Uma nova proposta de antenas Quasi-Yagi banda larga para comunicação sem fio

ln this work, planar quasi- Y agi antennas are investigated based on the concept of the classic Y agi_Uda antennas. These antennas represent improvements on the topologies of the antennas existing printed because they present characteristics of broad bandwidth, excellent radiation diagrams and simple construction. New configurations are adapted for the driver of the antennas, introducing patches elements into the driver. These new configurations are named Patches Elements Anteonas (PEA). This adaptation is obtained from simulations that are executed usiog the software C8T Microwave 8tudio 5. After doing the optimizations, procedures for construction and measurement ofthe prototypes are executed in order to improve the performance of the antennas in such way that they could be used in wireless communication applications, such as Bluetooth, WLAN' s and Wi-Fi. Next, the quasi- Y agi antennas are studied in order to implement them in arrangements. The arrangements construction is based 00 the best driver configuration of the antenna developed in this work. First, a linear arrangement composed by two elements of quasi¬Yagi antennas is constructed in such way that the radiation characteristics and the mutual coupling effects could be analyzed. After that, a 90° angle arrangement composed by two elements is studied to observe the effect of circular polarization. Experiments are executed in order to evaluate the arrangements performance. The experimental results show that the analysis made in this work is efficient and accurate. The numerical values obtained for the analyzed parameters of each structure developed are compared with the experimental values. 80, it is possible to observe a good concordance between them. Finally, some future works proposals are presented

Design of an X-band tray-type spatial power combiner using uniplanar quasi-Yagi antennas

The design of an X-band tray-type spatial power combiner, which employs uniplanar quasi-Yagi antennas (QYAs) for receiving and transmitting signals by individual amplifiers, is presented. Passive and active varieties of a seven-tray power-combining structure that includes two hard horns for uniform signal launching and combining across the tray stack are developed and measured. In order to compensate for nonuniform phase across the stack, which is caused by the nonplanar wave front of the horn antennas, Schiffman phase shifters are implemented in individual trays. The experimental-results show an improved performance of the investigated tray-type power combiner when the proposed phase-error compensation is implemented. (C) 2004 Wiley Periodicals, Inc.

Efeito do ganho da antena nas perdas de percurso de uma ligação

O presente trabalho tem como objectivo principal a realização de um estudo do efeito do ganho das antenas nas perdas de percurso de uma ligação na banda de frequência ISM (Insdustrial Scientific and Medical) nos 2,4 GHz. Para tal, foram utilizadas 14 antenas de 7 tipos diferentes (2 monopolo, 2 colineares, 2 grelhas, 2 Yagi, 2 painéis, 2 parabólicas e 2 helicoidais) com ganhos a variar desde os 1,3 a 23 dBi. Inicialmente, obtiveram-se os parâmetros fundamentais das antenas utilizadas, nomeadamente o diagrama de radiação e o ganho. Desenvolveu-se um sistema, que permite a medição do diagrama de radiação de forma automática através de um motor passo a passo. Uma aplicação desenvolvida em ambiente Matlab realiza o controlo do motor e desenha o respectivo diagrama em tempo real. Para a realização das medições da propagação do sinal desenvolveu-se um sistema que interliga a antena receptora a um computador portátil através de um analisador de espectros. À medida que as medições são efectuadas, a atenuação do sinal em função da distância é determinada e apresentada graficamente no computador sendo, ainda, representada a atenuação esperada no espaço livre. Para isto, implementou-se uma aplicação em ambiente Matlab que faz o tratamento e representação dos dados. Tendo-se conhecimento dos parâmetros das antenas, e com o sistema de medição implementado, passou-se às medições da propagação do sinal em diferentes meios, tais como, meio sem obstáculos, meio urbano, meio florestal caracterizado por troncos no percurso de propagação e meio florestal caracterizado por folhagem no percurso de propagação. Em cada meio foram efectuadas medições para 37 combinações de antenas, com ganhos conjuntos a variar desde os 2,6 até o 46 dBi. As medições foram efectuadas com a colocação da antena emissora numa posição fixa e com o afastamento da antena receptora em intervalos de 5 metros, até os 150 metros, seguindo a linha de máxima radiação entre ambas as antenas. Ainda, para os meios sem obstáculos e florestais, foram efectuadas medições para dois ângulos em relação à linha indicada, sendo estes de 30° e 330°, respectivamente. Com base nos resultados obtidos, verificou-se um aumento da atenuação à medida que se passou para meios mais obstruídos, sendo que, para o meio sem obstáculos a atenuação aproxima-se da curva do espaço livre. No meio urbano observou-se que a atenuação aumentou ligeiramente. No entanto, esta não é muito significativa quando comparada com a atenuação no espaço livre. Por último, notou-se um grande aumento da atenuação nos meios florestais, ao nível dos troncos e da vegetação, sendo superior para esta última. Relativamente às antenas, verificou-se que existe um aumento da atenuação na medida que o ganho destas aumenta, sendo mais visível para meios com maior obstrução (florestais). Para a situação em que as antenas encontram-se com desvios de 30° e 330°, verificou-se que este aumento é mais significativo para as antenas directivas (ganhos superiores).

