ESEM study of illite/smectite freshwater sensitivity in sandstone reservoirs

The water sensitivity of authigenic smectite- and illite-rich illite/smectites in sandstone reservoirs has been investigated using an Environmental Scanning Electron Microscope (ESEM). The ESEM enabled the illite/smectites to be directly observed in situ at high magnification during freshwater immersion, and was also particularly effective in allowing the same selected illite/smectite areas to be closely compared before and after freshwater treatments. The tendency of authigenic smectite-rich illite/smectite to swell on contact with fresh water varies greatly. Smectite-rich illite/smectite may osmotically swell to many times its original volume to form a gel which greatly reduces porosity and permeability, or may undergo only a subtle morphological change which has little or no adverse effect on reservoir quality. Authigenic illite-rich illite/smectite in sandstones does not swell when immersed in fresh water. Even after prolonged soaking in fresh water, illite-rich illite/smectite particles retain their original morphology. Accordingly, illite-rich illite/smectite in sandstones is unlikely to cause formation damage if exposed to freshwater-based fluids. © 1993.

Volcanic stratigraphy, alteration zoning, and vein paragenesis of the Sascha-Pelligrini low-sulphidation epithermal system, Santa Cruz, Argentina

The Sascha-Pelligrini low-sulphidation epithermal system is located on the western edge of the Deseado Massif, Santa Cruz Province, Argentina. Outcrop sampling has returned values of up to 160g/t gold and 796g/t silver, with Mirasol Resources and Coeur D.Alene Mines currently exploring the property. Detailed mapping of the volcanic stratigraphy has defined three units that comprise the middle Jurassic Chon Aike Formation and two units that comprise the upper Jurassic La Matilde Formation. The Chon Aike Formation consists of rhyodacite ignimbrites and tuffs, with the La Matilde Formation including rhyolite ash and lithic tuffs. The volcanic sequence is intruded by a large flow-banded rhyolite dome, with small, spatially restricted granodiorite dykes and sills cropping out across the study area. ASTER multispectral mineral mapping, combined with PIMA (Portable Infrared Mineral Analyser) and XRD (X-ray diffraction) analysis defines an alteration pattern that zones from laumontite-montmorillonite, to illite-pyritechlorite, followed by a quartz-illite-smectite-pyrite-adularia vein selvage. Supergene kaolinite and steam-heated acid-sulphate kaolinite-alunite-opal alteration horizons crop out along the Sascha Vein trend and Pelligrini respectively. Paragenetically, epithermal veining varies from chalcedonic to saccharoidal with minor bladed textures, colloform/crustiform-banded with visible electrum and acanthite, crustiform-banded grey chalcedonic to jasperoidal with fine pyrite, and crystalline comb quartz. Geothermometry of mineralised veins constrains formation temperatures from 174.8 to 205.1¡ÆC and correlates with the stability field for the interstratified illite-smectite vein selvage. Vein morphology, mineralogy and associated alteration are controlled by host rock rheology, permeability, and depth of the palaeo-water table. Mineralisation within ginguro banded veins resulted from fluctuating fluid pH associated with selenide-rich magmatic pulses, pressure release boiling and wall-rock silicate buffering. The study of the Sascha-Pelligrini epithermal system will form the basis for a deposit-specific model helping to clarify the current understanding of epithermal deposits, and may serve as a template for exploration of similar epithermal deposits throughout Santa Cruz.

