Orientação e magnitude de tensões na bacia potiguar: implicações para evolução de bacias em margens passivas

This study presents new stress orientations and magnitudes from the Potiguar basin in the continental margin of Brazil. We analyzed breakout and drilled induced fractures derived from resistivity image logs run in ten oil wells. We also used direct Shmin measurements determined from hydraulic fractures and rock strength laboratory analysis. In addition, we compared these results with 19 earthquake focal mechanisms located in the crystalline basement. We observed that stress directions and magnitudes change across the basin and its basement. In the basin, the SHmax gradient of 20.0 MPa/km and the SHmax/Shmin ratio of 1.154 indicate a normal stress regime from 0.5 to 2.0 km, whereas the SHmax gradient of 24.5MPa/km and the SHmax/Shmin ratio of 1.396 indicate a strike slip stress regime from 2.5 to 4.0 km. The deeper strike-slip stress regime in the basin is similar to the regime in the basement at 1-12 km deep. This stress regime transition is consistent with an incipient tectonic inversion process in the basin. We also noted that the SHmax direction rotates from NW SE in the western part of the Potiguar basin to E W in its central and eastern part, following roughly the shoreline geometry. It indicates that local factors, as density contrast between continental and oceanic crust and sediment loading at the continental shelf influence the stress field. The concentration of fluid pressure in faults of the lowpermeability crystalline basement and its implications to establish a critically stressed fault regime in the basement is also discussed

Fratura precoce da porcelana em restaurações com infra-estrutura de zircônia: influência de gradientes térmicos no desenvolvimento e magnitude de tensões residuais e transitórias

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Criação de zonas de alta permeabilidade em fraturas: modelagem numérica do Lajedo de Soledade, Formação Jandaíra, Bacia Potiguar

The fracturing in carbonate rocks has been attracting increasingly attention due to new oil discoveries in carbonate reservoirs. This study investigates how the fractures (faults and joints) behave when subjected to different stress fields and how their behavior may be associated with the generation of karst and consequently to increased secondary porosity in these rocks. In this study I used satellite imagery and unmanned aerial vehicle UAV images and field data to identify and map faults and joints in a carbonate outcrop, which I consider a good analogue of carbonate reservoir. The outcrop comprises rocks of the Jandaíra Formation, Potiguar Basin. Field data were modeled using the TECTOS software, which uses finite element analysis for 2D fracture modeling. I identified three sets of fractures were identified: NS, EW and NW-SE. They correspond to faults that reactivate joint sets. The Ratio of Failure by Stress (RFS) represents stress concentration and how close the rock is to failure and reach the Mohr-Coulomb envelopment. The results indicate that the tectonic stresses are concentrated in preferred structural zones, which are ideal places for carbonate dissolution. Dissolution was observed along sedimentary bedding and fractures throughout the outcrop. However, I observed that the highest values of RFS occur in fracture intersections and terminations. These are site of karst concentration. I finally suggest that there is a relationship between stress concentration and location of karst dissolution in carbonate rocks.

Criação de zonas de alta permeabilidade em fraturas: modelagem numérica do Lajedo de Soledade, Formação Jandaíra, Bacia Potiguar

The fracturing in carbonate rocks has been attracting increasingly attention due to new oil discoveries in carbonate reservoirs. This study investigates how the fractures (faults and joints) behave when subjected to different stress fields and how their behavior may be associated with the generation of karst and consequently to increased secondary porosity in these rocks. In this study I used satellite imagery and unmanned aerial vehicle UAV images and field data to identify and map faults and joints in a carbonate outcrop, which I consider a good analogue of carbonate reservoir. The outcrop comprises rocks of the Jandaíra Formation, Potiguar Basin. Field data were modeled using the TECTOS software, which uses finite element analysis for 2D fracture modeling. I identified three sets of fractures were identified: NS, EW and NW-SE. They correspond to faults that reactivate joint sets. The Ratio of Failure by Stress (RFS) represents stress concentration and how close the rock is to failure and reach the Mohr-Coulomb envelopment. The results indicate that the tectonic stresses are concentrated in preferred structural zones, which are ideal places for carbonate dissolution. Dissolution was observed along sedimentary bedding and fractures throughout the outcrop. However, I observed that the highest values of RFS occur in fracture intersections and terminations. These are site of karst concentration. I finally suggest that there is a relationship between stress concentration and location of karst dissolution in carbonate rocks.

