Nanocomposites as probes for biodetection by SERS

The present work aimed to explore the potential of new nanocomposites based on carbon nanostructures and metal nanoparticles for the detection of biomolecules through surface enhanced Raman scattering (SERS). In a first step, polyvinyl alcohol composites were prepared incorporating silver nanoparticles by two different reduction procedures. At first without introduction of carbon nanostructures. These composites showed good results for the SERS identification of nucleic acids. Next, the synthesis and characterization of graphene oxide was studied to be used in the preparation of silver and gold nanocomposites. The reduction of this nanomaterial with different chemical agents was explored, since its reduction degree may be a determinant factor for the application envisaged (biomolecules interaction). The preparation of the nanocomposites with silver and gold was performed with different reducing agents. The SERS activity of these new nanocomposites was then explored in the presence of different analytes, varying the experimental conditions for Raman spectra acquisition. It was interesting to verify that the silver containing nanocomposites presented the particularity to intensify the graphene D and G bands. It is also important to highlight that a new eco-friendly reducing agent was tested for the synthesis of the graphene oxide composites, an Eucalyptus Globulus extract. Other variable introduced was the preparation of gold nanostars synthesized with hydroxylamine in the presence of graphene oxide, which allowed the preparation of a new nanocomposite with SERS potential. Fibrous membranes were also prepared by electrospinning with the aim to prepare SERS supports with adequate topography and porosity for the formation of nanoparticles agglomerates for the creation of the so-called hot-spots and also to allow the penetration of the analyte molecules. The polymers polyvinyl alcohol and polyacrylonitrile were selected for electrospinning. Using this technique, electrospun mantles with silver and gold nanoparticles and nanocomposites were prepared. Several variables were studied, such as the introduction of the nano-fillers during the electrospinning process, later deposition of the nano-fillers on the simple electrospun polymeric fibres and surface functionalization of the simple polymeric membranes to link the nano-fillers. At last, the potentialities of using carbon nanotubes forests, produced by chemical vapor deposition and coated with gold film by sputtering, as new SERS substrates were explored. It was found that the SERS detection of DNA bases and ADN itself is possible using these substrates.

Treatment of aqueous effluents contaminated with ionic liquids

Ionic liquids are a class of solvents that, due to their unique properties, have been proposed in the past few years as alternatives to some hazardous volatile organic compounds. They are already used by industry, where it was possible to improve different processes by the incorporation of this kind of non-volatile and often liquid solvents. However, even if ionic liquids cannot contribute to air pollution, due to their negligible vapour pressures, they can be dispersed thorough aquatic streams thus contaminating the environment. Therefore, the main goals of this work are to study the mutual solubilities between water and different ionic liquids in order to infer on their environmental impact, and to propose effective methods to remove and, whenever possible, recover ionic liquids from aqueous media. The liquid-liquid phase behaviour of different ionic liquids and water was evaluated in the temperature range between (288.15 and 318.15) K. For higher melting temperature ionic liquids a narrower temperature range was studied. The gathered data allowed a deep understanding on the structural effects of the ionic liquid, namely the cation core, isomerism, symmetry, cation alkyl chain length and the anion nature through their mutual solubilities (saturation values) with water. The experimental data were also supported by the COnductor-like Screening MOdel for Real Solvents (COSMO-RS), and for some more specific systems, molecular dynamics simulations were also employed for a better comprehension of these systems at a molecular level. On the other hand, in order to remove and recover ionic liquids from aqueous solutions, two different methods were studied: one based on aqueous biphasic systems, that allowed an almost complete recovery of hydrophilic ionic liquids (those completely miscible with water at temperatures close to room temperature) by the addition of strong salting-out agents (Al2(SO4)3 or AlK(SO4)2); and the other based on the adsorption of several ionic liquids onto commercial activated carbon. The first approach, in addition to allowing the removal of ionic liquids from aqueous solutions, also makes possible to recover the ionic liquid and to recycle the remaining solution. In the adsorption process, only the removal of the ionic liquid from aqueous solutions was attempted. Nevertheless, a broad understanding of the structural effects of the ionic liquid on the adsorption process was attained, and a final improvement on the adsorption of hydrophilic ionic liquids by the addition of an inorganic salt (Na2SO4) was also achieved. Yet, the development of a recovery process that allows the reuse of the ionic liquid is still required for the development of sustainable processes.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Estudos de síntese e transformação de cromonas e 4-quinolonas

