Examination of process to develop a framework for better implementation of quality practices in building projects

Quality, as well as project success, in construction projects should be capable of being regarded as the fulfillment of expectation of those contributors and stakeholders involved in such projects. Although a significant amount of quality practices have been introduced within the industry, establishment and attainment of reasonable levels of quality internationally in construction projects continues to be an ongoing problem. To date, some investigation into the introduction and improvement of quality practices and stakeholder management in the construction industry has been accomplished independently, but so far no major studies have been completed that examine comprehensively how quality management practices that particularly concentrate on the stakeholders’ perspective of quality can be used to contribute to final project quality outcomes. This paper aims to examine the process for development of a framework for better involvement of stakeholders in quality planning and practices and subsequently to contribute to higher quality outcomes within construction projects. Through extensive literature review it highlights various perceptions of quality, categorizes quality issues with particular focus on benefits and shortcomings and also examines stakeholders’ viewpoint of project quality in order to promote the improvement of outcomes throughout a project’s lifecycle. It proposes a set of arranged information as a basis for development of prospective framework which ultimately aims to improve project quality outcomes. The subsequent framework that will be developed from this research will provide project managers and owners with the required information and strategic direction to achieve their own and their stakeholders’ targets for implementation of quality practices and achievement of high quality outcomes on their future projects.

Available evidence does not support routine administration of antipyretics to reduce duration of fever or illness

Commentary on : Carey JV. Literature review : should antipyretic therapies routinely be administered to patients with [corrected] fever? J Clin Nurs 2010;19:2377–93.

Independent cinema in the Chinese film industry

Chinese independent cinema has developed for more than twenty years. Two sorts of independent cinema exist in China. One is underground cinema, which is produced without official approvals and cannot be circulated in China, and the other are the films which are legally produced by small private film companies and circulated in the domestic film market. This sort of ‘within-system’ independent cinema has played a significant role in the development of Chinese cinema in terms of culture, economics and ideology. In contrast to the amount of comment on underground filmmaking in China, the significance of ‘within-system’ independent cinema has been underestimated by most scholars. This thesis is a study of how political management has determined the development of Chinese independent cinema and how Chinese independent cinema has developed during its various historical trajectories. This study takes media economics as the research approach, and its major methods utilise archive analysis and interviews. The thesis begins with a general review of the definition and business of American independent cinema. Then, after a literature review of Chinese independent cinema, it identifies significant gaps in previous studies and reviews issues of traditional definition and suggests a new definition. After several case studies on the changes in the most famous Chinese directors’ careers, the thesis shows that state studios and private film companies are two essential domestic backers for filmmaking in China. After that, the body of the thesis provides an examination of the development of ‘within-system’ independent cinema. Specifically, three factors: government intervention, the majors’ performance (state studios and, later, the conglomerates) and the market conduct of independent cinema at various points in their trajectories are studied. The key findings of the study are as follows: First, most scholars have overlooked the existence and the significance of within-system Chinese independent cinema. Drawing on an American definition of the independent sector, this thesis proposes a definition of the sector in China: namely, any film that has not been financed, produced, and/or distributed by majors. The thesis also notes important contradictions in applying this definition: i.e. film-making is still dependent on policies that frame industry development. The thesis recognises that major tensions apply to filmmaking in China, which significantly differentiates the Chinese independents from those in the US. Second, the development of Chinese independent cinema is the result the rise of the private sector and the decline of the state studio system. As state studios encountered difficulties the private sector moved forward; consequently the environment improved for independent cinema. Third, before 2003, the film industry in China had little commercialisation. The government controlled independent cinema by means of license and censorship. State studios produced main melody films and Hollywood attracted most of the audiences. Many independent filmmakers focused on commercial films, thus contributing to film commercialisation. Fourth, after 2003, the film industry became increasingly fragmented. The government created distribution and exhibition opportunities for main melody films; conglomerates collaborated with Hong Kong players; Hong Kong co-productions and Hollywood occupied the film market; and small private film companies produced main melody films in order to earn meagre profits. The original contribution of the thesis is to advance the study of Chinese independent cinema. The study suggests a reasonable and practical definition of Chinese independent cinema. It shows how the Chinese government authorities have implemented economic measures to gain ideological control in the film industry. Finally, this the first study on Chinese independent cinema applying a synthesis of economic, political and historical perspectives.