Influência das tensões tectônicas na permeabilidade da formação Açu - Bacia Potiguar

The behavior of the fluid flux in oil fields is influenced by different factors and it has a big impact on the recovery of hydrocarbons. There is a need of evaluating and adapting the actual technology to the worldwide reservoirs reality, not only on the exploration (reservoir discovers) but also on the development of those that were already discovered, however not yet produced. The in situ combustion (ISC) is a suitable technique for these recovery of hydrocarbons, although it remains complex to be implemented. The main objective of this research was to study the application of the ISC as an advanced oil recovery technique through a parametric analysis of the process using vertical wells within a semi synthetic reservoir that had the characteristics from the brazilian northwest, in order to determine which of those parameters could influence the process, verifying the technical and economical viability of the method on the oil industry. For that analysis, a commercial reservoir simulation program for thermal processes was used, called steam thermal and advanced processes reservoir simulator (STARS) from the computer modeling group (CMG). This study aims, through the numerical analysis, find results that help improve mainly the interpretation and comprehension of the main problems related to the ISC method, which are not yet dominated. From the results obtained, it was proved that the mediation promoted by the thermal process ISC over the oil recovery is very important, with rates and cumulated production positively influenced by the method application. It was seen that the application of the method improves the oil mobility as a function of the heating when the combustion front forms inside the reservoir. Among all the analyzed parameters, the activation energy presented the bigger influence, it means, the lower the activation energy the bigger the fraction of recovered oil, as a function of the chemical reactions speed rise. It was also verified that the higher the enthalpy of the reaction, the bigger the fraction of recovered oil, due to a bigger amount of released energy inside the system, helping the ISC. The reservoir parameters: porosity and permeability showed to have lower influence on the ISC. Among the operational parameters that were analyzed, the injection rate was the one that showed a stronger influence on the ISC method, because, the higher the value of the injection rate, the higher was the result obtained, mainly due to maintaining the combustion front. In connection with the oxygen concentration, an increase of the percentage of this parameter translates into a higher fraction of recovered oil, because the quantity of fuel, helping the advance and the maintenance of the combustion front for a longer period of time. About the economic analysis, the ISC method showed to be economically feasible when evaluated through the net present value (NPV), considering the injection rates: the higher the injection rate, the higher the financial incomes of the final project

Influência das tensões tectônicas na permeabilidade da formação Açu - Bacia Potiguar

The behavior of the fluid flux in oil fields is influenced by different factors and it has a big impact on the recovery of hydrocarbons. There is a need of evaluating and adapting the actual technology to the worldwide reservoirs reality, not only on the exploration (reservoir discovers) but also on the development of those that were already discovered, however not yet produced. The in situ combustion (ISC) is a suitable technique for these recovery of hydrocarbons, although it remains complex to be implemented. The main objective of this research was to study the application of the ISC as an advanced oil recovery technique through a parametric analysis of the process using vertical wells within a semi synthetic reservoir that had the characteristics from the brazilian northwest, in order to determine which of those parameters could influence the process, verifying the technical and economical viability of the method on the oil industry. For that analysis, a commercial reservoir simulation program for thermal processes was used, called steam thermal and advanced processes reservoir simulator (STARS) from the computer modeling group (CMG). This study aims, through the numerical analysis, find results that help improve mainly the interpretation and comprehension of the main problems related to the ISC method, which are not yet dominated. From the results obtained, it was proved that the mediation promoted by the thermal process ISC over the oil recovery is very important, with rates and cumulated production positively influenced by the method application. It was seen that the application of the method improves the oil mobility as a function of the heating when the combustion front forms inside the reservoir. Among all the analyzed parameters, the activation energy presented the bigger influence, it means, the lower the activation energy the bigger the fraction of recovered oil, as a function of the chemical reactions speed rise. It was also verified that the higher the enthalpy of the reaction, the bigger the fraction of recovered oil, due to a bigger amount of released energy inside the system, helping the ISC. The reservoir parameters: porosity and permeability showed to have lower influence on the ISC. Among the operational parameters that were analyzed, the injection rate was the one that showed a stronger influence on the ISC method, because, the higher the value of the injection rate, the higher was the result obtained, mainly due to maintaining the combustion front. In connection with the oxygen concentration, an increase of the percentage of this parameter translates into a higher fraction of recovered oil, because the quantity of fuel, helping the advance and the maintenance of the combustion front for a longer period of time. About the economic analysis, the ISC method showed to be economically feasible when evaluated through the net present value (NPV), considering the injection rates: the higher the injection rate, the higher the financial incomes of the final project

