Impact abrasion resistance quantification of protective motorcycle gloves

The hands are often the first contact point with the road surface in a motorcycle crash. Wearing well designed protective gloves has been proven to significantly reduce the occurrence and severity of injuries to the hand. The European Standard for motorcycle protective gloves requires testing of component materials separately and does not consider the impact of abrasive surfaces on seems. This work aimed to develop a new method of testing of fully constructed gloves as worn by a rider in impact abrasion situations. It used previously published fall mechanics to understand the areas that may undergo impact abrasion. It defines the important zones for abrasion resistance and details ideal impact/measurement geometry for measurement on a Cambridge type abrasion tester. It proposes a method for the impact abrasion resistance of the palm, knuckles, wrist, outer side of the little finger and the tops of fingers. This information may be used for the quantification of fully manufactured gloves for standard certification or use in a rating system.

Effect of soil texture and wheat plants on N₂O fluxes: a lysimeter study

Agricultural soils are a major source of nitrous oxide (N2O) emissions and an understanding of factors regulating such emissions across contrasting soil types is critical for improved estimation through modelling and mitigation of N2O. In this study we investigated the role of soil texture and its interaction with plants in regulating the N2O fluxes in agricultural systems. A measurement system that combined weighing lysimeters with automated chambers was used to directly compare continuously measured surface N2O fluxes, leaching losses of water and nitrogen and evapotranspiration in three contrasting soils types of the Riverine Plain, NSW, Australia. The soils comprised a deep sand, a loam and a clay loam with and without the presence of wheat plants. All soils were under the same fertilizer management and irrigation was applied according to plant water requirements. In fallow soils, texture significantly affected N2O emissions in the order clay loam > loam > sand. However, when planted, the difference in N2O emissions among the three soils types became less pronounced. Nitrous oxide emissions were 6.2 and 2.4 times higher from fallow clay loam and loam cores, respectively, compared with cores planted with wheat. This is considered to be due to plant uptake of water and nitrogen which resulted in reduced amounts of soil water and available nitrogen, and therefore less favourable soil conditions for denitrification. The effect of plants on N2O emissions was not apparent in the coarse textured sandy soil probably because of aerobic soil conditions, likely caused by low water holding capacity and rapid drainage irrespective of plant presence resulting in reduced denitrification activity. More than 90% of N2O emissions were derived from denitrification in the fine-textured clay loam-determined for a two week period using K15NO3 fertilizer. The proportion of N2O that was not derived from K15NO3 was higher in the coarse-textured sand and loam, which may have been derived from soil N through nitrification or denitrification of mineralized N. Water filled pore space was a poorer predictor of N2O emissions compared with volumetric water content because of variable bulk density among soil types. The data may better inform the calibration of greenhouse gas prediction models as soil texture is one of the primary factors that explain spatial variation in N2O emissions by regulating soil oxygen. Defining the significance of N2O emissions between planted and fallow soils may enable improved yield scaled N2O emission assessment, water and nitrogen scheduling in the pre-watering phase during early crop establishment and within rotations of irrigated arable cropping systems.

Investigation of the mechanism of resistance to glyphosate herbicide in hairy fleaban.

The resistance of weeds to herbicides is a consequence of one or more mechanisms in the plant, responsible for not allowing the herbicide to act properly at the active site.

Modelling water droplet movement on a leaf surface

The central aim for the research undertaken in this PhD thesis is the development of a model for simulating water droplet movement on a leaf surface and to compare the model behavior with experimental observations. A series of five papers has been presented to explain systematically the way in which this droplet modelling work has been realised. Knowing the path of the droplet on the leaf surface is important for understanding how a droplet of water, pesticide, or nutrient will be absorbed through the leaf surface. An important aspect of the research is the generation of a leaf surface representation that acts as the foundation of the droplet model. Initially a laser scanner is used to capture the surface characteristics for two types of leaves in the form of a large scattered data set. After the identification of the leaf surface boundary, a set of internal points is chosen over which a triangulation of the surface is constructed. We present a novel hybrid approach for leaf surface fitting on this triangulation that combines Clough-Tocher (CT) and radial basis function (RBF) methods to achieve a surface with a continuously turning normal. The accuracy of the hybrid technique is assessed using numerical experimentation. The hybrid CT-RBF method is shown to give good representations of Frangipani and Anthurium leaves. Such leaf models facilitate an understanding of plant development and permit the modelling of the interaction of plants with their environment. The motion of a droplet traversing this virtual leaf surface is affected by various forces including gravity, friction and resistance between the surface and the droplet. The innovation of our model is the use of thin-film theory in the context of droplet movement to determine the thickness of the droplet as it moves on the surface. Experimental verification shows that the droplet model captures reality quite well and produces realistic droplet motion on the leaf surface. Most importantly, we observed that the simulated droplet motion follows the contours of the surface and spreads as a thin film. In the future, the model may be applied to determine the path of a droplet of pesticide along a leaf surface before it falls from or comes to a standstill on the surface. It will also be used to study the paths of many droplets of water or pesticide moving and colliding on the surface.