Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Estudio del efecto de la hidratación de la escoria blanca de acería de HEA: aplicación en pastas y morteros de cemento

xxiv, 252 p.

Avaliação do potencial remineralizante de pastas e soluções com compostos bioativos no esmalte dental bovino submetido a ciclos de desafio erosivo

O objetivo deste estudo foi avaliar in vitro por meio da Fluorescência de Raios X por Dispersão de Energia (XRF), Microdureza Vickers (MV) e Microscopia Eletrônica de Varredura (MEV) o efeito remineralizante de diferentes princípios bioativos, tais quais, nanopartículas de hidroxiapatita de cálcio (nanoHAp) associadas ou não a fluoreto, fosfopeptídeos de caseína do leite e fosfato de cálcio amorfo (CPP-ACP) associados ou não a fluoreto, fluoreto de sódio e saliva no esmalte dental bovino submetido a ciclagem des-remineralizante simulando lesão erosiva por alto desafio ácido. Foram obtidos 58 corpos de prova (CP) a partir de 58 incisivos bovinos que foram divididos aleatoriamente em 8 grupos, com 7 CP cada um e 2 CP para obtenção de imagem em MEV do esmalte hígido. Cada grupo foi denominado conforme os respectivos tratamentos a serem utilizados. Grupo 1 (G1) Controle; Grupo 2 (G2) Desensibilize Nano P experimental (nanopartículas de hidroxiapatita de cálcio); Grupo 3 (G3) Desensibilize Nano P (nanopartículas de hidroxiapatita de cálcio e flúor); Grupo4 (G4) GC Tooth Mousse (CPP-ACP, fosfopeptídios de caseína e fosfato de cálcio amorfo Recaldent ); Grupo 5 (G5) GC Tooth Mousse Plus (CPP-ACP, fosfopeptídios de caseína e fosfato de cálcio amorfo Recaldent + 900 ppm de flúor); Grupo 6 (G6) solução aquosa de fluoreto de sódio (0,05%); Grupo 7 (G7) solução aquosa de nanopartículas de hidroxiapatita de cálcio (0,375%) e Grupo 8 (G8) solução aquosa de nanopartículas de hidroxiapatita de cálcio (0,375%) + flúor (0,05%). Foram obtidos os valores de XRF e MV antes e depois do tratamento. Durante um período experimental de 10 dias, os CPs foram submetidos a um processo cíclico de des-remineralização incluindo vários ataques diários com ácido cítrico 0,05M (pH 2,3), 6 vezes de 2 minutos ao dia, bem como as aplicações das soluções teste e períodos de remineralização em saliva artificial. O tempo entre os ciclos era de 1,5 h. Foram obtidas imagens em MEV para análise da superfície após o tratamento. Através da análise estatística pelo teste t student (p = 0,05), foram encontrados os seguintes resultados: o grupo controle teve uma desmineralização considerada severa; houve aumento na contagem de P em todos os grupos que receberam tratamento, exceto o G1, igualando ou até mesmo aumentando no caso do G5, em relação a contagem inicial; houve aumento na contagem de Ca em todos os grupos que receberam tratamento, exceto no G1, igualando ou até mesmo aumentando no caso do G4, em relação a contagem inicial; houve perda de microdureza superficial em todos os grupos; o G7 teve comportamento similar ao G1 e o G3 teve comportamento inferior ao G5 em relação ao P. E todos os outros grupos tiveram comportamento superior ao controle; o G4 e o G5 tiveram um comportamento superior ao G2 em relação ao Ca. O G5 teve comportamento superior ao G3 também em relação ao Ca e todos os grupos foram superiores ao controle; o G7 teve comportamento similar ao controle em relação a microdureza superficial e todos os outros grupos foram superiores ao controle.

Informe del taller de capacitación en pastas, engobes, vidriados y aplicación de los mismos.

36 hojas.

Cerámica en la Capilla, Belén y Oicata : asesoria en diseño, desarrollo de producto, pastas y hornos, etiquetas y empaques.

96 hojas : ilustraciones, fotografías a color.

Elaboración experimental de pastas de merluza (Merluccius gayi peruanus) y productos derivados

Describe la tecnología experimental de elaboración de pastas y queques de merluza (Merluccius gayi peruanus). Se analiza la materia prima empleada, el rendimiento, calidad de productos y el costo estimado de producción experimental.

Reorganización del área de producción en la Fábrica de Galletas y Pastas Martínez, S.A. asesoría correctiva [por] Nicolás Alberto Gálvez Molina

Tesis (Maestría en Ciencias de la Administración con especialidad en Producción) U.A.N.L.

Estudio del proceso de hidratación de pastas de cemento portland reemplazadas con escoria granulada de alto horno, ceniza volante y metacaolín, utilizando dos aditivos superplastificantes.