Esta dissertação está dividida em duas partes. Na primeira parte reportam-se métodos de síntese de (E)-3-estirilflavonas e (E)/(Z)-2-aril- 4-cloro-3-estiril-2H-cromenos e estudos de ciclização das (E)-3- estirilflavonas em 5-arilbenzo[c]xantonas. Na segunda parte desenvolveram-se novas rotas de síntese de (E)-2-aril-3-estiril-4- quinolonas e posterior transformação em 5-fenil-12- metilbenzo[c]acridonas e 2,4-diarilfuro[3,2-c]quinolinas. Nesta parte estudou-se também a transformação de 2-aril-4-cloro-1,2-dihidroquinolina- 1,3-dicarbaldeídos em (E)/(Z)-2-aril-4-cloro-3-estiril-1,2- di-hidroquinolina-1-carbaldeídos. A síntese de novos derivados de (E)-3-estirilflavonas, abordada na primeira parte desta dissertação, envolveu estudos de otimização da reação de bromação seguida de ciclização de 3-aril-1-(2- hidroxiaril)propano-1,3-dionas/3-aril-3-hidroxi-1-(2-hidroxiaril)prop-2- en-1-onas em 3-bromoflavonas e o desenvolvimento de uma nova rota de síntese de 3-metilflavonas. As 3-metilflavonas foram sujeitas a bromação e seguidamente transformadas em sais de fosfónio antes de serem utilizadas na síntese de (E)-3-estirilflavonas via reação de Wittig. As 3-bromoflavonas foram também usadas na síntese de (E)-3- estirilflavonas via reação de Heck. A síntese de novos derivados de (E)/(Z)-2-aril-4-cloro-3-estiril-2H-cromenos, via reação de Wittig, envolveu a síntese e formilação de flavanonas. A última transformação reportada na primeira parte desta dissertação é a síntese de 5-arilbenzo[c]xantonas por reação de eletrociclização seguida de oxidação de (E)-3-estirilflavonas. Na segunda parte desta dissertação são estudadas duas vias de síntese de 2-aril-1-metil-4-quinolonas. A primeira via de síntese envolve a síntese de N-(2-acetilfenil)benzamidas, sua ciclização em 4-quinolonas seguida de metilação destas. A segunda via envolve a metilação e ciclização de N-(2-acetilfenil)benzamidas obtendo-se, num só passo, as 2-aril-1-metil-4-quinolonas. Posterior iodação das 2-aril-1-metil-4- quinolonas e subsequente reação de Heck das 2-aril-3-iodo-1-metil-4- quinolonas com estirenos comerciais possibilitaram a síntese de (E)-2- aril-3-estiril-1-metil-4-quinolonas. Estudos de eletrociclização seguidos de oxidação das (E)-2-aril-3-estiril-1-metil-4-quinolonas utilizando uma lâmpada de UV de mercúrio de alta pressão possibilitou a síntese de 5- fenil-12-metilbenzo[c]acridonas, enquanto que o aquecimento em refluxo de 1,2,4-triclorobenzeno deu origem a 2,4-diarilfuro[3,2- c]quinolinas. Nesta segunda parte aborda-se também a síntese de 2-aril-4-cloro-1,2- di-hidroquinolina-1,3-dicarbaldeídos, a partir da formilação de 2-aril- 2,3-di-hidro-4-quinolonas e a sua transformação em (E)/(Z)-2-aril-4- cloro-3-estiril-1,2-di-hidroquinolina-1-carbaldeídos por reação de Wittig. Todos os compostos sintetizados foram caracterizados por espectroscopia de ressonância magnética nuclear de protão e carbono 13C, espectros bidimensionais de correlação heteronuclear (HMBC e HSQC) e, nalguns casos espectros de efeito nuclear Overhauser (NOESY). Os novos produtos foram igualmente caracterizados por espectrometria de massa e sempre que possível análise elementar ou espectrometria de massa de alta resolução.