A conceptual decision-making framework for the delivery of innovative change in organisations

Research found that today’s organisations are increasingly aware of the potential barriers and perceived challenges associated with the successful delivery of change — including cultural and sub-cultural indifferences; financial constraints; restricted timelines; insufficient senior management support; fragmented key stakeholder commitment; and inadequate training. The delivery and application of Innovative Change (see glossary) within a construction industry organisation tends to require a certain level of ‘readiness’. This readiness is the combination of an organisation’s ability to part from undertakings that may be old, traditional, or inefficient; and then being able to readily adopt a procedure or initiative which is new, improved, or more efficient. Despite the construction industry’s awareness of the various threats and opportunities associated with the delivery of change, research found little attention is currently given to develop a ‘decision-making framework’ that comprises measurable elements (dynamics) that may assist in more accurately determining an organisation’s level of readiness or ability to deliver innovative change. To resolve this, an initial Background Literature Review in 2004 identified six such dynamics, those of Change, Innovation, Implementation, Culture, Leadership, and Training and Education, which were then hypothesised to be key components of a ‘Conceptual Decision-making Framework’ (CDF) for delivering innovative change within an organisation. To support this hypothesis, a second (more extensive) Literature Review was undertaken from late 2007 to mid 2009. A Delphi study was embarked on in June 2008, inviting fifteen building and construction industry members to form a panel and take part in a Delphi study. The selection criterion required panel members to have senior positions (manager and above) within a recognised field or occupation, and to have experience, understanding and / or knowledge in the process of delivering change within organisations. The final panel comprised nine representatives from private and public industry organisations and tertiary / research and development (R&D) universities. The Delphi study developed, distributed and collated two rounds of survey questionnaires over a four-month period, comprising open-ended and closed questions (referred to as factors). The first round of Delphi survey questionnaires were distributed to the panel in August 2008, asking them to rate the relevancy of the six hypothesised dynamics. In early September 2008, round-one responses were returned, analysed and documented. From this, an additional three dynamics were identified and confirmed by the panel as being highly relevant during the decision-making process when delivering innovative change within an organisation. The additional dynamics (‘Knowledge-sharing and Management’; ‘Business Process Requirements’; and ‘Life-cycle Costs’) were then added to the first six dynamics and used to populate the second (final) Delphi survey questionnaire. This was distributed to the same nine panel members in October 2008, this time asking them to rate the relevancy of all nine dynamics. In November 2008, round-two responses were returned, analysed, summarised and documented. Final results confirmed stability in responses and met Delphi study guidelines. The final contribution is twofold. Firstly, findings confirm all nine dynamics as key components of the proposed CDF for delivering innovative change within an organisation. Secondly, the future development and testing of an ‘Innovative Change Delivery Process’ (ICDP) is proposed, one that is underpinned by an ‘Innovative Change Decision-making Framework’ (ICDF), an ‘Innovative Change Delivery Analysis’ (ICDA) program, and an ‘Innovative Change Delivery Guide’ (ICDG).

Consumers’ intentions to adopt 3G in regional cities in China : a comparative study

