An agent-based control mechanism for WFQ in IP networks

This paper presents a new packet scheduling scheme called agent-based WFQ to control and maintain QoS parameters in virtual private networks (VPNs) within the confines of adaptive networks. Future networks are expected to be open heterogeneous environments consisting of more than one network operator. In this adaptive environment, agents act on behalf of users or third-party operators to obtain the best service for their clients and maintain those services through the modification of the scheduling scheme in routers and switches spanning the VPN. In agent-based WFQ, an agent on the router monitors the accumulated queuing delay for each service. In order to control and to keep the end-to-end delay within the bounds, the weights for services are adjusted dynamically by agents on the routers spanning the VPN. If there is an increase or decrease in queuing delay of a service, an agent on a downstream router informs the upstream routers to adjust the weights of their queues. This keeps the end-to-end delay of services within the specified bounds and offers better QoS compared to VPNs using static WFQ. This paper also describes the algorithm for agent-based WFQ, and presents simulation results. (C) 2003 Elsevier Science Ltd. All rights reserved.

Neural modelling, control and optimisation of an industrial grinding process

This paper describes the development of neural model-based control strategies for the optimisation of an industrial aluminium substrate disk grinding process. The grindstone removal rate varies considerably over a stone life and is a highly nonlinear function of process variables. Using historical grindstone performance data, a NARX-based neural network model is developed. This model is then used to implement a direct inverse controller and an internal model controller based on the process settings and previous removal rates. Preliminary plant investigations show that thickness defects can be reduced by 50% or more, compared to other schemes employed. (c) 2004 Elsevier Ltd. All rights reserved.

Comparison of a centralised and distributed approach for a generic scheduling system

PEGS (Production and Environmental Generic Scheduler) is a generic production scheduler that produces good schedules over a wide range of problems. It is centralised, using search strategies with the Shifting Bottleneck algorithm. We have also developed an alternative distributed approach using software agents. In some cases this reduces run times by a factor of 10 or more. In most cases, the agent-based program also produces good solutions for published benchmark data, and the short run times make our program useful for a large range of problems. Test results show that the agents can produce schedules comparable to the best found so far for some benchmark datasets and actually better schedules than PEGS on our own random datasets. The flexibility that agents can provide for today's dynamic scheduling is also appealing. We suggest that in this sort of generic or commercial system, the agent-based approach is a good alternative.

An empirical study of green supply chain management practices amongst UK manufacturers

Purpose: The purpose of this paper is to examine the extent and nature of greening the supply chain (SC) in the UK manufacturing sector; and the factors that influence the breadth and depth of this activity.

Design/methodology/approach: Based on the findings from a sample of manufacturing organisations drawn from the membership of The Chartered Institute for Purchasing and Supply. Data are collected using a questionnaire, piloted and pre-tested before distribution with responses from 60 manufacturing companies.

Findings: On average manufacturers perceive the greatest pressure to improve environmental performance through legislation and internal drivers (IDs). The least influential pressures are related to societal drivers and SC pressures from individual customers. Green supply chain management (GSCM) practices amongst this “average” group of UK manufacturing organisations are focusing on internal, higher risk, descriptive activities, rather than proactive, external engagement processes. Environmental attitude (EA) is a key predictor of GSCM activity and those organisations that have a progressive attitude are also operationally very active. EA shows some relationship to legislative drivers but other factors are also influential. Operational activity may also be moderated by organisational contingencies such as risk, size, and nationality.

Research limitations/implications: The main limitation to this paper is the relatively small manufacturing sample.

Practical implications: This paper presents a series of constructs that identify GSCM operational activities companies to benchmark themselves against. It suggests which factors are driving these operational changes and how industry contingencies may be influential.

Originality/value: This paper explores what is driving environmental behaviour amongst an “average” sample of manufacturers, what specific management practices take place and the relationships between them.