A computational study of ionic liquids used in the production of fuels and biofuels

For the past decades it has been a worldwide concern to reduce the emission of harmful gases released during the combustion of fossil fuels. This goal has been addressed through the reduction of sulfur-containing compounds, and the replacement of fossil fuels by biofuels, such as bioethanol, produced in large scale from biomass. For this purpose, a new class of solvents, the Ionic Liquids (ILs), has been applied, aiming at developing new processes and replacing common organic solvents in the current processes. ILs can be composed by a large number of different combinations of cations and anions, which confer unique but desired properties to ILs. The ability of fine-tuning the properties of ILs to meet the requirements of a specific application range by mixing different cations and anions arises as the most relevant aspect for rendering ILs so attractive to researchers. Nonetheless, due to the huge number of possible combinations between the ions it is required the use of cheap predictive approaches for anticipating how they will act in a given situation. Molecular dynamics (MD) simulation is a statistical mechanics computational approach, based on Newton’s equations of motion, which can be used to study macroscopic systems at the atomic level, through the prediction of their properties, and other structural information. In the case of ILs, MD simulations have been extensively applied. The slow dynamics associated to ILs constitutes a challenge for their correct description that requires improvements and developments of existent force fields, as well as larger computational efforts (longer times of simulation). The present document reports studies based on MD simulations devoted to disclose the mechanisms of interaction established by ILs in systems representative of fuel and biofuels streams, and at biomass pre-treatment process. Hence, MD simulations were used to evaluate different systems composed of ILs and thiophene, benzene, water, ethanol and also glucose molecules. For the latter molecules, it was carried out a study aiming to ascertain the performance of a recently proposed force field (GROMOS 56ACARBO) to reproduce the dynamic behavior of such molecules in aqueous solution. The results here reported reveal that the interactions established by ILs are dependent on the individual characteristics of each IL. Generally, the polar character of ILs is deterministic in their propensity to interact with the other molecules. Although it is unquestionable the advantage of using MD simulations, it is necessary to recognize the need for improvements and developments of force fields, not only for a successful description of ILs, but also for other relevant compounds such as the carbohydrates.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.

Photodegradation of sertraline by solar radiation and influencing factors

Photodegradation is considered to be one of the most important processes of elimination of pharmaceutical drugs from natural water matrices. The high consumption and discharge of these substances, in particular antidepressants, to the aquatic environment supports the need to study degradation processes. This dissertation aimed at studying the direct and indirect photodegradation of sertraline, an antidepressant known for its persistence in the environment, and the evaluation of the influence of environmentally relevant factors in its photodegradation. The photodegradation experiments were developed under simulated solar light and the irradiation times converted to summer sunny days (SSD), an equivalent time in natural environmental conditions. The direct photodegradation was evaluated in solutions of sertraline prepared in ultrapure water and the indirect photodegradation was studied through the addition of photosensitizers (humic substances, Fe(III), nitrates and oxygen). Further irradiation studies were perfomed in aqueous samples collected from two wastewater treatment plants, Vouga river and Ria de Aveiro. The samples were chemically characterized (dissolved organic carbon, nitrates and nitrites and iron determination and UV/Vis spectroscopy). The quantification of sertraline was done by HPLC-UV and photoproducts from direct photodegradation were identified by electrospray mass spectrometry. An observed direct photodegradation rate of sertraline of 0.0062 h-1 was determined, corresponding to a half-life time of 111 h (equivalent to 29 SSD). A significant influence of photosensitizers was observed, the best results being achieved in irradiations of sertraline with humic acids, obtaining a half-life time of 12 h. This was attributed to the hydrophobicity of this substance and higher absortivity in the UV/Vis wavelength, which promote processes of indirect photodegradation. The degradation of sertraline in natural samples was also enhanced comparatively to the direct photodegradation, achieving half-life times between 10 and 25h; the best results were achieved in samples from the primary treatment of a wastewater treatment plant and Ria de Aveiro, with half-life times of 10 and 16 h, respectively. A total of six photoproducts formed during the direct photodegradation of sertraline were identified, three of which were not yet identified in the literature. The main factors contributing to the degradation of sertraline were analysed but this was not fully accomplished, requiring further studies of the composition of the natural matrices and the combined influence of distinct photosensitizers during the irradiation. Nevertheless, it was concluded that the photodegradation of sertraline is greatly influenced by indirect photodegradation processes, promoted by the presence of photosensitizers.