Rapid mobile technological evolution and the large economic stake in commercial development of mobile technological innovation make it necessary to understand consumers' motivations towards the latest advanced and updated technologies and services. 3G (the third generation of mobile communication technology) recently started its commercial development in the world‘s largest mobile communication market, China, after being delayed for a few years. Although China fell behind in commercially developing 3G, it is difficult to ignore studying this area, given the size of the market and promising future developments. This market deserves focused research attention, especially in terms of consumer behaviour towards the adoption of mobile technological innovation. Thus, the program of research in this thesis was designed to investigate how Chinese consumers respond to the use of this newly launched mobile technological innovation, with a focus on what factors affect their 3G adoption intentions. It aimed to yield important insights into Chinese consumers‘ innovation adoption behaviours and to contribute to marketing and innovation adoption research. Furthermore, it has been documented that Chinese consumers vary widely between regions in dialect, lifestyle, culture, purchasing power and consumption attitudes. Based on economic development and local culture, China can be divided geographically into distinctive regional consumer markets. Consequently, the results of consumer behaviour research in one region may not necessarily be extrapolated to other regions. In order to better understand Chinese consumers, the disparities between regions should not be overlooked. Therefore, another objective of this program of research was to examine regional variances in consumers' innovation adoption, specifically to identify the similarities and differences in factors influencing 3G adoption, contributing to intra-cultural studies. An extensive literature review identified two gaps: current China-based innovation adoption research studies are limited in providing adequate prediction and explanation of Chinese consumers' intentions to adopt 3G; and there was limited knowledge about the differences between regional Chinese consumers in innovation adoption. Two research questions therefore were developed to address these gaps: 1) What factors influence Chinese consumers' intentions to adopt 3G? 2) How do Chinese consumers differ between regional markets in the relative influence of the factors in determining their intentions to adopt 3G? In accordance with postpositivist research philosophy, two studies were designed to answer the research questions, using mixed methods. To meet the research objectives, the two studies were both conducted in three regional cities, namely Beijing, Shanghai and Wuhan, centred in the three regions of North China, East China and Central China respectively, with sufficient cultural and economical regional variances. Study One was an exploratory study with qualitative research methods. It involved 45 in-depth interviews in the three research cities to gain rich insights into the research context from natural settings. Eight important concepts related to 3G adoption were generated from analysis of the interview data, namely utilitarian expectation, hedonic expectation, status gains, status loss avoidance, normative influence, external influence, cost and quality concern. The concepts of social loss avoidance and quality concern were two unique findings, whereas the other concepts were similar to the findings in Western innovation adoption studies. Moreover, variances in 3G adoption between three groups of regional consumers were also identified, focusing on the perceptions of two concepts, namely status gains and normative influence. The conceptual research model was then developed incorporating the eight concepts plus the dependent variable of adoption intention. The hypothesized relationships between the nine constructs and hypotheses about the differences between regional consumers in 3G adoption were informed by the findings of Study One and the literature reviewed. Study Two was a quantitative study involving a web-based survey and statistical analysis procedure. The web-based survey attracted 800 residents from the three research cities, 270 from Beijing, 265 from Shanghai and 265 from Wuhan. They comprised three research samples for this study and consequently three sets of data were obtained. The data was analysed by Structural Equation Modelling together with Multi-group Analysis. The analysis confirmed that the concepts generated in Study One were influential factors affecting Chinese consumers' 3G adoption intention, with the exception of the concept external influence. Differences were found between the samples in the three research cities in the effect of hedonic expectation, status gains, status loss avoidance and normative influence on 3G adoption intention. The two Studies undertaken in this thesis contributed a better understanding of Chinese consumers' intentions to adopt advanced mobile technological innovation, namely 3G, in three regional markets. This knowledge contributes to innovation adoption and intra-cultural research, as well as consumer behaviour theory. It is also able to inform international and domestic telecommunication companies to develop and deliver more effective marketing strategies across Chinese regional markets. Limitations in the research were identified in terms of the sampling techniques used and the design of the two Studies. Future research was suggested in other Chinese regional markets and into consumer adoption of other types of mobile technological innovations.

The impact of software-as-a-service on business models of leading software vendors : experiences from three exploratory case studies

The number of software vendors offering ‘Software-as-a-Service’ has been increasing in recent years. In the Software-as-a-Service model software is operated by the software vendor and delivered to the customer as a service. Existing business models and industry structures are challenged by the changes to the deployment and pricing model compared to traditional software. However, the full implications on the way companies create, deliver and capture value are not yet sufficiently analyzed. Current research is scattered on specific aspects, only a few studies provide a more holistic view of the impact from a business model perspective. For vendors it is, however, crucial to be aware of the potentially far reaching consequences of Software-as-a-Service. Therefore, a literature review and three exploratory case studies of leading software vendors are used to evaluate possible implications of Software-as-a-Service on business models. The results show an impact on all business model building blocks and highlight in particular the often less articulated impact on key activities, customer relationship and key partnerships for leading software vendors and show related challenges, for example, with regard to the integration of development and operations processes. The observed implications demonstrate the disruptive character of the concept and identify future research requirements.