Fresh water and acid sensitivity of authigenic clays in sandstone reservoirs

Authigenic illite-smectite and chlorite in reservoir sandstones from several Pacific rim sedimentary basins in Australia and New Zealand have been examined using an Electroscan Environmental Scanning Electron Microscope (ESEM) before, during, and after treatment with fresh water and HCl, respectively. These dynamic experiments are possible in the ESEM because, unlike conventional SEMs that require a high vacuum in the sample chamber (10-6 torr), the ESEM will operate at high pressures up to 20 torr. This means that materials and processes can be examined at high magnifications in their natural states, wet or dry, and over a range of temperatures (-20 to 1000 degrees C) and pressures. Sandstones containing the illite-smectite (60-70% illite interlayers) were flushed with fresh water for periods of up to 12 hours. Close examination of the same illite-smectite lines or filled pores, both before and after freshwater treatments, showed that the morphology of the illite-smectite was not changed by prolonged freshwater treatment. Chlorite-bearing sandstones (Fe-rich chlorite) were reacted with 1M to 10M HCl at temperatures of up to 80 degrees C and for periods of up to 48 hours. Before treatment the chlorites showed typically platy morphologies. After HCl treatment the chlorite grains were coated with an amorphous gel composed of Ca, Cl, and possibly amorphous Si, as determined by EDS analyses on the freshly treated rock surface. Brief washing in water removed this surface coating and revealed apparently unchanged chlorite showing no signs of dissolution or acid attack. However, although the chlorite showed no morphological changes, elemental analysis only detected silicon and oxygen.

Imaging fluid solid interactions in hydrocarbon reservoir rocks

The environmental scanning electron microscope (ESEM) has been used to image liquid hydrocarbons in sandstones and oil shales. Additionally, the fluid sensitivity of selected clay minerals in hydrocarbon reservoirs was assessed via three case studies: HCl acid sensitivity of authigenic chlorite in sandstone reservoirs, freshwater sensitivity of authigenic illite/smectite in sandstone reservoirs, and bleach sensitivity of a volcanic reservoir containing abundant secondary chlorite/corrensite. The results showed the suitability of using ESEM for imaging liquid hydrocarbon films in hydrocarbon reservoirs and the importance of simulating in situ fluid-rock interactions for hydrocarbon production programmes. In each case, results of the ESEM studies greatly enhanced prediction of reservoir/borehole reactions and, in some cases, contradicted conventional wisdom regarding the outcome of potential engineering solutions. (C) 1993 Wiley-Liss, Inc.

High-resolution imaging of ordered mixed-layer clays

HRTEM has been used to examine illite/smectite from the Mancos shale, rectorite from Garland County, Arkansas; illite from Silver Hill, Montana; Na-smectite from Crook County, Wyoming; corrensite from Packwood, Washington; and diagenetic chlorite from the Tuscaloosa formation. Thin specimens were prepared by ion milling, ultra-microtome sectioning and/or grain dispersal on a porous carbon substrate. Some smectite-bearing clays were also examined after intercalation with dodecylamine hydrochloride (DH). Intercalation of smectite with DH proved to be a reliable method of HRTEM imaging of expanded smectite, d(001) 16 A which could then be distinguished from unexpanded illite, d(001) 10 A. Lattice fringes of basal spacings of DH-intercalated rectorite and illite/smectite showed 26 A periodicity. These data support XRD studies which suggest that these samples are ordered, interstratified varieties of illite and smectite. The ion-thinned, unexpanded corrensite sample showed discrete crystallites containing 10 A and 14 A basal spacings corresponding with collapsed smectite and chlorite, respectively. Regions containing disordered layers of chlorite and smectite were also noted. Crystallites containing regular alternations of smectite and chlorite were not common. These HRTEM observations of corrensite did not corroborate XRD data. Particle sizes parallel to the c axis ranged widely for each sample studied, and many particles showed basal dimensions equivalent to > five layers. -J.M.H.

