Various dam-and-foundation configurations were analysed by means of finite element 3D models, in which the dam and foundation were each submitted to different load combinations. The seasonal thermal behaviour of sections of variable thickness was analysed through the application of numerical techniques to one-dimensional models. Contrasting the results of both analyses led to conclusions on the influence of environmental thermal action on the stress conditions of the structure. Las oscilaciones periódicas de la temperatura ambiente en el emplazamiento y de la temperatura del agua en el embalse, así como de la incidencia de la radiación solar sobre los paramentos de la presa, son causa de tensiones importantes en el cuerpo de las presas de hormigón. Estas tensiones pueden ser evaluadas en primer lugar introduciendo en los modelos tridimensionales de análisis, distribuciones lineales de temperatura estáticamente equivalentes a las correspondientes distribuciones reales en el cuerpo de la presa; las tensiones así obtenidas han de complementarse (sobre todo en las cercanías de los paramentos) con tensiones cuyo origen está en la temperatura diferencia entre la ley real y la lineal en cada punto. En el caso de las presas arco-gravedad y en razón de su doble característica de presas arco y de sección gruesa, ambas componentes de la tensión inducida por la temperatura son de magnitud similar. Los valores de estas tensiones de origen térmico están directamente relacionados con la temperatura del emplazamiento y del embalse, con la intensidad de la insolación, con la latitud y el azimut de la presa, con las características geométricas de la estructura y con las propiedades térmicas del hormigón. En esta tesis se realiza, en primer lugar, un estudio completo del fenómeno físico del intercambio de calor entre el medio ambiente y el cuerpo de la presa, estableciendo el mecanismo de participación de todos los parámetros que configuran el problema. En segundo lugar se realiza a cabo una revisión documental detallada de los métodos y técnicas utilizables tanto en la estimación de las cargas térmicas ambientales como en la evaluación de las tensiones inducidas por dichas cargas. En tercer lugar se establecen rangos de variación para los principales parámetros que configuran el problema. Los parámetros geométricos de la presa se definen a partir de la descripción de un amplio conjunto de presas arco-gravedad tanto españolas como del resto del mundo. Como referencia práctica de los parámetros que definen la acción térmica ambiental se establecen en España un conjunto de zonas caracterizadas por que, en cada una de ellas, los parámetros térmicos alcanzan valores homogéneos. Así, y en base a series de valores históricos, se establecen la media y la amplitud de la variación anual de la temperatura ambiental en cada una de las zonas. Igualmente, se han definido para cada zona los incrementos de temperatura que, en invierno y en verano, produce la insolación. En relación con el agua del embalse y en la hipótesis de estratificación térmica de este, se han definido los valores, aplicables en cada una de las zonas, de las temperaturas máxima y mínima en el fondo así como la ley de variación de la temperatura con la profundidad. Utilizando modelos tridimensionales de elementos finitos se analizan diferentes configuraciones de la presa y la cimentación sometidas, cada una de ellas, a diferentes combinaciones de carga. Aplicando técnicas numéricas a modelos unidimensionales se analiza el comportamiento térmico temporal de secciones de espesor variable. Considerando conjuntamente los resultados de los análisis anteriores se obtienen conclusiones parametrizadas de detalle sobre la influencia que tiene en el estado tensional de la estructura la consideración de la acción térmica ambiental.

Heat stress, heat strain, and productivity in Washington State tree fruit harvesters

Thesis (Master's)--University of Washington, 2016-06

Dimensionamento de um edifício destinado a centro de dia para idosos e creche

Trabalho de Projeto para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização em Estruturas

Thermal behaviour of corn starch granules under action of fungal alpha-amylase

Corn starch, partially hydrolyzed by fungal alpha-amylase was investigated by using thermal analysis, microscopy and X-ray diffraction. After enzymatic treatment lower degradation onset temperatures were observed. DSC analysis showed almost similar range of gelatinization temperature, however, the enthalpies of gelatinization increased for the partially hydrolyzed starch granules. According to the X-ray diffraction analysis, stronger cereal pattern peaks were recognized after enzymatic digestion. The results suggested that the hydrolysis was more pronounced in the amorphous part of the starch granules.