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) UANL, 2011.

Adição de óxido de zinco (ZnO) em pastas de cimento visando viabilizar a reciclagem de pós de aciaria elétrica (PAE) na construção civil

O Pó de Aciaria Elétrica (PAE) é um resíduo sólido perigoso gerado durante o processo de fabricação do aço. Devido ao grande volume gerado, de 12 a 14 kg por tonelada de aço fabricado, faz-se necessário o estudo de alternativas de reciclagem do mesmo. A caracterização química, física e de fases é etapa fundamental para avaliar a viabilidade de reciclagem deste resíduo. Uma das alternativas de reciclagem do PAE é a adição deste resíduo na fabricação de artefatos para a construção civil. Entretanto, esta adição retarda o início das reações de hidratação dos artefatos, dificultando seu uso. Esse retardo é atribuído aos compostos de zinco (Zn) presentes no resíduo. Este trabalho foi desenvolvido em duas etapas. Na primeira etapa foi realizada a caracterização química, física e de fases. Os resultados analíticos indicam que o PAE possui um tamanho médio de partícula que possibilita sua adição na produção de artefatos de cimento. Em relação às fases cristalinas as amostras de PAE estudadas contêm: ZnFe2O4, Fe3O4, FeCr2O4, Ca0,15Fe2,85O4, SiO2 e ZnO. Na segunda etapa deste trabalho, o ZnO, uma das formas cristalinas do Zn detectadas no PAE, foi adicionado em pastas de cimento. O objetivo desta etapa foi estudar os fenômenos relacionados ao início das reações de hidratação destas pastas. Essas amostras foram analisadas via Difração de Raios-X (DRX), Microscopia Eletrônica de Varredura (MEV) e mapeamento por raios-x característicos em diferentes idades (1, 2, 4, 7 e 14 dias), a fim de rastrear os fenômenos ocorridos durante a hidratação das pastas de cimento Os resultados obtidos nesta segunda etapa indicam que no primeiro momento antes da hidratação (1 dia) o Zn apresentava-se na forma de ZnO. A partir do quarto dia observa-se a formação de uma nova fase contendo Zn: CaZn2(OH)6 . 2H2O e, sugerindo a transição de Zn na forma de óxido para hidróxido. Isto se torna mais evidente no sétimo dia, onde é possível constatar que as reações de hidratação aconteceram (pasta totalmente endurecida), pois neste caso, o Zn é encontrado somente na forma de hidróxido. A formação do composto CaZn2(OH)6 . 2H2O permite que as reações de hidratação da pasta de cimento contendo Zn sejam efetivadas. O trabalho finaliza com a apresentação de um modelo onde se busca explicar o fenômeno observado durante a execução do mesmo.

Adição de superplastificante e anti-segregante à base de CMC em pastas de cimento para Poços de Petróleo

Oil well cementing materials consist of slurries of Special class Portland cement dispersed in water. Admixtures can be used to provide the necessary fluidity, so the material can be efficiently pumped down as well as penetrate porous rocks with controlled filter loss. Construction admixtures can be used to modify the properties of oil well cements provided they can withstand and hold their properties at the higher than ambient temperatures usually encountered in oil fields. In civil construction, superplasticizer play the role of dispersants that reduce the facto r of water cement improve mechanical properties and fluidity of the cement, whereas anti-segregation agents improve the workability of the slurry. In the present study, oil well cement slurries were produced adding both a dispersant and an anti-segregation agent conventionally used in Portland CPII-Z-32 RS cement aiming at materials for primary cementing and squeeze operations. Three basic aspects were evaluated: fluidity, filter loss and the synergetic effect of the admixtures at two temperatures, i.e., 27°C and 56°C, following API RP 10B practical recommendations. The slurries were prepared using admixture concentrations varying from 2.60 Kgf/m3 (0.02 gallft3) to 5.82 Kgf/m3 (0.045 galJft3) BWOC. The density of the slurries was set to 1.89 g/cm3 (15.8 Ib/gal). 0.30 to 0.60% BWOC of a CMC-based anti-segregation agent was added to the cement to control the filter loss. The results showed that the addition of anti-segregation at concentrations above 0.55% by weight of cement resulted in the increased viscosity of the folders in temperatures evaluated. The increasing the temperature of the tests led to a reduction in the performance of anti-segregation. At concentrations of 5.20 kgf/m3 (0,040 gallft3) and 5.82 Kgf/m3 (0,045 gal/ft 3) observed a better performance of the properties evaluated in the proposed system. At low temperature was observed instability in the readings of rheology for all concentrations of anti-segregation. Contents that increasing the concentration of anti¬-segregation is limited concentrations greater than 0.55 % BWOC of the CMC in temperature analyzed. The use of the system with CMC promoted a good performance against the properties evaluated. The principal function of anti¬-segregation was optimized with increasing concentration of superplasticizer, at temperatures above the 2rC. The study of the behaviour of systemic additives, resulting in slurries of cement, which can be optimized face studies of other intrinsic properties in oil fields

Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration

Análise do comportamento reológico de pastas de cimento contendo resíduos de pneu para poços de petróleo

The low tenacity presented by the Portland cement pastes used in the oil wells cementation has been motivating several researches with attention focused on alternative materials. Additives have been developed to generate flexible pastes with mechanical resistance capable to support the expansions and retractions of the metallic covering of the wells that submit to the steam injection, technique very used to increase the recovery factor in oil reservoirs with high viscosity. A fresh paste with inadequate rheological behavior may commit the cementation process seriously, involving flaws that affect the performance of the paste substantially in the hardened state. This work proposes the elaboration and the rheological analysis of Portland cement pastes with addition of residues of rubber tire in several proportions, with the aim of minimizing the damages provoked in the hem cementing of these wells. By thermogravimetric analysis, the particles of eraser that go by the sieve of 0,5mm (35 mesh) opening and treated superficially with NaOH solution of 1 mol/L presented appropriate thermal resistance for wells that submit to thermal cyclic. The evaluation of the study based on the results of the rheological analysis of the pastes, complemented by the mechanical analysis, thickening, stability, tenor of free water and filtrate loss, being used as parameter a paste reference, without rubber addition. The results showed satisfactory rheology, passive of few corrections; considerable loss of mechanical resistance (traction and compression), compensated by earnings of tenacity, however with established limits for its application in oil wells; satisfactory stability, free water and thickening time

Adição de vermiculita expandida mícron em pastas de baixa densidade para cimentação de poços de petróleo

The northeastern region of Brazil has a large number of wells producing oil using a method of secondary recovery steam injection, since the oil produced in this region is essentially viscous. This recovery method puts the cement / coating on thermal cycling, due to the difference in coefficient of thermal expansion between cement and metal coating causes the appearance of cracks at this interface, allowing the passage of the annular fluid, which is associated with serious risk socioeconomic and environmental. In view of these cracks, a correction operation is required, resulting in more costs and temporary halt of production of the well. Alternatively, the oil industry has developed technology for adding new materials in cement pastes, oil well, providing high ductility and low density in order to withstand the thermo-mechanical loads generated by the injection of water vapor. In this context, vermiculite, a clay mineral found in abundance in Brazil has been applied in its expanded form in the construction industry for the manufacture of lightweight concrete with excellent insulation and noise due to its high melting point and the presence of air in their layers lamellar. Therefore, the vermiculite is used for the purpose of providing low-density cement paste and withstand high temperatures caused by steam injection. Thus, the present study compared the default folder containing cement and water with the folders with 6%, 8% and 10% vermiculite micron conducting tests of free water, rheology and compressive strength where it obtained the concentration of 8 % with the best results. Subsequently, the selected concentration, was compared with the results recommended by the API standard tests of filtered and stability. And finally, analyzed the results from tests of specific gravity and time of thickening. Before the study we were able to make a folder with a low density that can be used in cementing oil well in order to withstand the thermo-mechanical loads generated by steam injection

Avaliação da influência do nacl em pastas de cimento portland para cimentação de poços de petróleo em zonas evaporíticas

One of the major current challenges for oilwell companies is the extraction of oil from evaporitic zones, also known as pre-salt basins. Deep reservoirs are found under thick salt layers formed from the evaporation of sea water. Salt layers seal the flow of oil from underneath rock formations, which store hydrocarbons and increase the probability of success in oil and gas exploration. Oilwells are cemented using Portland-based slurries to promote mechanical stability and zonal isolation. For pre-salt oilwells, NaCl must be added to saturate the cement slurries, however, the presence of salt in the composition of slurries affects their overall behavior. Therefore, the objective of the present study was to evaluate the effect of the addition of 5 to 25% NaCl on selected properties of Portland-based slurries. A series of tests were carried out to assess the rheological behavior, thickening time, free water and ultrassonic compressive strength. In addition, the slurries were also characterized by thermal analysis, X ray diffraction and scanning electron microscopy. The results showed that the addition of NaCl affected the thickening time of the slurries. NaCl contents up to 10% shortened the thickening time of the slurries. On the other hand, concentrations in excess of 20% not only extended the thickening time, but also reduced the strength of hardened slurries. The addition of NaCl resulted in the formation of a different crystalline phase called Friedel´s salt, where free chlorine is bonded to tricalcium aluminate