Modelling and control of a floating oscillating water column

A novel numerical model of a Bent Backwards Duct Buoy (BBDB) Oscillating Water Column (OWC) Wave Energy Converter was created based on existing isolated numerical models of the different energy conversion systems utilised by an OWC. The novel aspect of this numerical model is that it incorporates the interdependencies of the different power conversion systems rather than modelling each system individually. This was achieved by accounting for the dynamic aerodynamic damping caused by the changing turbine rotational velocity by recalculating the turbine damping for each simulation sample and applying it via a feedback loop. The accuracy of the model was validated using experimental data collected during the Components for Ocean Renewable Energy Systems (CORES) EU FP-7 project that was tested in Galway Bay, Ireland. During the verification process, it was discovered that the model could also be applied as a valuable tool when troubleshooting device performance. A new turbine was developed and added to a full scale model after being investigated using Computational Fluid Dynamics. The energy storage capacity of the impulse turbine was investigated by modelling the turbine with both high and low inertia and applying three turbine control theories to the turbine using the full scale model. A single Maximum Power Point Tracking algorithm was applied to the low-inertia turbine, while both a fixed and dynamic control algorithm was applied to the high-inertia turbine. These results suggest that the highinertia turbine could be used as a flywheel energy storage device that could help minimize output power variation despite the low operating speed of the impulse turbine. This research identified the importance of applying dynamic turbine damping to a BBDB OWC numerical model, revealed additional value of the model as a device troubleshooting tool, and found that an impulse turbine could be applied as an energy storage system.

Modelling and simulations of ductile iron solidification-induced variations in mechanical behaviour on component and microstructural level

The mechanical behaviour and performance of a ductile iron component is highly dependent on the local variations in solidification conditions during the casting process. Here we show a framework which combine a previously developed closed chain of simulations for cast components with a micro-scale Finite Element Method (FEM) simulation of the behaviour and performance of the microstructure. A casting process simulation, including modelling of solidification and mechanical material characterization, provides the basis for a macro-scale FEM analysis of the component. A critical region is identified to which the micro-scale FEM simulation of a representative microstructure, generated using X-ray tomography, is applied. The mechanical behaviour of the different microstructural phases are determined using a surrogate model based optimisation routine and experimental data. It is discussed that the approach enables a link between solidification- and microstructure-models and simulations of as well component as microstructural behaviour, and can contribute with new understanding regarding the behaviour and performance of different microstructural phases and morphologies in industrial ductile iron components in service.

Semantic relations: Modelling issues, proposals and possible applications

Semantic relations are an important element in the construction of ontology-based linguistic resources and models of problem domains. Nevertheless, they remain under-specified. This is a pervasive problem in both Software Engineering and Artificial Intelligence. Thus, we find semantic links that can have multiple interpretations, abstractions that are not enough to represent the relation richness of problem domains, and even poorly structured taxonomies. However, if provided with precise semantics, some of these problems can be avoided, and meaningful operations can be performed on them that can be an aid in the ontology construction process. In this paper we present some insightful issues about the representation of relations. Moreover, the initiatives aiming to provide relations with clear semantics are explained and the inclusion of their core ideas as part of a methodology for the development of ontology-based linguistic resources is proposed.

Modelling the generation of customised poetry in Jess

The present paper presents an application that composes formal poetry in Spanish in a semiautomatic interactive fashion. JASPER is a forward reasoning rule-based system that obtains from the user an intended message, the desired metric, a choice of vocabulary, and a corpus of verses; and, by intelligent adaptation of selected examples from this corpus using the given words, carries out a prose-to-poetry translation of the given message. In the composition process, JASPER combines natural language generation and a set of construction heuristics obtained from formal literature on Spanish poetry.

Evaluation of deterministic and complex analytical hierarchy process methods for agricultural land suitability analysis in a changing climate

Land suitability analysis is employed to evaluate the appropriateness of land for a particular purpose whilst integrating both qualitative and quantitative inputs, which can be continuous in nature. However, in agricultural modelling there is often a disregard of this contiguous aspect. Therefore, some parametric procedures for suitability analysis compartmentalise units into defined membership classes. This imposition of crisp boundaries neglects the continuous formations found throughout nature and overlooks differences and inherent uncertainties found in the modelling. This research will compare two approaches to suitability analysis over three differing methods. The primary approach will use an Analytical Hierarchy Process (AHP), while the other approach will use a Fuzzy AHP over two methods; Fitted Fuzzy AHP and Nested Fuzzy AHP. Secondary to this, each method will be assessed into how it behaves in a climate change scenario to understand and highlight the role of uncertainties in model conceptualisation and structure. Outputs and comparisons between each method, in relation to area, proportion of membership classes and spatial representation, showed that fuzzy modelling techniques detailed a more robust and continuous output. In particular the Nested Fuzzy AHP was concluded to be more pertinent, as it incorporated complex modelling techniques, as well as the initial AHP framework. Through this comparison and assessment of model behaviour, an evaluation of each methods predictive capacity and relevance for decision-making purposes in agricultural applications is gained.

Dynamical modeling of biogas production supported by an experimental anaerobic digestion process

This paper presents the development of a combined experimental and numerical approach to study the anaerobic digestion of both the wastes produced in a biorefinery using yeast for biodiesel production and the wastes generated in the preceding microbial biomass production. The experimental results show that it is possible to valorise through anaerobic digestion all the tested residues. In the implementation of the numerical model for anaerobic digestion, a procedure for the identification of its parameters needs to be developed. A hybrid search Genetic Algorithm was used, followed by a direct search method. In order to test the procedure for estimation of parameters, first noise-free data was considered and a critical analysis of the results obtain so far was undertaken. As a demonstration of its application, the procedure was applied to experimental data.

On The Use of Genetic Algorithms for Parameter Identification in Anaerobic Digestion Modelling

Anaerobic digestion (AD) of wastewater is a very interesting option for waste valorization, energy production and environment protection. It is a complex, naturally occurring process that can take place inside bioreactors. The capability of predicting the operation of such bioreactors is important to optimize the design and the operation conditions of the reactors, which, in part, justifies the numerous AD models presently available. The existing AD models are not universal, have to be inferred from prior knowledge and rely on existing experimental data. Among the tasks involved in the process of developing a dynamical model for AD, the estimation of parameters is one of the most challenging. This paper presents the identifiability analysis of a nonlinear dynamical model for a batch reactor. Particular attention is given to the structural identifiability of the model, which considers the uniqueness of the estimated parameters. To perform this analysis, the GenSSI toolbox was used. The estimation of the model parameters is achieved with genetic algorithms (GA) which have already been used in the context of AD modelling, although not commonly. The paper discusses its advantages and disadvantages.