The psychosocial factors influencing aggressive driving behaviour

Many drivers in highly motorised countries believe that aggressive driving is increasing. While the prevalence of the behaviour is difficult to reliably identify, the consequences of on-road aggression can be severe, with extreme cases resulting in property damage, injury and even death. This research program was undertaken to explore the nature of aggressive driving from within the framework of relevant psychological theory in order to enhance our understanding of the behaviour and to inform the development of relevant interventions. To guide the research a provisional ‘working’ definition of aggressive driving was proposed encapsulating the recurrent characteristics of the behaviour cited in the literature. The definition was: “aggressive driving is any on-road behaviour adopted by a driver that is intended to cause physical or psychological harm to another road user and is associated with feelings of frustration, anger or threat”. Two main theoretical perspectives informed the program of research. The first was Shinar’s (1998) frustration-aggression model, which identifies both the person-related and situational characteristics that contribute to aggressive driving, as well as proposing that aggressive behaviours can serve either an ‘instrumental’ or ‘hostile’ function. The second main perspective was Anderson and Bushman’s (2002) General Aggression Model. In contrast to Shinar’s model, the General Aggression Model reflects a broader perspective on human aggression that facilitates a more comprehensive examination of the emotional and cognitive aspects of aggressive behaviour. Study One (n = 48) examined aggressive driving behaviour from the perspective of young drivers as an at-risk group and involved conducting six focus groups, with eight participants in each. Qualitative analyses identified multiple situational and person-related factors that contribute to on-road aggression. Consistent with human aggression theory, examination of self-reported experiences of aggressive driving identified key psychological elements and processes that are experienced during on-road aggression. Participants cited several emotions experienced during an on-road incident: annoyance, frustration, anger, threat and excitement. Findings also suggest that off-road generated stress may transfer to the on-road environment, at times having severe consequences including crash involvement. Young drivers also appeared quick to experience negative attributions about the other driver, some having additional thoughts of taking action. Additionally, the results showed little difference between males and females in the severity of behavioural responses they were prepared to adopt, although females appeared more likely to displace their negative emotions. Following the self-reported on-road incident, evidence was also found of a post-event influence, with females being more likely to experience ongoing emotional effects after the event. This finding was evidenced by ruminating thoughts or distraction from tasks. However, the impact of such a post-event influence on later behaviours or interpersonal interactions appears to be minimal. Study Two involved the quantitative analysis of n = 926 surveys completed by a wide age range of drivers from across Queensland. The study aimed to explore the relationships between the theoretical components of aggressive driving that were identified in the literature review, and refined based on the findings of Study One. Regression analyses were used to examine participant emotional, cognitive and behavioural responses to two differing on-road scenarios whilst exploring the proposed theoretical framework. A number of socio-demographic, state and trait person-related variables such as age, pre-study emotions, trait aggression and problem-solving style were found to predict the likelihood of a negative emotional response such as frustration, anger, perceived threat, negative attributions and the likelihood of adopting either an instrumental or hostile behaviour in response to Scenarios One and Two. Complex relationships were found to exist between the variables, however, they were interpretable based on the literature review findings. Factor analysis revealed evidence supporting Shinar’s (1998) dichotomous description of on-road aggressive behaviours as being instrumental or hostile. The second stage of Study Two used logistic regression to examine the factors that predicted the potentially hostile aggressive drivers (n = 88) within the sample. These drivers were those who indicated a preparedness to engage in direct acts of interpersonal aggression on the road. Young, male drivers 17–24 years of age were more likely to be classified as potentially hostile aggressive drivers. Young drivers (17–24 years) also scored significantly higher than other drivers on all subscales of the Aggression Questionnaire (Buss & Perry, 1992) and on the ‘negative problem orientation’ and ‘impulsive careless style’ subscales of the Social Problem Solving Inventory – Revised (D’Zurilla, Nezu & Maydeu-Olivares, 2002). The potentially hostile aggressive drivers were also significantly more likely to engage in speeding and drink/drug driving behaviour. With regard to the emotional, cognitive and behavioural variables examined, the potentially hostile aggressive driver group also scored significantly higher than the ‘other driver’ group on most variables examined in the proposed theoretical framework. The variables contained in the framework of aggressive