Projeto de uma antena para controlo wireless de um robot

A comunicação e transmissão de informação sem fios tornou - se uma realidade cada vez mais utilizada pelas sociedades contemporâneas. A nível profissional, as forças armadas de cada país acharam conveniente modernizar os seus meios, por forma a aumentar a eficiência e a segurança em determinadas tarefas. Nesse sentido, o Exército português adquiriu um robot (ROVIM) cuja função é desempenhar ações de reconhecimento e vigilância de modo a obter informações de forma segura. O objetivo desta dissertação é dimensionar e construir uma antena para controlo wireless do robot (ROVIM). As especificações técnicas desta antena requerem dois modos de operação, um com uma largura de feixe larga e outro com uma largura de feixe estreita. Para alcançar esses objetivos dimensionou-se e construiu-se duas antenas. Na dissertação são construídas duas antenas, a primeira é uma antena Yagi – Uda convencional e a segunda é uma antena com uma estrutura nova que permite a regulação do ganho e da largura de feixe a -3 dB. A primeira antena será o modelo base da segunda antena, que apresenta a inovação do controlo das caraterísticas de radiação. Esse controlo é possível através da introdução de díodos e do respetivo circuito de polarização na estrutura da antena. Inicialmente, as antenas foram dimensionadas e simuladas recorrendo ao programa de simulação CST MWS, de modo a operarem na banda dos 2,4 GHz. Após a construção das antenas, as caraterísticas de radiação foram medidas recorrendo à câmara anecoica e ao network analyzer, permitindo assim a comparação dos resultados medidos com os simulados.

A quasi stationary approach to drying kinetics of cylindrical food particulates in a heat pump asisted fluid bed dryer

Experiments were undertaken to study drying kinetics of moist cylindrical shaped food particulates during fluidised bed drying. Cylindrical particles were prepared from Green beans with three different length:diameter ratios, 3:1, 2:1 and 1:1. A batch fluidised bed dryer connected to a heat pump system was used for the experimentation. A Heat pump and fluid bed combination was used to increase overall energy efficiency and achieve higher drying rates. Drying kinetics, were evaluated with non-dimensional moisture at three different drying temperatures of 30, 40 and 50o C. Numerous mathematical models can be used to calculate drying kinetics ranging from analytical models with simplified assumptions to empirical models built by regression using experimental data. Empirical models are commonly used for various food materials due to their simpler approach. However problems in accuracy, limits the applications of empirical models. Some limitations of empirical models could be reduced by using semi-empirical models based on heat and mass transfer of the drying operation. One such method is the quasi-stationary approach. In this study, a modified quasi-stationary approach was used to model drying kinetics of the cylindrical food particles at three drying temperatures.