Caracterização e desenvolvimento de argilas para aplicação em nanocompósitos poliméricos

O Brasil é produtor de argilas e conta com grandes reservas deste recurso natural. Porém, grande parte da sua produção é comercializada seca e moída. O desenvolvimento de argilas para seu uso como reforço em nanocompósitos poliméricos constitui uma opção para os produtores desta matéria prima que teriam assim um produto com maior valor agregado. Este trabalho visa avaliar o potencial uso como nanocarga de duas argilas nacionais provenientes da Bacia de Taubaté, São Paulo, denominadas ALIGRA e SANTA FÉ. As frações de tamanho de partícula médio menor de 0,02 mm, obtidas por peneiramento á úmido da argila homogeneizada e seca, foram utilizadas no desenvolvimento do trabalho experimental. Os estudos de caracterização, envolvendo análise granulométrica, química, mineralógica, morfológica, térmica e textural, revelaram características muito semelhantes em ambas às argilas. Fração argila, maior de 70% em massa. Composição química conforme a definição química de uma argila e os teores de seus componentes mostram valores intermédios entre as apresentadas pelas bentonitas e argila caulinítica usadas com fins de comparação. Ressaltamse boas propriedades adsorventes. Área superficial específica BET ao redor de 120 m2/g, valor maior do que o apresentado por muitas bentonitas naturais (74,5 m2/g). Predominantemente mesoporosas, com poros, maiormente em forma de fenda, característicos da estrutura em camadas das argilas. Baixa capacidade de troca catiônica, 12 meq/100g. Difratogramas de raios-X revelaram a predominância do estratificado ilita/esmectita, caulinita e quartzo na argila ALIGRA, e de ilita, caulinita e quartzo na argila SANTA FÉ. Prosseguiu-se com a argila ALIGRA a preparação da argila organofílica. A argila organofílica foi obtida por troca catiônica com o sal quaternário de amônio: cloro cetril trimetil amônio, depois de homogeneizada em sódio com cloreto de sódio. Análises FTIR e TGA indicaram que houve inserção dos cátions orgânicos. Testes preliminares foram feitas, preparando misturas das argilas com matriz de polipropileno e usando como agente compatibilizante polipropileno enxertado com anidrido maleico. Resultados de ensaios de tração reportam algumas melhoras nas propriedades testadas com as composições preparadas com as argilas purificadas. Com as composições com argilas organofílicas somente foi melhorado o alongamento na rotura. Estudos ais aprofundados são recomendados.