driving reliably distinguished potentially hostile aggressive drivers from other drivers (Nagalkerke R2 = .39). Study Three used a case study approach to conduct an in-depth examination of the psychosocial characteristics of n = 10 (9 males and 1 female) self-confessed hostile aggressive drivers. The self-confessed hostile aggressive drivers were aged 24–55 years of age. A large proportion of these drivers reported a Year 10 education or better and average–above average incomes. As a group, the drivers reported committing a number of speeding and unlicensed driving offences in the past three years and extensive histories of violations outside of this period. Considerable evidence was also found of exposure to a range of developmental risk factors for aggression that may have contributed to the driver’s on-road expression of aggression. These drivers scored significantly higher on the Aggression Questionnaire subscales and Social Problem Solving Inventory Revised subscales, ‘negative problem orientation’ and ‘impulsive/careless style’, than the general sample of drivers included in Study Two. The hostile aggressive driver also scored significantly higher on the Barrett Impulsivity Scale – 11 (Patton, Stanford & Barratt, 1995) measure of impulsivity than a male ‘inmate’, or female ‘general psychiatric’ comparison group. Using the Carlson Psychological Survey (Carlson, 1982), the self-confessed hostile aggressive drivers scored equal or higher scores than the comparison group of incarcerated individuals on the subscale measures of chemical abuse, thought disturbance, anti-social tendencies and self-depreciation. Using the Carlson Psychological Survey personality profiles, seven participants were profiled ‘markedly anti-social’, two were profiled ‘negative-explosive’ and one was profiled as ‘self-centred’. Qualitative analysis of the ten case study self-reports of on-road hostile aggression revealed a similar range of on-road situational factors to those identified in the literature review and Study One. Six of the case studies reported off-road generated stress that they believed contributed to the episodes of aggressive driving they recalled. Intense ‘anger’ or ‘rage’ were most frequently used to describe the emotions experienced in response to the perceived provocation. Less frequently ‘excitement’ and ‘fear’ were cited as relevant emotions. Notably, five of the case studies experienced difficulty articulating their emotions, suggesting emotional difficulties. Consistent with Study Two, these drivers reported negative attributions and most had thoughts of aggressive actions they would like to take. Similarly, these drivers adopted both instrumental and hostile aggressive behaviours during the self-reported incident. Nine participants showed little or no remorse for their behaviour and these drivers also appeared to exhibit low levels of personal insight. Interestingly, few incidents were brought to the attention of the authorities. Further, examination of the person-related characteristics of these drivers indicated that they may be more likely to have come from difficult or dysfunctional backgrounds and to have a history of anti-social behaviours on and off the road. The research program has several key theoretical implications. While many of the findings supported Shinar’s (1998) frustration-aggression model, two key areas of difference emerged. Firstly, aggressive driving behaviour does not always appear to be frustration driven, but can also be driven by feelings of excitation (consistent with the tenets of the General Aggression Model). Secondly, while the findings supported a distinction being made between instrumental and hostile aggressive behaviours, the characteristics of these two types of behaviours require more examination. For example, Shinar (1998) proposes that a driver will adopt an instrumental aggressive behaviour when their progress is impeded if it allows them to achieve their immediate goals (e.g. reaching their destination as quickly as possible); whereas they will engage in hostile aggressive behaviour if their path to their goal is blocked. However, the current results question this assertion, since many of the hostile aggressive drivers studied appeared prepared to engage in hostile acts irrespective of whether their goal was blocked or not. In fact, their behaviour appeared to be characterised by a preparedness to abandon their immediate goals (even if for a short period of time) in order to express their aggression. The use of the General Aggression Model enabled an examination of the three components of the ‘present internal state’ comprising emotions, cognitions and arousal and how these influence the likelihood of a person responding aggressively to an on-road situation. This provided a detailed insight into both the cognitive and emotional aspects of aggressive driving that have important implications for the design of relevant countermeasures. For example, the findings highlighted the potential value of utilising Cognitive Behavioural Therapy with aggressive drivers, particularly the more hostile offenders. Similarly, educational efforts need to be mindful of the way that person-related factors appear to influence one’s perception of another driver’s behaviour as aggressive or benign. Those drivers with a predisposition for aggression were more likely to perceive aggression or ‘wrong doing’ in an ambiguous on-road situation and respond with instrumental and/or hostile behaviour, highlighting the importance of perceptual processes in aggressive driving behaviour.