Prediction of fluidization behaviour and a quasi-stationary approach to drying kinetics of irregular particulate food materials

Changes in fluidization behaviour behaviour was characterised for parallelepiped particles with three aspect ratios, 1:1, 2:1 and 3:1 and spherical particles. All drying experiments were conducted at 500C and 15 % RH using a heat pump dehumidifier system. Fluidization experiments were undertaken for the bed heights of 100, 80, 60 and 40 mm and at 10 moisture content levels. Due to irregularities in shape minimum fluidisation velocity of parallelepiped particulates (potato) could not fitted to any empirical model. Also a generalized equation was used to predict minimum fluidization velocity. The modified quasi-stationary method (MQSM) has been proposed to describe drying kinetics of parallelepiped particulates at 30o C, 40o C and 50o C that dry mostly in the falling rate period in a batch type fluid bed dryer.

A quasi-stationary approach to drying kinetics of different shaped food particulates in a heat pump assisted by fluid bed dryer

Experiments were undertaken to study drying kinetics of different shaped moist food particulates during heat pump assisted fluidised bed drying. Three particular geometrical shapes of parallelepiped, cylindrical and spheres were selected from potatoes (aspect ratio = 1:1, 2:1, 3:1), cut beans (length: diameter = 1:1, 2:1, 3:1) and peas respectively. A batch fluidised bed dryer connected to a heat pump system was used for the experimentation. A Heat pump and fluid bed combination was used to increase overall energy efficiency and achieve higher drying rates. Drying kinetics, were evaluated with non-dimensional moisture at three different drying temperatures of 30, 40 and 50o C. Due to complex hydrodynamics of the fluidised beds, drying kinetics are dryer or material specific. Numerous mathematical models can be used to calculate drying kinetics ranging from analytical models with simplified assumptions to empirical models built by regression using experimental data. Empirical models are commonly used for various food materials due to their simpler approach. However problems in accuracy, limits the applications of empirical models. Some limitations of empirical models could be reduced by using semi-empirical models based on heat and mass transfer of the drying operation. One such method is the quasi-stationary approach. In this study, a modified quasi-stationary approach was used to model drying kinetics of the cylindrical food particles at three drying temperatures.

A quasi four dimensional radiation detector

Techniques for the accurate measurement of ionising radiation have been evolving since Roentgen first discovered x-rays in 1895; until now experimental measurements of radiation fields in the three spatial dimensions plus time have not been successfully demonstrated. In this work, we embed an organic plastic scintillator in a polymer gel dosimeter to obtain the first quasi-4D experimental measurement of a radiation field.

Stochastic chemical kinetics and the quasi-steady-state assumption : application to the stochastic simulation algorithm and chemical master equation

Recently the application of the quasi-steady-state approximation (QSSA) to the stochastic simulation algorithm (SSA) was suggested for the purpose of speeding up stochastic simulations of chemical systems that involve both relatively fast and slow chemical reactions [Rao and Arkin, J. Chem. Phys. 118, 4999 (2003)] and further work has led to the nested and slow-scale SSA. Improved numerical efficiency is obtained by respecting the vastly different time scales characterizing the system and then by advancing only the slow reactions exactly, based on a suitable approximation to the fast reactions. We considerably extend these works by applying the QSSA to numerical methods for the direct solution of the chemical master equation (CME) and, in particular, to the finite state projection algorithm [Munsky and Khammash, J. Chem. Phys. 124, 044104 (2006)], in conjunction with Krylov methods. In addition, we point out some important connections to the literature on the (deterministic) total QSSA (tQSSA) and place the stochastic analogue of the QSSA within the more general framework of aggregation of Markov processes. We demonstrate the new methods on four examples: Michaelis–Menten enzyme kinetics, double phosphorylation, the Goldbeter–Koshland switch, and the mitogen activated protein kinase cascade. Overall, we report dramatic improvements by applying the tQSSA to the CME solver.