东南极格罗夫山地区的土壤特征及其环境研究

The Grove Mountains, including 64 nunataks, is situated on an area about 3200km2 in the inland ice cap of east Antarctica in Princess Elizabeth land (72o20'-73°101S, 73°50'-75o40'E), between Zhongshan station and Dome A, about 450km away from Zhongshan station (69°22'S, 76°22'E). Many workers thought there was no pedogenesis in the areas because of the less precipitation and extreme lower temperature. However, during the austral summer in 1999-2000, the Chinaer 16 Antarctic expedition teams entered the inland East Antarctica and found three soil spots in the Southern Mount Harding, Grove Mountains, East Antarctica. It is the first case that soils are discovered in the inland in East Antarctica. Interestingly, the soils in this area show clay fraction migration, which is different from other cold desert soils. In addition, several moraine banks are discovered around the Mount Harding. The soil properties are discussed as below. Desert pavement commonly occurs on the three soil site surfaces, which is composed of pebbles and fragments formed slowly in typical desert zone. Many pebbles are subround and variegated. These pebbles are formed by abrasion caused by not only wind and wind selective transportation, but also salt weathering and thaw-freezing action on rocks. The wind blows the boulders and bedrocks with snow grains and small sands. This results in rock disintegration, paved on the soil surface, forming desert pavement, which protects the underground soil from wind-blow. The desert pavement is the typical feature in ice free zone in Antarctica. There developed desert varnish and ventifacts in this area. Rubification is a dominant process in cold desert Antarctic soils. In cold desert soils, rubification results in relatively high concentrations of Fed in soil profile. Stained depth increases progressively with time. The content of Fed is increasing up to surface in each profile. The reddish thin film is observed around the margin of mafic minerals such as biotite, hornblende, and magnetite in parent materials with the microscope analyzing on some soil profiles. So the Fed originates from the weathering of mafic minerals in soils. Accumulations of water-soluble salts, either as discrete horizons or dispersed within the soil, occur in the soil profiles, and the salt encrustations accumulate just beneath surface stones in this area. The results of X-ray diffraction analyses show that the crystalline salts consist of pentahydrite (MgSO4-5H2O), hexahydrite (MgSO4-6H2O), hurlbutite (CaBe2(PO4)2), bloedite (Na2Mg(S04)2-4H2O), et al., being mainly sulfate. The dominant cations in 1:5 soil-water extracts are Mg2+ and Na+, as well as Ca2+ and K+, while the dominant anion is SO42-, then NO3-, Cl- and HCO3-. There are white and yellowish sponge materials covered the stone underside surface, of which the main compounds are quartz (SiO2, 40.75%), rozenite (FeSOKkO, 37.39%), guyanaite (Cr2O3-1.5H2O, 9.30%), and starkeyite (MgSO4-4H2O, 12.56%). 4) The distribution of the clay fraction is related to the maximum content of moisture and salts. Clay fraction migration occurs in the soils, which is different from that of other cold desert soils. X-ray diffraction analyses show that the main clay minerals are illite, smectite, then illite-smectite, little kaolinite and veirniculite. Mica was changed to illite, even to vermiculite by hydration. Illite formed in the initial stage of weathering. The appearance of smectite suggests that it enriched in magnesium, but no strong eluviation, which belongs to cold and arid acid environment. 5) Three soil sites have different moisture. The effect moisture is in the form of little ice in site 1. There is no ice in site 2, and ice-cement horizon is 12 cm below the soil surface in site 3. Salt horizon is 5-10 cm up to the surface in Site 1 and Site 2, while about 26cm in site 3. The differentiation of the active layer and the permafrost are not distinct because of arid climate. The depth of active layer is about 10 cm in this area. Soils and Environment: On the basis of the characteristics of surface rocks, soil colors, horizon differentiation, salt in soils and soil depth, the soils age of the Grove Mountains is 0.5-3.5Ma. No remnants of glaciations are found on the soil sites of Mount Harding, which suggests that the Antarctic glaciations have not reached the soil sites since at least 0.5Ma, and the ice cap was not much higher than present, even during the Last Glacial Maximum. The average altitude of the contact line of level of blue ice and outcrop is 2050m, and the altitude of soil area is 2160m. The relative height deviation is about 110m, so the soils have developed and preserved until today. The parental material of the soils originated from alluvial sedimentary of baserocks nearby. Sporepollen were extracted from the soils, arbor pollen grains are dominant by Pinus and Betula, as well as a small amount Quercus, Juglans, Tilia and Artemisia etc. Judging from the shape and colour, the sporepollen group is likely attributed to Neogene or Pliocene in age. This indicates that there had been a warm period during the Neogene in the Grove Mountains, East Antarctica.

大方不规则I/S间层的铝层柱化研究

层柱粘土是一类新型的矿物功能材料,具有大孔径、大比表面积、孔径可调、热稳定性好、表面酸性强及含有金属活性组分等特点.它是当前国际粘土矿物学、化学及材料科学界研究的一个热点.该文以贵州大方猫场不规则伊/蒙（简称I/S）间层为研究对象,利用聚合羟基铝作为柱化剂对其进行了层柱化研究,系统地介绍了大方不规则I/S间层的矿物学特征、柱化剂Al<,13>的形态特征、铝层柱I/S间层的制备及表征等.

