Preparação e caracterização de vidros contendo nanopartículas de Ag

This work consists of preparation and characterization of glasses containing transition noble metals and the study of optical properties of such materials. The glasses were prepared by quenching of the glass melt followed by heat treatment and polishing of the monoliths. The structural characterization of glasses was made using differential thermal analysis, X-ray, Raman and infrared spectroscopies, while the optical properties were studied by UV-Vis and M-Lines spectroscopies. Preliminary results have shown that the color of the glasses is dependent on both concentration of silver and the melting temperature of the melt. Controlled heat treatments have been used to induce the crystallization of Ag nanoparticles within the glass. The study of crystallization was accompanied by electron microscopy and UV-Vis spectroscopy. Data from electron diffraction, as well as chemical analysis, EDX, were obtained using a transmission electron microscope. EDX data have shown that the atomic percentage of Ag is higher on the nanoparticle. X-ray diffraction was used in order to characterize the composition of the crystals and cubic AgCl was identified as the main crystallized nanophase obtained after annealing

Vitrocerâmicas para blindagens balísticas

The use of ceramic materials in ballistic armor is considerable. Such materials can be very harder and lighter than metallic materials commonly used and it presents advantages to replace metallic materials when necessary toughness can be achieved. However, as SiC and Al2O3 ceramic, traditionally used for shielding, still have high manufacturing cost or low density do not have enough to shield applications such as aircraft. An alternative is the glass-ceramics, ceramics obtained by controlled crystallization of glasses, whose properties can be adjusted by choosing the chemical composition of glass, heat treatment of crystallization and special treatments such as ion exchange on the surface, resulting in increased mechanical strength . The objective of this project is to study the kinetics of crystallization of a glass composition based on cordierite (2MgO.2Al2O3.5SiO2), low density and high hardness, for the manufacture of glass-ceramics for ballistic tests. Shown in this report are results of heat treatment of crystallization and characterization by thermal analysis (DSC) glass obtained previously, indicating uneven distribution of crystals, and drying, weighing, mixing of raw materials and a new fusion of glass, the same composition

Redução de consumo de energia eletrica a partir de reaproveitamento de energia termica com uso de ciclo rankine orgânico

This paper is proposed the usage of an Organic Rankine Cycle (ORC) along with waste heat recovery from an inconstant heat source. This method of waste heat recovery with intermittent heat source is part of a technical viability study. This paper also brings up the usage of thermal energy storage as heat source for the ORC. This paper is based on a heat treatment company study in which a natural gas furnace is explored. Data such as mass flow, temperature and specific waste gas heat from this furnace are used through calculations. Calculations are made also based on furnace cycles. This viability study considers a series of working fluids such as ammonia, benzene, R113 and R134a. Results point out that ORC with out thermal storage and using refrigerant fluid ammonia is the best alternative

Estudo sobre fornos de tratamento térmico e propostas de cogeração de energia em usina siderurgica não integrada

Steel industry is a sector heavily dependent on energy, both electrical and thermal. Since the receipt of raw materials to the shipment of finished products to customers, through mergers, casting, rolling, heat treatment, inspection, among others, high amounts of energy are demanded, generating very significant costs to the productive chain in its entirety . Therefore, any alternative that favors the reduction in energy consumption or barateie the cost of this is very welcome. Within this context, this paper aims to make a technical and economic analysis of installing a cogeneration plant in the field rolling in a non-integrated steel mill. Two configurations are proposed plants, with one being the use of heat from waste gases from furnaces existing in the area mentioned and another with the use of heat from waste gases from an internal combustion engine. Both proposals are evaluated technically and later is done the economic analysis, calculating the financial return (pay back) in relation to the investment required, operation and maintenance of the plant

Caracterização da liga do sistema binário Ti-15Mo para aplicações biomedicas

As they have excellent mechanical properties, corrosion resistance and biocompatibility, much research has been conducted with respect to biomedical applications of titanium alloys. This work aims to study the experimental system binary alloy Ti-15Mo, in the raw state of fusion and heat treatment after homogenization, solubilization and calcination (simulating conditions employed for nanotube growth) targeting biomedical applications. Samples were obtained by casting the components in an electric arc furnace with inert atmosphere of argon. After obtaining the alloy, it was heat treated at three different heat treatments, namely homogenizing, calcining and simulation solubilization. The phases present were analyzed by X-ray diffraction, optical microscopy and microhardness testing

Crescimento de apatita na superfície da liga Ti-25Ta empregando dois tipos de tratamento de superfície: biomimético e deposição de polímero por eletrofiação

Titanium and its alloys has been widely used as materials for metallic biomaterials implants are usually employed to restore the hard tissue function, being used for artificial joints and bones, synthetic plates, crowns, dental implants and screws . Objective of this work was the surface modification of Ti-alloy 25Ta from biomimetic surface treatment of employment and deposition of polymer by electrospinning. The league was obtained from the fusion of the pure elements in the arc furnace with controlled atmosphere. The ingots were subjected to heat treatment, cold forged and sectioned discs with 13 mm diameter and 3 mm thick. Two surface treatments was evaluated, biomimetic and electrospinning with PCL fiber. The biomimetic treatment was performed involving alkaline treatment for three molarities 1.5M, 3M and 5M with immersion in SBF. The electrospinning was performed using PCL polymer alloy surface after the alkali treatment Ti25Ta 1M. For this group the polymer coated surfaces were immersed in calcium phosphate containing solution for immobilization of apatite. The results were compared with previous studies using surface treatment group to verify hydroxyapatite formation on the sample surface and it is concluded that the best condition is biomimetic treatment with 5M alkali treatment and heat treatment at 80 ° C for 72 hours

