Oxygen plasma treatment of sisal fibers and polypropylene: Effects on mechanical properties of composites

Polypropylene powder and sisal fibers were oxygen plasma treated, and the mechanical properties of their composites were tested. Two main effects were investigated: the incorporation of oxygen polar groups in the polypropylene surface and the surface degradation and chain scission of both polypropylene and sisal fibers. Prior to these treatments, three reactor configurations were tested to investigate the best condition for both effects to occur in PP film. Results showed that polypropylene-cellulose adhesion forces are about an order of magnitude higher for PP film treatments at 13.56 MHz than at 40 kHz owing to much higher chain scission at lower frequencies, although it probably also occurs at high frequency and high power. Polypropylene powder treated with oxygen plasma in optimum conditions for polar group incorporation did not result in improvement in any composite mechanical property, probably owing to the polymer melting. Sisal fibers and PP powder treated In conditions of surface degradation did not improve flexural or tensile properties but resulted in higher impact resistance, comparable to the improvement obtained with the addition of compatibilizer.

Hygrothermal Aging Effect on Fatigue Behavior of GLARE

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The effect of the ocean water immersion and UV ageing on the dynamic mechanical properties of the PPS/glass fiber composites

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bioremediation of direct dyes in simulated textile effluents by a paramorphogenic form of Aspergillus oryzae

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Processing and mechanical characterization of titanium-graphite hybrid laminates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Morphological, mechanical properties and biodegradability of biocomposite thermoplastic starch and polycaprolactone reinforced with sisal fibers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electrolytic treatment of wastewater containing n-phenyl-n '-1,3-dimethylbutyl-p-phenylenediamine

This study investigated the effects of electrolytic treatment using Dimensionally Stable Anode (DSA, 70%TiO2/30%RuO2) type electrodes in simulated wastewater containing aromatic amine n-phenyl-n'-1,3-dimethylbutyl-p-phenylenediamine (Flexzone 7P). A low direct current density of 0.025 A cm(-2) was applied for periods up to 60 minutes and a 52.6% decrease in Flexzone 7P concentration was observed. Ultraviolet-visible spectra, gas chromatography, toxicity and biodegradation tests were carried out with the aim of verifying the toxic by-products that were formed. Ultraviolet-visible spectra of simulated wastewater exhibited changes in the aromatic amine's molecular structure. Additionally, based on the S. cerevisiae toxicity test, it was observed that detoxification of the wastewater occurred after 15 minutes of electrolysis. It was also observed that five minutes of treatment were sufficient to improve the biodegradation rate, determined through the respirometric Bartha method.

Calorimetric and SEM studies of PHB-PET polymeric blends

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Barrier and Mechanical Properties of Clay-Reinforced Polymeric Nanocomposites

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Extended states in disordered doped polyacetylene chains

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Cellulose degradation by Leucocoprinus gongylophorus, the fungus cultured by the leaf-cutting ant Atta sexdens rubropilosa

Leucocoprinus gongylophorus, the fungus cultured by the leaf-cutting ant Atta sexdens rubropilosa, is able to degrade efficiently cellulose, microcrystaline cellulose, carboximethylcellulose, and cellobiose. Analysis of the degradation products indicate that the fungus produce extracellular β-glucosidase, exo- and endo-glucanase. The importance of cellulose degradation to the association of fungus and ant is discussed.

Determination of density of states in PPS from space-charge-limited current measurements

Space-charge-limited currents measurements have been carried out on undoped amorphous poly p-phenylene sulfide. The scaling law is checked for different samples with varying thickness, and J-V data analyzed. The position of the quasi-Fermi level and the density of states was obtained.

Metal-insulator transitions in pressed pellets of BF4 - doped poly(3-methylthiophene)

From Electron Spin Resonance (ESR) data in pressed pellets of BF4 - doped Poly(3-methylthiophene) (P3MT) we obtained simultaneously the paramagnetic susceptibility and. the microwave conductivity. We observed a transition from a high-temperature insulator state to a room-temperature metallic state. Around 240K. evidence of a Peierls transition is observed, but if the sample is slowly cooled, this transition is partially suppressed. DC conductivity data taken with the sample quenched to 79 K show a non-linear I-V response for very small electric fields, suggesting depinning of Charge-Density Wave (CDW). The data for heating and cooling the system above room temperature, indicate the formation of bipolarons.

Electrical properties of a composite of Polyurethane and ferroelectric ceramics

Ferroelectric ceramic particles based on lead titanate zirconate (PZT) were dispersed in a polymer matrix based on castor oil. After the poling process, the pyroelectric activity of this composite was measured using a direct method in which a linear heating rate was applied to the pre-poled samples. The pyroelectric coefficient at 343 K is comparable with that of a PZT-poly(vinylidene fluoride) (PVDF) composite and significantly higher than that of PVDF. © 1998 Kluwer Academic Publishers.

Thermal analysis of conductive blends of PVDF and poly(o-methoxyaniline)

The thermal behavior of blends of poly(vinylidene fluoride), or PVDF, and poly(o-methoxyaniline) doped with toluene sulfonic acid was studied by thermogravimetic analysis, electrical conductivity measurements, differential scanning calorimetry, X-ray diffraction and scanning electron microscopy. Blends with thermal and electrical conductivity stabler than the conductive polymer alone were obtained. Nevertheless, degradation occurs after a long period of time (500 h) at high temperatures. The possible association of the conductivity decay with dopant loss, degradation and structural and morphological changes of the blend is discussed. (C) 2000 Elsevier Science Ltd.