Keywords: Manufacturing industries, Environmental management, Supply chain management, Sustainable development, United Kingdom
Paper type: Research paper

Kinetics of Aqueous Phase Dehydration of Xylose into Furfural Catalyzed by ZSM-5 Zeolite

ZSM-5 zeolite in H+ form with an average pore size of 1.2 nm was used for aqueous phase dehydration of xylose to furfural at low temperatures;, that is, from 413 to 493 K. The selectivity in furfural increased with the temperature to a value of 473 K. Beyond this temperature, condensation reactions were significant and facilitated by the intrinsic structure of ZSM-5. A reaction mechanism that included isomerization of xylose to lyxose, dehydration of lyxose and xylose to furfural, fragmentation of furfural to organic acids, oligomerization of furfural to bi- and tridimensional furilic species, and complete dehydration of organic acids to carbonaceous deposits was developed, and the associated kinetic parameters were estimated. The rate of furfural production was found to be more sensitive to temperature than the rates of side reactions, with an estimated activation energy of 32.1 kcal/mol. This value correlated well with data in the literature obtained by homogeneous catalytic dehydration.

Characterisation of fluidised bed granulation processes using in situ Raman spectroscopy

Previous work by the authors Walker et al. [2007b. Fluidised bed characterisation using Raman spectroscopy: applications to pharmaceutical processing. Chemical Engineering Science 62, 3832–3838] illustrated that Raman spectroscopy could be used to provide 3-D maps of the concentration and chemical structure of particles in motion in a fluidised bed, within a relatively short (120 s) time window. Moreover, we reported that the technique, as outlined, has the potential to give detailed in-situ information on how the structure and composition of granules/powders within the fluidised bed (dryer or granulator) vary with the position and evolve with time. In this study we extended the original work by shortening the time window of the Raman spectroscopic analysis to 10 s, which has allowed the in-situ real-time characterisation of a fluidised bed granulation process. Here we show an important new use of the technique which allows in-situ measurement of the composition of the material within the fluidised bed in three spatial dimensions and as a function of time. This is achieved by recording Raman spectra using a probe positioned within the fluidised bed on a long-travel x–y–z stage. In these experiments the absolute Raman intensity is used to provide a direct measure of the amount of any given material in the probed volume, i.e. a particle density. Particle density profiles have been calculated over the granulation time and show how the volume of the fluidised bed decreases with an increase mean granule size. The Raman spectroscopy analysis indicated that nucleation/coalescence in this co-melt fluidised hot melt granulation system occurred over a relatively short time frame (t<30 s). The Raman spectroscopic technique demonstrated accurate correlation with independent granulation experiments which provided particle size distribution analysis. The similarity of the data indicates that the Raman spectra accurately represent solids ratios within the bed, and thus the techniques quantitative capabilities for future use in the pharmaceutical industry.

Liquid marble formation using hydrophobic powders

This work aims to investigate and quantitatively measure “liquid marble” phenomena using hydrophobic powders (granules). The hydrophobic powders based on a copper substrate were prepared by a silver deposition technique of particle sizes 9 µm, 20 µm and 320 µm and of contact angle with water approaching 160°. The hydrophobic powder poly-methylmethacralate (PMMA) particle size 42 µm and contact angle of 120° was also used to determine the effect of powder density on liquid marble stability. The experimental investigations indicated that for successful formation of liquid marbles a number of variables in addition to hydrophobicity need to be considered, namely: powder density; powder particle size; powder shape; liquid marble formation technique. It was found that liquid marbles were formed using all four powders to varying extents, with a low powder particle size forming more stable liquid marbles. In a series of gravimetric tests, adhered powder mass on liquid marbles was found to be directly proportional to the water droplet surface area. A more complete coverage of the water drops were found with PMMA powder than the hydrophobic granules. Moreover, a further procedure was developed to increase the mechanical strength of the liquid marble, by polymerising methylmethacrylate (MMA) on the surface of a PMMA powder – liquid marble, with the aim of maintaining water within a more robust PMMA – liquid marble shell. This technique may prove to be a novel way of encapsulating drug compounds, such as gentamicin sulphate, for PMMA bone cement.