Politics and school education in Australia : a case of shifting purposes

Purpose – The paper aims to argue that there has been a privileging of the private (social mobility) and economic (social efficiency) purposes of schooling at the expense of the public (democratic equality) purposes of schooling. Design/methodology/approach – The paper employs a literature review, policy and document analysis. Findings – Since the late 1980s, the schooling agenda in Australia has been narrowed to one that gives primacy to purposes of schooling that highlight economic orientations (social efficiency) and private purposes (social mobility). Practical implications – The findings have wider relevance beyond Australia, as similar policy agendas are evident in many other countries raising the question as to how the shift in purposes of education in those countries might mirror those in Australia. Originality/value – While earlier writers have examined schooling policies in Australia and noted the implications of managerialism in relation to these policies, no study has analysed these policies from the perspective of the purposes of schooling. Conceptualising schooling, and its purposes in particular, in this way refocuses attention on how societies use their educational systems to promote (or otherwise) the public good.

Implementing dance in a Queensland primary school : a descriptive case study

This research documents and analyses the modes of implementation of the Dance component of The Arts Essential Learnings in a Queensland school. The research identifies what makes good practice in dance education and the multiple modes of implementation that support this practice. The primary purpose of this research is to describe the factors that influence dance education, as it is delivered, in a Queensland primary school to inform the development of further support for primary teachers and to improve the quality of dance education in Prep -7 schooling. The literature review investigates dance education both in Queensland, Australia and internationally, identifying current issues related to the delivery of dance in a primary school environment including barriers to implementation of dance, authentic learning and integrated approaches to learning. Based on Engestrom.s reformulation of Vygotsky.s theory of socially mediated learning, the implementation of dance education curriculum was explored through descriptive case study method. The case study was conducted in a regional Queensland school identified as delivering the dance curriculum in a variety of ways. The research project provided opportunities to observe, document and analyse how teachers deal with pedagogical dilemmas and solve logistical problems associated with teaching the dance component of the Arts curriculum in this school. Teachers. practices were contextualised through investigation of the whole school context of dance curriculum development. The findings revealed a range of teaching approaches that influenced teachers. interpretation and children.s experience of the dance curriculum. The features of a supportive whole school and cultural environment for dance were identified. These have been captured in a reworked version of Engestrom.s Second Generation Activity Theory that can be applied to the implementation of dance education in primary schools.

The importance of organisational culture to improve a project selection process : case of public infrastructure project in Indonesia

Project selection is a decision-making process that is not merely influenced by technical aspects but also by the people who involved in the process. Organisational culture is described as a set of values and norms that are shared by people within the organisation that affects the way they interact with each other and with stakeholders from outside the organisation. The aim of this paper is to emphasize the importance of organisational culture on improving the quality of decisions in the project selection process, in addition to the influence of technical aspects of a project. The discussion is based on an extensive literature review and, as such, represents the first part of a research agenda investigating the impact of organisational culture on the project selection process applicable specifically to road infrastructure contracts. Four existing models of organisational culture (Denison 1990; Cameron and Quinn 2006; Hofstede 2001; Glaser et al 1987) are discussed and reviewed in view of their use in the larger research project to investigate the impact of culture on identified critical elements of decision-making. An understating of the way organisational culture impacts on project selection will increase the likelihood in future of relevant government departments selecting projects that achieve their stated organisational goals.