Temperature and thermal regime effects on the specific dynamic action of Bothrops alternatus (Serpentes, Viperidae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Action of Transition Metal Oxides on Composite Solid Propellants

The catalytic effects of Fe2O3, Ni2O3, MnO2, and Co2O3 transition metal oxides (TMO) on the combustion of polystyrene and carboxyl-terminated polybutadiene were investigated. The order of activity of TMO's was explained by the presence of Co and absence of Fe and Ni in their lattice systems along with a reduced electron-transfer process; in systems which induce the metal ions to enter the lattice, the electron transfer process is much greater. The thermal decomposition of ammonium perchlorate propellants was enhanced to a greater extent by Co2O3 and MnO2 than by Fe2O3 and Ni2O3.

The purification and properties of peroxidase in Mycobacterium tuberculosis H37Rv and its possible role in the mechanism of action of isonicotinic acid hydrazide

Peroxidase from Mycobacterium tuberculosis H37Rv was purified to homogeneity. The homogeneous protein exhibits catalase and Y (Youatt's)-enzyme activities in addition to peroxidase activity. Further confirmation that the three activities are due to a single enzyme was accomplished by other criteria, such as differential thermal inactivation, sensitivity to different inhibitors, and co-purification. The Y enzyme (peroxidase) was separated from NADase (NAD+ glycohydrolase) inhibitor by gel filtration on Sephadex G-200. The molecular weights of peroxidase and NADase inhibitor, as determined by gel filtration, are 240000 and 98000 respectively. The Y enzyme shows two Km values for both isoniazid (isonicotinic acid hydrazide) and NAD at low and high concentrations. Analysis of the data by Hill plots revealed that the enzyme has one binding site at lower substrate concentrations and more than one at higher substrate concentration. The enzyme contains 6g-atoms of iron/mol. Highly purified preparations of peroxidases from different sources catalyse the Y-enzyme reaction, suggesting that the nature of the reaction may be a peroxidatic oxidation of isoniazid. Moreover, the Y-enzyme reaction is enhanced by O2. Isoniazid-resistant mutants do not exhibit Y-enzyme, peroxidase or catalase activities, and do not take up isoniazid. The Y-enzyme reaction is therefore implicated in the uptake of the drug.

Cytotoxicity of half sandwich ruthenium(II) complexes with strong hydrogen bond acceptor ligands and their mechanism of action

Neutral and cationic organometallic ruthenium(II) piano stool complexes of the type [(eta(6)-cymene)R-uCl(X)(Y)] (complexes R1-R8) has been synthesized and characterized. In cationic complexes, X, Y is either a eta(2) phosphorus ligand such as 1,1-bis(diphenylphosphino)methane (DPPM) and 1,2-bis(diphenylphosphino)ethane (DPPE) or partially oxidized ligands such as 1,2-bis(diphenylphosphino)methane monooxide (DPPMO) and 1,2-bis(diphenylphosphino)ethane monooxide (DPPEO) which are strong hydrogen bond acceptors. In neutral complexes. X is chloride and Y is a monodentate phosphorous donor. Complexes with DPPM and DPPMO ligands ([(eta(6)-cymene)Ru(eta(2)-DPPM)Cl]PF6 (R2), [(eta(6)-cymene)Ru(eta(2)-DPPMO)Cl]PF6 (R3), [(eta(6)-cymene)Ru(eta(1)-DPPM)Cl-2] (R5) and [(eta(6)-cymene)Ru(eta(1)-DPPMO)Cl-2] (R6) show good cytotoxicity. Growth inhibition study of several human cancer cell lines by these complexes has been carried out. Mechanistic studies for R5 and R6 show that inhibition of cancer cell growth involves both cell cycle arrest and apoptosis induction. Using an apoptosis PCR array, we identified the sets of antiapoptotic genes that were down regulated and pro-apoptotic genes that were up regulated. These complexes were also found to be potent metastasis inhibitors as they prevented cell invasion through matrigel. The complexes were shown to bind DNA in a non intercalative fashion and cause unwinding of plasmid DNA in cell-free medium by competitive ethidium bromide binding, viscosity measurements, thermal denaturation and gel mobility shift assays.