Effects of Constraint Errors on Parallel Manipulators with Decoupled Motion

From perspective of structure synthesis, certain special geometric constraints, such as joint axes intersecting at one point or perpendicular to each other, are necessary in realizing the end-effector motion of kinematically decoupled parallel manipulators (PMs) along individual motion axes. These requirements are difficult to achieve in the actual system due to assembly errors and manufacturing tolerances. Those errors that violate the geometric constraint requirements are termed “constraint errors”. The constraint errors usually are more troublesome than other manipulator errors because the decoupled motion characteristics of the manipulator may no longer exist and the decoupled kinematic models will be rendered useless due to these constraint errors. Therefore, identification and prevention of these constraint errors in initial design and manufacturing stage are of great significance. In this article, three basic types of constraint errors are identified, and an approach to evaluate the effects of constraint errors on decoupling characteristics of PMs is proposed. This approach is illustrated by a 6-DOF PM with decoupled translation and rotation. The results show that the proposed evaluation method is effective to guide design and assembly.

Dilute acid hydrolysis of Lignocellulosic biomass

The overall aim of this work was to establish the optimum conditions for acid hydrolysis of hemicellulosic biomass in the form of potato peel. The hydrolysis reaction was undertaken in a 1l high pressure pilot batch reactor using dilute phosphoric acid. Analysis of the decomposition rate of hemicellulosic biomass (namely Cellulose, Hemicellulose and lignin) was undertaken using HPLC of the reaction products namely, 5 and 6 carbon sugars. Process parameters investigated included, reactor temperature (from 135 degrees C to 200 degrees C) and acid concentration (from 2.5% (w/w) to 10% (w/w)). Analysis of the reactor products indicated that high conversion of cellulose to glucose was apparent although arabinose conversion was quite low due to thermally un-stability. However, an overall sugar yield is 82.5% was achieved under optimum conditions. This optimum yield was obtained at 135 degrees C and 10% (w/w) acid concentration. 55.2 g sugar/100 g dry potato peel is produced after a time of 8 min. The work indicates that the use of potato peel may be a feasible option as a feed material for the production of sugars for biofuel synthesis, due its low cost and high sugar yields. (C) 2009 Elsevier B.V. All rights reserved.

An absorptive capacity interpretation of Six Sigma

Purpose – The Six Sigma approach to business improvement has emerged as a phenomenon in both the practitioner and academic literature with potential for achieving increased competitiveness and contributing. However, there is a lack of critical reviews covering both theory and practice. Therefore, the purpose of this paper is to critically review the literature of Six Sigma using a consistent theoretical perspective, namely absorptive capacity.

Design/methodology/approach – The literature from peer-reviewed journals has been critically reviewed using the absorptive capacity framework and dimensions of acquisition, assimilation, transformation, and exploitation.

Findings – There is evidence of emerging theoretical underpinning in relation to Six Sigma borrowing from an eclectic range of organisational theories. However, this theoretical development lags behind practice in the area. The development of Six Sigma in practice is expanding mainly through more rigorous studies and applications in service-based environments (profit and not for profit). The absorptive capacity framework is found to be a useful overarching framework within which to situate existing theoretical and practice studies.

Research limitations/implications – Agendas for further research from the critical review, in relation to both theory and practice, have been established in relation to each dimension of the absorptive capacity framework.

Practical implications – The paper shows that Six Sigma is both a strategic and operational issue and that focussing solely on define, measure, analyse, improve control-based projects can limit the strategic effectiveness of the approach within organisations.

Originality/value – Despite the increasing volume of Six Sigma literature and organisational applications, there is a paucity of critical reviews which cover both theory and practice and which suggest research agendas derived from such reviews.