Physiology and metabolic profile of Moringa olifera and Eucalyptus globulus plants subjected to climate changes

As alterações climáticas emergentes têm um grande impacto no crescimento e desenvolvimento de espécies florestais, nomeadamente em espécies de valor industrial e medicinal, como é o caso do eucalipto (Eucalyptus globulus) e da moringa (Moringa oleifera). Assim, é urgente conhecer as respostas fisiológicas e entender as variações que ocorrem nos perfis metabólicos de espécies vegetais. Neste trabalho, plantas jovens de Eucalyptus globulus foram expostas a radiação UVB (12kJ/m2) e foram avaliadas as respostas fisiológicas e o perfil metabólico, um e onze dias após a aplicação da radiação. A dose de UVB usada não afetou as reações fotoquímicas nem as trocas gasosas, contudo ao nível do metabolismo do carbono (AST e amido) e do conteúdo de pigmentos verificaram-se pequenas alterações (AST e pigmentos). Através da análise do perfil metabólico de E. globulus foram encontrados compostos voláteis e semi-voláteis pertencentes às famílias dos terpenos, sesquiterpenos e aldeídos. Em geral, os sesquiterpenos e os álcoois monoterpénicos apresentaram uma tendência para manter e, em alguns casos, diminuir com o stress, enquanto que o grupos dos aldeídos aumentou e os monoterpenos apresentaram um comportamento mais heterogéneo. O E. globulus mostrou ser uma espécie tolerante à aplicação da dose de UVB usada neste trabalho. Por outro lado, plantas jovens de M. oleifera foram expostas a défice hídrico (DH). Um grupo de plantas foi recolhido um dia após o final da exposição e o outro grupo após onze dias do final da exposição. Foi avaliado o perfil metabólico desta espécie através de GC/MS. Os dados cromatográficos indicaram que em condições de stress (DH(1) e DH(11)), as quantidades de compostos associados a vias primárias e secundárias de defesa (como os alcanos, álcoois, ácidos carboxílicos, esteróis, aminoácidos e açucares) sofreram algumas alterações. As plantas analisadas 11 dias após a remoção do stress mostraram maiores variações do perfil de metabolitos. No entanto, tanto um como onze dias após a remoção do stress, as plantas apresentaram a formação de novos rebentos. Apesar do perfil de metabolitos ter sofrido algumas alterações, por não se registarem casos de morte, conclui-se que as plantas de moringa mostraram ser tolerantes aos tratamentos aplicados.

A interface carboneto de silício-solução aquosa e o enchimento por barbotina

Neste trabalho estudaram-se as interfaces carboneto de silício-solução aquosa e carbono-solução aquosa, com vista a uma melhor compreensão dos processos de floculaçáo e desfloculaçáo de suspensões de cada um daqueles materiais e de suas misturas. Os pós foram caracterizados por recurso a técnicas de sedimentação, microscopia electrónica de varrimento, difracçáo de raios-X, análises térmicas, espectroscopia de infra-vermelhos e picnometria de hélio. As suspensões foram caracterizadas por técnicas de microelectroforese, sedimentação e reologia. Estudou-se a influência de algumas variáveis mais importantes do processo de enchimento por barbotina como, por exemplo, o mecanismo e o grau de estabilização das suspensões, a concentração de sólidos, a distribuição granulométrica das partículas, e o tempo de envelhecimento das suspensões, na estrutura das partículas em suspensão e nas características dos corpos conformados por enchimento por barbotina. A cinética deste processo foi estudada sob o efeito de pressão aplicada e relacionada com a estrutura das partículas em suspensão e com a microstrutura dos corpos em verde. Estudaram-se os mecanismos da segregação de tamanhos de partículas em suspensão que ocorre durante o processo de enchimento por barbotina devidos aos efeitos da gravidade e da obstrução do bolo pelas partículas finas. Discutiram-se os domínios das variáveis do processo em que cada um daqueles efeitos é dominante e propôs-se um novo modelo para o fenómeno da segregação por efeito de obstrução capaz de interpretar os resultados observados neste trabalho e os encontrados na literatura. Estabeleceram-se correlações estreitas entre as variáveis do processo de enchimento por barbotina, a microestrutura dos corpos conformados e o seu comportamento durante a etapa da secagem. Procurou ainda avaliar-se a capacidade do enchimento por barbotina para preparar materiais compósitos de carboneto de silício e carbono com características adequadas para a sinterizaçáo reactiva.