Sismicidade e correlação com feições geológicas: o caso do lineamento Pernambuco e seu entorno

This thesis presents and discusses the results of the various seismic areas in the State of Pernambuco, with the aim of having a vision of regional seismicity and its causes. To the papers published in journals were added two new original works submitted to international journals, dealing with seismic areas located in the counties of São Caetano, Cupira, and Agrestina. All seismic areas mentioned in this thesis are located on the Pernambuco Lineament and its surroundings (both in branches or single faults within 40 km of it). The Pernambuco Lineament is a Neoproterozoic shear zone of continental-scale that deformed the Borborema Province, and presents as branches, shear zones with NE-SW direction. The new submitted papers are from the analysis of data collected by three local networks of stations that operated in the following areas: network SO07 (seismicity in the district of Santa Luzia - São Caetano, 2007), network BM10 (data from seismic areas of Serra Verde ( Cupira) and Barra do Chata (Agrestina), in 2010), network SO10 (seismicity near the urban center of São Caetano in 2010). These data were used for determining the hypocenters and focal mechanisms in order to discuss the relationship between the seismicity and geological features of the area. The new mechanisms obtained, as well as the previously published allowed the determination of the direction of the average stress in the region. The direction of stress in the region involving the various seismic areas, now or previously studied, is quite stable and approximate EW direction (SHmax). The correlation between seismicity and geological features is observed on the lineament and north of it. In the south (Cupira and Agrestina), in seismic areas nearby shear zones NE-SW, there is no correlation and seismogenic EW normal faults are active and its motion is compatible with regional stresses. It is probable that these active faults are more recent than the Neoproterozoic, probably of the Cretaceous period, when the last great movement of the Pernambuco Lineament occurred

Estudo da atividade sísmica em São Caetano-PE em 2007

In this dissertation we studied the seismic activity in the São Caetano county, Pernambuco State, Northeastern Brazil, located near the Pernambuco Lineament. The Pernambuco Lineament is a one of Neoproterozoic continental-scale shear zones that deforms the Borborema province. The seismicity estudied occurred in a NE trending branch of Pernambuco Lineament. The seismic activity in São Caetano started in 2006 and in May 20th, 2006 a 4,0 mb earthquake hit there. This was the largest earthquake ever reported in Pernambuco State. This dissertation is the result of a campaign done in the period from Februay 1th 2007 to July 31 th 2007. In this campaign up to nine three-component digital seismographic stations were deployed and the collected data was used to determine hypocenters and focal mechanism. A total of 214 earthquakes, recorded at least by three stations, were analyzed. To determine hypocenters and time origin the HYPO71 program was used assuming a half-space model with parameters : VP (P-wave velocity) equal to 5.90 km/s and the ratio VP/VS 1.70, where VS is the S-wave velocity. The earthquakes hypocentral distribution was approximately 4 km long and agrees with the NE-SW direction of the Pernambuco Lineamento branch. Hypocentres depth range from 2 to 8 km. The composed focal mechanism was made from a group of 14 selected earthquakes. We try firstly to find the fault plane solution matching the polarity distribution at stations, using the FPFIT program. The result was 43 deg ± 15 deg for strike, 59 deg ± 9 deg for dip and -142 deg ± 15 deg for rake. We also fitted a plane using the hypocentral distribution to obtain the dip and azimuth of the hypocentral distribution. The results obtained by this fit were 58 deg for the azimuth, 55 deg for the dip and -155 deg for rake. This result shows a mechanism of a strike-slip dextral fault with a normal component. This dissertation shows, once more, that there is a good correlation between the seismic activity and geological features in the region near the Pernambuco Lineament and its NE branches