Modelling the Geometry of the Repeat Unit Cell of Three-Dimensional Weave Architectures,

The three-dimensional (3D) weaving process offers the ability to tailor the mechanical properties via design of the weave architecture. One repeat of the 3D woven fabric is represented by the unit cell. The model accepts basic weaver and material manufacturer data as inputs in order to calculate the geometric characteristics of the 3D woven unit cell. The specific weave architecture manufactured and subsequently modelled had an angle interlock type binding configuration. The modelled result was shown to have a close approximation compared to the experimentally measured values and highlighted the importance of the representation of the binder tow path.

Thermochemistry of Ionic Liquid-Catalyzed Reactions: Theoretical and Experimental Study of the Beckmann Rearrangement-Kinetic or Thermodynamic Control?

A thermodynamic analysis of the experimental conditions of the Beckmann rearrangement reaction of oximes into amides has been undertaken to examine whether the reaction is under thermodynamic or kinetic control. To answer this question, the thermodynamic properties of the typical Beckmann rearrangement reactions in the ideal gaseous state-cyclohexanone oxime to caprolactam and 2-butanone oxime to N-methylpropanarnide-were studied by using the quantum mechanical method. Gibbs energy and equilibrium constants of the Beckmann rearrangement have been assessed in the gaseous and the liquid phases. Results of the thermodynamic analysis have shown that Beckmann rearrange ments are kinetically controlled. Thus, a search for possible active ionic liquid based catalysts for the mild reaction conditions has been performed.

Screening wall effects of a thin fluidized bed by near-infrared imaging

Near-infrared (NIR) imaging was used to observe water vapour flow in a gas-solid fluidized bed reactor. The technique consisted of a broadband light, an optical filter with a bandwidth centred on strong water vapour absorptions, a Vidicon NIR camera, a nozzle from which an optically active mixture of gas and water vapour was trans-illuminated by an NIR beam and collected data of transmittance were normalized to actual optical path. The procedure was applied to a thin fluidized bed reactor with a low aspect ratio of tube to particle diameters (D-1/d(p)) in order to validate the wall effect on flow dynamics and mass transfer during the reduction of ceria-silica by hydrogen. High concentrations of water vapour emerged in the vicinity of the wall when the bed was operated at pseudo-static conditions but disappeared when the bed was run at minimum bubbling conditions. This result shows the capability of optical methods with affordable costs to 2D imaging opaque packed bed by using a spatially resolved probe located at the exit, which is of great benefit for in situ visualization of anisotropic concentrations in packed beds under industrially relevant conditions and thus for elucidation of the underlying reaction mechanism and diffusion interactions. Crown Copyright (c) 2011 Published by Elsevier B.V. All rights reserved.

Visualization of water vapour flow in a packed bed adsorber by near-infrared diffused transmittance tomography

This work presents a procedure based on spatially-resolved near-infrared imaging, in order to observe temperature and composition maps in gas-solid packed beds subjected to effects of aspect ratio and non-isothermal conditions. The technique was applied to the water vapour flow in a packed bed adsorber of low aspect ratio, filled with silica gel, using a tuneable diode laser, focal planar array detector and tomographic reconstruction. The 2D projected images from parallel scanning permitted data to be retrieved from the packing and above the packing sections of 12.0×12.0×18.2mm at a volume-resolution of 0.15×0.15×0.026mm and a time-resolution of less than 3min. The technique revealed uneven temperature and composition maps in the core packed bed and in the vicinity of the wall due to flow maldistribution. In addition, the heat uptake from the packed bed and local cross-mixing were experimentally ascertained by local profiles of the water vapour composition and temperature under various aspect ratios and feed flow rates. The relative deviations in temperature and compositions were 11.1% and 9.3%, respectively. The deviation in composition, which covers the packing and above the packing sections, was slightly higher than the deviation of 8% obtained up-to-date but was limited to the exit of a packed bed adsorber. © 2011.