伊/蒙不规则间层粘土的矿物学特征及其层柱化研究

该文首先详细而系统地介绍了一类新型纳米矿物材料——层柱粘土.论文以贵州大方I/S不规则有序间层粘土为例,在采用多种测试手段了解该矿物的组成、结构及性能的基础上,首次对I/S不规则间层粘土进行了较系统的铝、锆、钛的层柱化研究.XRD、HRTEM、FTIR及DTA-TG共同揭示了大方I/S间层粘土是以Rl型为主的I/S不规则有序间层粘土,化学分析数据计算表明结构中的八面体为二八面体,蒙皂石为钠型蒙脱石.通过对大方I/S不规则间层粘土的铝层柱研究发现,较低的初始铝浓度有利于形成较多的Keggin离子,产物层间距可达3.2～3.5nm,N<,2-BET比表面积达110m<'2>/g.首次对I/S不规则间层粘土进行了钻、钛层柱化研究,所获产物层间距都大于铝层柱者,分别为3.3～4.0nm和3.5~4.7nm.文章首次对层柱I/S不规则间层粘土进行了除层间距以外的孔结构、表面酸性、(水)热稳定性和显微形貌的表征.探讨了层与柱之间、颗粒与颗粒之间的排列和连接对层柱产物性能的影响,比较成功地用IR证据解释了层在机理中四面体的反转问题.最后初步试验了层柱I/S不规则间层粘土对水中重金属pb<'2+>和垃圾淋滤液中COD的去除效果,结果表明卫Ti-I/S对Pb<'2+>的吸附容量可达8.39mg/g,对COD的去除率可高达76.71%.

A new data set of soil mineralogy for dust-cycle modeling

The mineralogy of airborne dust affects the impact of dust particles on direct and indirect radiative forcing, on atmospheric chemistry and on biogeochemical cycling. It is determined partly by the mineralogy of the dust-source regions and partly by size-dependent fractionation during erosion and transport. Here we present a data set that characterizes the clay and silt-sized fractions of global soil units in terms of the abundance of 12 minerals that are important for dust–climate interactions: quartz, feldspars, illite, smectite, kaolinite, chlorite, vermiculite, mica, calcite, gypsum, hematite and goethite. The basic mineralogical information is derived from the literature, and is then expanded following explicit rules, in order to characterize as many soil units as possible. We present three alternative realizations of the mineralogical maps, taking the uncertainties in the mineralogical data into account. We examine the implications of the new database for calculations of the single scattering albedo of airborne dust and thus for dust radiative forcing.

Diagênese da Formação Corumbataí na Mina Partezani, Rio Claro - SP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Mineralogia e geoquímica da ocorrência de palygorskita de Alcântara, bacia de S. Luís-Grajaú, Maranhão

A Formação Alcântara (bacia de São Luis-Grajaú, região de Alcântara, MA) é constituída por pelitos, arenitos e dolomitos. Esses litotipos representam uma sucessão progradacional de depósitos de laguna/washover e canal de maré sobrepondo-se a depósitos de shoreface gerados por processos de tempestade. O presente trabalho tem como objetivo principal à caracterização mineralógica e geoquímica dos argilominerais que ocorrem nos níveis pelíticos da Formação Alcântara, especialmente a palygorskita. Foi descrito e amostrado um perfil geológico na praia da Baronesa, na cidade de Alcântara, MA, no qual foram coletadas 8 amostras, que após a preparação em laboratório, foram submetidas a análises mineralógicas e químicas por difração de raios X, fluorescência de raios X, análises térmicas e microscopia eletrônica de varredura. Os resultados mostraram que o perfil da praia da Baronesa é composto por arenitos na base, seguido de pelitos dominantes, com intercalações de dolomitos. Nos pelitos, foram descritos uma ampla assembléia de argilominerais, em ambiente lagunar, com variações no conteúdo de palygorskita, clorita, illita, esmectita e traços de caulinita. Observam-se ainda traços de dolomita, calcita e feldspatos. Os teores de palygorskita e dolomita (níveis dolomíticos) são acentuados, sugerindo que as condições climáticas durante o período de deposição foram áridas a semi-áridas. Duas gerações de palygorskita foram descritas: uma na forma de bolsões ou acumulações macroscópicas nos níveis pelíticos ricos em esmectita, freqüentemente descritas na literatura, e outra na forma maciça, como o mineral dominante dos níveis pelíticos superiores do perfil da praia da Baronesa. Essa segunda geração está sendo descrita pela primeira vez, neste trabalho, podendo constituir em níveis métricos e que podem revelar interesse econômico.