Thermal ignition studies on metallized fuel-oxidizer systems

The thermal ignition behaviour of various mixtures of organic fuels, magnesium and ammonium nitrate (AN) has been examined by differential thermal analysis technique. It has been observed that the thermal decomposition/ignition of organic fuel-AN mixtures is modified significantly in the presence of magnesium metal. The decomposition characteristics of the binary mixtures of AN with various metals indicate the specific action of magnesium and zinc in lowering the decomposition temperature. A possible explanation for the low temperature decomposition is given in terms of the solid state reaction causing the fusion of AN which further reacts with the metal resulting in a highly exothermic reaction.

Morphology and thermal characteristics of nano-sized Pb-Sn inclusions in Al

Nanoembedded aluminum alloys with bimetallic dispersoids of Sn and Pb of compositions Sn-82-Pb-18,Pb- Sn-64-Pb-36, and Sn-54-Pb-46 were synthesized by rapid solidification. The two phases, face-centered-cubic Pb and tetragonal Sn solid-solution, coexist in all the particles. The crystallographic relation between the two phases and the matrix depends upon the solidification pathways adopted by the particles. For Al-(Sn-82-Pb-18), we report a new orientation relation given by [011]Al//[010]Sn and (011)Al//(101)Sn. Pb exhibits a cube-on-cube orientation with Al in few particles, while in others no orientation relationship could be observed. In contrast, Pb in Sn-64-Pb-36 and Sn-54-Pb-46 particles always exhibits cube-on-cube orientation with the matrix. Sn does not show any orientation relationship with Al or Pb in these cases. Differential scanning calorimetry studies revealed melting at eutectic temperature for all compositions, although solidification pathways are different. Attempts were made to correlate these with the melting and heterogeneous nucleation. characteristics.

Morphology and thermal characteristics of nano-sized Pb–Sn inclusions in Al

Nanoembedded aluminum alloys with bimetallic dispersoids of Sn and Pb of compositions Sn82–Pb18, Sn64–Pb36, and Sn54–Pb46 were synthesized by rapid solidification. The two phases, face-centered-cubic Pb and tetragonal Sn solid-solution, coexist in all the particles. The crystallographic relation between the two phases and the matrix depends upon the solidification pathways adopted by the particles. For Al–(Sn82–Pb18), we report a new orientation relation given by [011]Al//[010]Sn and (o11)A1//(101)Sn. Pb exhibits a cube-on-cube orientation with Al in few particles, while in others no orientation relationship could be observed. In contrast, Pb in Sn64–Pb36 and Sn54–Pb46 particles always exhibits cube-on-cube orientation with the matrix. Sn does not show any orientation relationship with Al or Pb in these cases. Differential scanning calorimetry studies revealed melting at eutectic temperature for all compositions, although solidification pathways are different. Attempts were made to correlate these with the melting and heterogeneous nucleation characteristics.

Electron Cyclotron Resonance in Strained Si and Si0.94Ge0.06 Channels on Relaxed Si0.62Ge0.38 Buffers Grown by Rapid Thermal Chemical Vapor Deposition

We report the far-infrared measurements of the electron cyclotron resonance absorption in n-type Si/Si0. 62Ge0.38 and Si0.94Ge0.06 /Si0. 62Ge0.38 modulation- doped heterostructures grown by rapid thermal chemical vapor deposition. The strained Si and Si0.94Ge0.06 channels were grown on relaxed Si0.62Ge0.38 buffer layers, which consist of 0.6 μm uniform Si0.62Ge0.38 layers and 0.5 μm compositionally graded relaxed SiGe layers from 0% Ge to 38 % Ge. The buffer layers were annealed at 800 °C for 1 hr to obtain complete relaxation. The samples had 100 Å spacers and 300 Å 2×1019 cm-3 n-type supply layers on the tops of the 75 Å channels. The far-infrared measurements of electron cyclotron resonance were performed at 4K with the magnetic field of 4 – 8 Tesla. The effective masses determined from the slope of center frequency of absorption peak vs applied magnetic field plot are 0.20 mo and 0.19 mo for the two dimensional electron gases in the Si and Si0.94Ge0.06 channels, respectively. The Si effective mass is very close to that of two dimensional electron gas in Si MOSFET (0.198mo). The electron effective mass of Si0.94Ge0.06 is reported for the first time and about 5 % lower than that of pure Si.