Desenvolvimento de recobrimento submicrométrico de óxido de nióbio para aplicação em tubulações de prospecção de petróleo

Pós-graduação em Engenharia Mecânica - FEG

Estudo do desempenho de filmes de Ti02 como aceptor de elétrons e obtenção de fases puras de nanopartículas de Ti02: anatase e rutila, sintetizado por uma nova rota química

Pós-graduação em Ciência dos Materiais - FEIS

Efeito de protocolos de cimentação na carga de fratura para uma cerâmica de dissilicato de lítio

Pós-graduação em Odontologia Restauradora - ICT

Síntese e caracterização estrutural de pigmentos cerâmicos a base de cromita por método químico

The ceramic pigments are colored inorganic substances that during the process of dispersion in the ceramic glazes and subsequent calcination, are stable against physical and chemical attack. Therefore, they are crystalline compounds applied in the ceramic industry for coloring vitreous base. In this study, the Pechini method was used for obtaining the pigment CuCr2O4 with heat treatment at the temperatures of 800, 900 and 1000 ° C. The powder pigments were characterized on their structural, morphological and colorimetric aspects. The thermal analysis conducted on an amorphous precursor in a TG / DTA indicates the weight loss in the entire temperature range investigated, with characteristic exothermic peak of the elimination of the organic composition of the precursor around 300°C. The development of the crystalline phases were investigated by XRD, using a diffractometer with Cu Ka radiation and graphite monochromator, where it was observed the presence of crystalline phases corresponding to Cr2O3 and CuCr2O4.The measurements of the specific surface area of the powders pigments were carried out in an equipment Micromeritcs, model ASAP 2000, using N2 as gas of adsorption/desorption. The colorimetric measurements of the pigments were made in a colorimeter Gretac Macbeth Color-eye spectrophotometer 2180 / 2180UV in CIELAB standards. Based on the obtained results, it can be verified the thermal stability of the powder pigments of green coloration, which enables it as an alternative to the materials currently used in the manufacture of ceramic tiles.

White Light and Multicolor Emission Tuning in Triply Doped Yb3+/Tm3+/Er3+ Novel Fluoro-phosphate Transparent Glass-ceramics

New Yb3+, Er3+ and Tm3+ doped fluoro-phosphate glasses belonging to the system NaPO3–YF3–BaF2–CaF2 and containing up to 10 wt% of rare-earth ion fluorides were prepared and characterized by differential scanning calorimetry, absorption spectroscopy and up-conversion emission spectroscopy under excitation with a 975 nm laser diode. Transparent and homogeneous glass-ceramics have been reproducibly obtained with a view to manage the red, green and blue emission bands and generate white light. X-ray diffraction as well as electron microscopy techniques have confirmed the formation of fluorite-type cubic nanocrystals at the beginning of the crystallization process while complex nanocrystalline phases are formed after a longer heat-treatment. The prepared glass-ceramics exhibit high optical transparency even after 170 h of thermal treatment. An improvement of up-conversion emission intensity – from 10 to 160 times larger – was measured in the glass-ceramics when compared to the parent glass, suggesting an important incorporation of the rare-earth ions into the crystalline phase(s). The involved mechanisms and lifetime were described in detail as a function of heat-treatment time. Finally, a large range of designable color rendering (from orange to turquoise through white) can be observed in these materials by controlling the laser excitation power and the crystallization rate.

Effectiveness inactivation of trypsin inhibitor fron brazilian cultivarof beans (Phaseolus vulgaris L.)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito da limpeza pós-condicionamento e do tratamento térmico do silano na resistência de união de um cimento resinoso à cerâmica

Pós-graduação em Odontologia - FOA

Efeito do tratamento térmico em cerâmica feldspáticas silanizada na adesão do cimento resinoso

Pós-graduação em Odontologia Restauradora - ICT

Aços avançados de alta resistência: avaliação da microestrutura e propriedades dos aços DP 600 E DP 780

This work aims to study the Dual-Phase 600 and 780 steels, which are part of technology development project materials for the automotive industry. It is worth underscoring the antagonistic properties as the Dual-Phase steel assemble, high mechanical strength and elongation due its microstructure, ferrite and martensite. These properties are obtained by a intercritical heat treatment which facilitates the formation of a hardness metastable microstructure shaped plates of low carbon steels. The applicability of Dual Phase steel in the structure of vehicles is huge and its production is already on a commercial scale, so the study and development of this material implies lower cost in automobile manufacturing processes. The dual phase steels DP600 and DP780 underwent tensile, hardness and metallographic analysis to evaluate and comparing its properties. The results indicate that the DP780 steel has higher strength and hardness than the DP600 steel and its microstructure consists of martensite higher fraction which accounts for the higher resistance and hardness. However, the DP600 has higher conformability to DP780 steel