Parâmetros de fonte de microterremotos em Cascavel-CE

In this dissertation it was studied the rupture characteristic of earthquakes of the Town of Cascavel CE, Northeastern Brazil. Located on the border of the Potiguar Basin, the Town of Cascavel is one of the most seismically active intraplate areas in the country. In this town, on November 20th, 1980 a 5,2mb earthquake occurred. This was the largest earthquake ever reported in Northeast Brazil. Studies of this region using instruments were possible after 1989, with several campaigns being done using seismographic networks. From the beginning of the monitoring to April 2008 more than 55,000 events were recorded. With the data collected by a network with six 3-components digital seismographic stations during the campaigns done from September 29th, 1997 to March 5th, 1998, estimates of source parameters were found fitting the displacement spectra in the frequency domain for each event. From the fitting of the displacement spectra it was possible to obtain the corner frequency ( ) c f and long period amplitude ( ) W0 . Source parameters were determined following Brune (1970) and Madariaga (1976) models. Twenty-one seismic events were analyzed (0.7 £ £ 2.1) b m in order to estimate the source dimension (r ), seismic moment ( ) M0 , static stress drop (Ds ), apparent stress ( ) a s , seismic energy ( ) S E and moment magnitude ( ) W M for each of the events. It was observed that the ratio between radiated seismic energy and moment seismic (apparent stress) increases with increasing moment and hence magnitude at the observed range. As suggested by Abercrombie (1995), also in this work there is a breakdown in the scaling for earthquakes with magnitudes smaller than three ( < 3.0) W M , so that the rupture physics is different for larger events. If this assumption is valid, the earthquakes analyzed in this work are not selfsimilar. Thus, larger events tend to radiated more energy per unit area than smaller ones.

Correlação entre contexto morfoestrutural e sismicidade nas regiões de João Câmara e São Rafael (RN)

This MSc thesis describes brittle deformation in two seismic zones located in north-eastern Brazil: João Câmara and São Rafael, Rio Grande do Norte State. Both areas show seismogenic faults, Samambaia and São Rafael, indicated by narrow zones of epicentres with a strike of 040o, a lenght of 30 km and 4 km, and a depth of 1-12 and 0,5-4 km, respectively. The first seismological and geological studies suggested blind faults or faults that were still in the beginning of the nucleation process. The region is under E-W-oriented compression and is underlain by Precambrian terrains, deformed by one or more orogenic cycles, which generated shear zones generally marked by strong pervasive foliation and sigmoidal shapes. The crystalline basement is capped by the Cretaceous Potiguar basin, which is also locally capped by Pliocene continental siliciclastic deposits (Barreiras Formation), and Quaternary alluvium. The main aim of this study was to map epicentral areas and find whether there are any surface geological or morphotectonic expression related to the seismogenic faults. A detailed geological map was carried out in both seismic areas in order to identify brittle structures and fault-related drainage/topographic features. Geological and morphotectonic evidence indicate that both seismogenic faults take place along dormant structures. They either cut Cenozoic rocks or show topographic expression, i.e., are related to topographic heights or depressions and straight river channels. Faults rocks in the Samambaia and São Rafael faults are cataclasite, fault breccia, fault gouge, pseudotachylyte, and quartz veins, which point to reactivation processes in different crustal levels. The age of the first Samambaia and the São Rafael faulting movement possibly ranges from late Precambrian to late Cretaceous. Both fault cut across Precambrian fabric. They also show evidence of brittle processes which took place between 4 and 12 km deep, which probably have not occurred in Cenozoic times. The findings are of great importance for regional seismic hazard. They indicate that fault zones are longer than previously suggested by seismogenic studies. According to the results, the methodology used during this thesis may also be useful in other neotectonic investigation in intraplate areas

