357 resultados para Formiga


Relevância:

10.00% 10.00%

Publicador:

Resumo:

The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Efforts in research and development of new technologies to reduce emission levels of pollutant gases in the atmosphere has intensified in the last decades. In this context, it can be highlighted the modern systems of electronic engine management, new automotive catalysts and the use of renewable fuels which contributes to reduce the environmental impact. The purpose of this study was a comparative analysis of gas emissions from a automotive vehicle, operating with different fuels: natural gas, AEHC or gasoline. To execute the experimental tests, a flex vehicle was installed on a chassis dynamometer equipped with a gas analyzer and other complementary accessories according to the standard guidelines of emission and security procedures. Tests were performed according to NBR 6601 and NBR 7024, which define the urban and road driving cycle, respectively. Besides the analysis of exhaust gases in the discharge tube, before and after the catalyst, using the suction probe of the gas analyzer to simulate the vehicle in urban and road traffic, were performed tests of fuel characterization. Final results were conclusive in indicating leaded gasoline as the fuel which most contributed with pollutant emissions in atmosphere and the usual gasoline being the fuel which less contributed with pollutant emissions in atmosphere

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

In a hospital environment, these bacteria can be spread by insects such as ants, which are characterized by high adaptability to the urban environment. Staphylococcus is a leading cause of hospital infection. In Europe, Latin America, USA and Canada, the group of coagulase negative staphylococci (CoNS) is the second leading cause of these infections, according to SENTRY (antimicrobial surveillance program- EUA). In this study, we investigated the potential of ants (Hymenoptera: Formicidae) as vehicle mechanics of Staphylococcus bacteria in a public hospital, in Natal-RN. The ants were collected, day and night, from June 2007 to may 2008, in the following sectors: hospitals, laundry, kitchen, blood bank. The ants were identified according to the identification key of Bolton, 1997. For the analysis of staphylococci, the ants were incubated in broth Tryptic Soy Broth (TSB) for 24 hours at 35 º C and then incubated on Mannitol Salt Agar. The typical colonies of staphylococci incubated for 24 hours at 35 ° C in Tryptic Soy Agar for the characterization tests (Gram stain, catalase, susceptibility to bacitracin and free coagulase). The identification of CoNS was performed through biochemical tests: susceptibility to novobiocin, growth under anaerobic conditions, presence of urease, the ornithine decarboxylation and acid production from the sugars mannose, maltose, trehalose, mannitol and xylose. The antimicrobial susceptibility examined by disk-diffusion technique. The technique of Polymerase Chain Reaction was used to confirm the presence of mecA gene and the ability to produce biofilm was verified by testing in vitro using polystyrene inert surface, in samples of resistant staphylococci. Among 440 ants, 85 (19.1%) were carrying coagulase-negative staphylococci (CoNS) of the species Staphylococcus saprophyticus (17), Staphylococcus epidermidis (15), Staphylococcus xylosus (13), Staphylococcus hominis hominis (10), Staphylococcus lugdunensis (10), Staphylococcus warneri (6), Staphylococcus cohnii urealyticum (5), Staphylococcus haemolyticus (3), Staphylococcus simulans (3), Staphylococcus cohnii cohnii (2), and Staphylococcus capitis (1). No Staphylococcus aureus was found. Among the isolates, 30.58% showed resistance to erythromycin. Two samples of CoNS (2.35%), obtained from the ant Tapinoma melanocephalum collected in the post-surgical female ward, S. Hominis hominis and S. lugdunensis harbored the mecA gene and were resistant to multiple antibiotics, and the specie S. hominis hominis even showed to be a biofilm producer. This study proves that ants act as carriers of multidrug-resistant coagulase-negative Staphylococci and biofilm producers and points to the risk of the spreading of pathogenic microorganisms by this insect in the hospital environment

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The relationship between lipid peroxidation, antioxidant defense and diabetic osteopenia remains unclear. This study evaluated the relationship between lipid peroxidation index, antioxidant defense parameter and bone metabolism in a premenopausal diabetic model by measurements such as thiobarbituric acid-reactive substances concentration (TBARS) and reduced glutathione (GSH) content in brain homogenates, histomorphometric analysis, biomechanical testing and bone mineral density (BMD). Female Wistar rats with regular estrous cycle were divided into two groups: Group 1: control rats (n = 15) and Group 2: diabetic rats (n = 15). Diabetes mellitus was induced by alloxan and confirmed by glycemia 250 mg/dL. The experimental period understood 1 and 5 after days induction and 45, 75 and 120 days after the installation of diabetes mellitus.The lipid peroxidation index, measured by TBARS concentration, showed a significant increase (p<0.05) in diabetic animals in comparison to animals control. However, the antioxidant parameter, measured by GSH content, was significantly decrease (p<0.05) in diabetic animals. Histomorphometric analysis showed a significant increase (p<0.05) in femoral trabecular separation together with a significant decrease (p<0.05) in trabecular thickness and reduced trabecular bone volume in diabetic rats. Moreover, biomechanical testing and BMD values were significant decrease (p<0.05) in diabetic group. Thus, our results demonstrated that increased lipid peroxidation and altered antioxidant defense could be related to the development of oxidative stress and diabetic osteopenia in premenopausal rats