Development and evaluation of the Clinician Suicide Risk Assessment Checklist

This paper describes the development and evaluation of a new instrument - the Clinician Suicide Risk Assessment Checklist (CSRAC). The instrument assesses the clinician's competency in three areas: clinical interviewing, assessment of specific suicide risk factors, and formulating a management plan. A draft checklist was constructed by integrating information from 1) literature review 2) expert clinician focus group and 3) consultation with experts. It was utilised in a simulated clinical scenario with clinician trainees and a trained actor in order to test for inter-rater agreement. Agreement was calculated and the checklist was re-drafted with the aim of maximising agreement. A second phase of simulated clinical scenarios was then conducted and inter-rater agreement was calculated for the revised checklist. In the first phase of the study, 18 of 35 items had inadequate inter-rater agreement (60%>), while in the second phase, using the revised version, only 3 of 39 items failed to achieve adequate inter-rater agreement. Further evidence of reliability and validity are required. Continued development of the CSRAC will be necessary before it can be utilised to assess the effectiveness of risk assessment training programs.

Industrial JIG measurements : survey measurements assisting QUT motorsport

This paper outlines our literature review background, investigation and practical application utilizing a precise optical survey level and total station technology for a specialist industrial measurement application. The practical part of the project was to measure and check specific critical features of the Industrial JIG assembly table used by the Queensland University of Technology (QUT) Motorsport group. The JIG is used in constructing a new Formula SAE race-car frame each year and is used throughout the racing season to check the production frame for twists, bends and potential stresses. The industrial JIG table required two survey approaches, firstly determination of the overall flatness throughout its’ steel base surface. Secondly was the validation of verticality of the steel uprights used to support and hold the race-car frame in place during construction and checking alignment for key suspension components. In addition the investigation brings realisations that there are far more accurate, efficient and economical technologies to be harnessed in industrial metrology.

A methodology to assess the competitiveness of real estate developers in China

Real estate, or property development, is considered one of the pillar industries of the Chinese economy. As a result of the opening up of the economy as well as the "macro-control" policy of the Central Chinese Government to moderate the frenetic pace of growth of the economy, the real estate industry has faced fierce competition and ongoing change. Real estate firms in China must improve their competitiveness in order to maintain market share or even survive in this brutally competitive environment. This study developed a methodology to evaluate the competitiveness of real estate developers in the China and then used a case study to illustrate the effectiveness of the evaluation method. Four steps were taken to achieve this. The first step was to conduct a thorough literature review which included a review of the characteristics of real estate industry, theories about competitiveness and the competitive characteristics of real estate developers. Following this literature review, the competitive model was developed based on seven key competitive factors (the 'level 1') identified in the literature. They include: (1) financial competency; (2) market share; (3) management competency; (4) social responsibility; (5) organisational competency; (6) technological capabilities; and, (7) regional competitiveness. In the next step of research, the competitive evaluation criteria (the 'level 2') under each of competitive factors (the 'level 1') were evaluated. Additionally, there were identified a set of competitive attributes (the 'level 3') under each competitive criteria (the 'level 2'). These attributes were initially recognised during the literature review and then expanded upon through interviews with multidisciplinary experts and practitioners in various real estate-related industries. The final step in this research was to undertake a case study using the proposed evaluation method and attributes. Through the study of an actual real estate development company, the procedures and effectiveness of the evaluation method were illustrated and validated. Through the above steps, this research investigates and develops an analytical system for determining the corporate competitiveness of real estate developers in China. The analytical system is formulated to evaluate the "state of health" of the business from different competitive perspectives. The result of empirical study illustrates that a systematic and structured evaluation can effectively assist developers in identifying their strengths and highlighting potential problems. This is very important for the development of an overall corporate strategy and supporting key strategic decisions. This study also provides some insights, analysis and suggestions for improving the competitiveness of real estate developers in China from different perspectives, including: management competency, organisational competency, technological capabilities, financial competency, market share, social responsibility and regional competitiveness. In the case study, problems were found in each of these areas, and they appear to be common in the industry. To address these problems and improve the competitiveness and effectiveness of Chinese real estate developers, a variety of suggestions are proposed. The findings of this research provide an insight into the factors that influence competitiveness in the Chinese real estate industry while also assisting practitioners to formulate strategies to improve their competitiveness. References for studying the competitiveness of real estate developers in other countries are also provided.