Parafusos bioabsorvíveis na reparação de fraturas experimentais de sesamóides proximais em eqüinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação de parafusos bioabsorvíveis na reparação de fraturas experimentais de sesamóides em eqüinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito da espessura oclusal do cimento e da sua união à cerâmica na resistência à fratura de coroas CAD/CAM: método de elementos finitos e testes monotônicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sismicidade e esforços tectônicos na zona sísmica Acaraú, Nordeste do Brasil

Inside the Borborema Province the Northwestern Ceará (NC) is one of the most seismic active regions. There are reports of an earthquake occurred in 1810 in the Granja town. On January, 2008 the seismic activity in NC has increased and it was deployed a seismographic network with 11 digital stations. In 2009, another earthquake sequence began and it was deployed another seismographic network in the Santana do Acaraú town with 6 stations. This thesis presents the results obtained by analyzing the data recorded in these two networks. The epicentral areas are located near the northeastern part of the Transbrasiliano Lineament, a shear zone with NE-SW-trending that cuts the study area. The hypocenters are located between 1km and 8km. The strike-slip focal mechanisms were found, which is predominant in the Borborema Province. An integration of seismological, geological and geophysical data was performed and it show that the seismogenic faults found are oriented in the same direction to the local brittle structures observed in field and magnetic lineaments. The SHmax (maximum compressional stress) direction in NC was estimated using an inversion of seven focal mechanisms. The horizontal maximum compression stress (σ1 = 300°) with orientation NW-SE and extension (σ3 = 210°) with NE-SW and σ2 vertical. These results are consistent with results of previous studies. The seismic activity recorded in NC is not related to a possible reactivation of the Transbrasiliano Lineament, by now.

Plastificação de um solo cimentado curado sob tensão

A fim de avaliar a contribuição das ligações cimentantes no comportamento tensão-deformação dos solos cimentados, bem como quantificar a variação das tensões de início de plastificação e incremento de tensão de plastificação em função do índice de vazios de cura, foram realizados dezoito ensaios de compressão isotrópica em amostras artificialmente cimentadas curadas com diferentes tensões confinantes, índices de vazios e teores de cimento. As amostras foram inicialmente adensadas a várias tensões confinantes ao longo da linha de compressão normal do solo sem cimentação, simulando a formação de elementos de solos em diferentes profundidades de um depósito sedimentar cimentado. Após o adensamento, as amostras eram curadas para posterior aplicação de incrementos de tensão isotrópica. Complementarmente, dezenove ensaios triaxiais drenados foram realizados em amostras artificialmente cimentadas curadas sob diferentes tensões confinantes e índices de vazios de forma a analisar as modificações dos parâmetros de resistência, deformabilidade e plastificação em função do índice de vazios e tensão de cura. Por final, um novo modelo matemático foi proposto para simular os ensaios isotrópicos das amostras curadas com diferentes índices de vazios e teores de cura, descrevendo o comportamento teórico dos elementos de solo situados nas diferentes profundidades do depósito fictício de solo cimentado. A capacidade do modelo de simular os resultados dos ensaios isotrópicos para uma gama ampla de índice de vazios de cura e teores de cimento também foi apresentada. Comentários acerca das respostas obtidas com simulações de amostras curadas a altos e baixos índices de vazios, e solicitadas a elevadas tensões isotrópicas, também são apresentadas juntamente com uma análise dos três parâmetros adicionais requeridos pelo modelo em relação ao modelo Cam Clay: um parâmetro de medida de nível de cimentação, um parâmetro definidor do tipo de comportamento da estrutura cimentante (rígido, rígido-plástico, linear, etc.), e um parâmetro que relaciona a magnitude das tensões da estrutura cimentante com o nível de cimentação da amostra.