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The study aims to answer the following question: what are the different profiles of infant mortality, according to demographic, socioeconomic, infrastructure and health care, for the micro-regions at the Northeast of Brazil? Thus, the main objective is to analyze the profiles or typologies associated mortality levels sociodemographic conditions of the micro-regions, in the year 2010. To this end, the databases of birth and death certificates of SIM and SINASC (DATASUS/MS), were taken from the 2010 population Census microdata and from SIDRA/IBGE. As a methodology, a weighted multiple linear regression model was used in the analysis in order to find the most significant variables in the explanation child mortality for the year 2010. Also a cluster analysis was performed, seeking evidence, initially, of homogeneous groups of micro-regions, from of the significant variables. The logit of the infant mortality rate was used as dependent variable, while variables such as demographic, socioeconomic, infrastructure and health care in the micro-regions were taken as the independent variables of the model. The Bayesian estimation technique was applied to the database of births and deaths, due to the inconvenient fact of underreporting and random fluctuations of small quantities in small areas. The techniques of Spatial Statistics were used to determine the spatial behavior of the distribution of rates from thematic maps. In conclusion, we used the method GoM (Grade of Membership), to find typologies of mortality, associated with the selected variables by micro-regions, in order to respond the main question of the study. The results points out to the formation of three profiles: Profile 1, high infant mortality and unfavorable social conditions; Profile 2, low infant mortality, with a median social conditions of life; and Profile 3, median and high infant mortality social conditions. With this classification, it was found that, out of 188 micro-regions, 20 (10%) fits the extreme profile 1, 59 (31.4%) was characterized in the extreme profile 2, 34 (18.1%) was characterized in the extreme profile 3 and only 9 (4.8%) was classified as amorphous profile. The other micro-regions framed up in the profiles mixed. Such profiles suggest the need for different interventions in terms of public policies aimed to reducing child mortality in the region

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This work was developed in the research line: "The habitus of study: builder of a new reality in the basic education of metropolitan area Natal" which is being developed with the support of CAPES by the Centre for Education. Acts, especially the problem of academic performance of students in basic education of the public in the Metropolitan Region of Natal (RMN). Thus, the aim of this paper is to construct a typology of students in the 9th year of basic education, attending the public schools (state or municipal) of MRN, 2009, and assess, according to these profiles, what personal characteristics student and their families: economic, social and cultural capital as well as teaching practices create environments capable of favoring a good educational development as measured by the performance obtained in the assessments in mathematics and English language. The data used were provided through the microdata Brazil Exam 2009 held by INEP. We used the methods Grade of Membership (GoM) for construction of profiles relevance of students according to the characteristics already mentioned. With these profiles was verified, which were effectively generating good performance in school curriculum components evaluated. The findings indicate that students belonging to the profile considered good environment, able to achieve better school performance both in Portuguese as in Mathematics, compared to the extreme profiles and adverse deficit

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This work aims to study the problem of the formal job in the Brazilian Northeast region and its effect in the social inclusion, taking for base the analysis of variables defined in the Atlas of Social Exclusion, which is based on the 2000 Brazilian Census, choosing the county as unit of analysis. As methodological options, an exploratory data analysis was performed, followed by multivariate statistical techniques, such as weighted multiple regression analysis, cluster analysis and exploratory analysis of spatial data. The results pointed out to low rates of formal job for the active age population as well as low indexes of social inclusion in the Northeast region of Brazil. A strong association of the formal job with the indicators of social inclusion under investigation, was evidenced (schooling, inequality, poverty, youth and income form government transfers), as well as a strong association of the formal job with the new index of social inclusion (IIS), modified from the IES. At the Federative Units, in which better levels of formal job had been found, good indexes of social inclusion are also observed. Highlights for the state of the Rio Grande do Norte, with the best conditions of life, and for the states of the Maranhão and Piauí, with the worst conditions. The situation of the Northeast region, facing the indicators under study, is very precarious, claiming for the necessity of emphasizing programs and governmental actions, specially directed to the raise of formal job levels of the region, reflecting, thus, in improvements on the income inequality, as well as in the social inclusion of the population of Northeastern natives.