Properties of lignin and poly(hydroxybutyrate) blends

The Queensland University of Technology (QUT) allows the presentation of a thesis for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of Seven published/submitted papers and one poster presentation, of which five have been published and the other two are under review. This project is financially supported by the QUTPRA Grant. The twenty-first century started with the resurrection of lignocellulosic biomass as a potential substitute for petrochemicals. Petrochemicals, which enjoyed the sustainable economic growth during the past century, have begun to reach or have reached their peak. The world energy situation is complicated by political uncertainty and by the environmental impact associated with petrochemical import and usage. In particular, greenhouse gasses and toxic emissions produced by petrochemicals have been implicated as a significant cause of climate changes. Lignocellulosic biomass (e.g. sugarcane biomass and bagasse), which potentially enjoys a more abundant, widely distributed, and cost-effective resource base, can play an indispensible role in the paradigm transition from fossil-based to carbohydrate-based economy. Poly(3-hydroxybutyrate), PHB has attracted much commercial interest as a plastic and biodegradable material because some its physical properties are similar to those of polypropylene (PP), even though the two polymers have quite different chemical structures. PHB exhibits a high degree of crystallinity, has a high melting point of approximately 180°C, and most importantly, unlike PP, PHB is rapidly biodegradable. Two major factors which currently inhibit the widespread use of PHB are its high cost and poor mechanical properties. The production costs of PHB are significantly higher than for plastics produced from petrochemical resources (e.g. PP costs $US1 kg-1, whereas PHB costs $US8 kg-1), and its stiff and brittle nature makes processing difficult and impedes its ability to handle high impact. Lignin, together with cellulose and hemicellulose, are the three main components of every lignocellulosic biomass. It is a natural polymer occurring in the plant cell wall. Lignin, after cellulose, is the most abundant polymer in nature. It is extracted mainly as a by-product in the pulp and paper industry. Although, traditionally lignin is burnt in industry for energy, it has a lot of value-add properties. Lignin, which to date has not been exploited, is an amorphous polymer with hydrophobic behaviour. These make it a good candidate for blending with PHB and technically, blending can be a viable solution for price and reduction and enhance production properties. Theoretically, lignin and PHB affect the physiochemical properties of each other when they become miscible in a composite. A comprehensive study on structural, thermal, rheological and environmental properties of lignin/PHB blends together with neat lignin and PHB is the targeted scope of this thesis. An introduction to this research, including a description of the research problem, a literature review and an account of the research progress linking the research papers is presented in Chapter 1. In this research, lignin was obtained from bagasse through extraction with sodium hydroxide. A novel two-step pH precipitation procedure was used to recover soda lignin with the purity of 96.3 wt% from the black liquor (i.e. the spent sodium hydroxide solution). The precipitation process is presented in Chapter 2. A sequential solvent extraction process was used to fractionate the soda lignin into three fractions. These fractions, together with the soda lignin, were characterised to determine elemental composition, purity, carbohydrate content, molecular weight, and functional group content. The thermal properties of the lignins were also determined. The results are presented and discussed in Chapter 2. On the basis of the type and quantity of functional groups, attempts were made to identify potential applications for each of the individual lignins. As an addendum to the general section on the development of composite materials of lignin, which includes Chapters 1 and 2, studies on the kinetics of bagasse thermal degradation are presented in Appendix 1. The work showed that distinct stages of mass losses depend on residual sucrose. As the development of value-added products from lignin will improve the economics of cellulosic ethanol, a review on lignin applications, which included lignin/PHB composites, is presented in Appendix 2. Chapters 3, 4 and 5 are dedicated to investigations of the properties of soda lignin/PHB composites. Chapter 3 reports on the thermal stability and miscibility of the blends. Although the addition of soda lignin shifts the onset of PHB decomposition to lower temperatures, the lignin/PHB blends are thermally more stable over a wider temperature range. The results from the thermal study also indicated that blends containing up to 40 wt% soda lignin were miscible. The Tg data for these blends fitted nicely to the Gordon-Taylor and Kwei models. Fourier transform infrared spectroscopy (FT-IR) evaluation showed that the miscibility of the blends was because of specific hydrogen bonding (and similar interactions) between reactive phenolic hydroxyl groups of lignin and the carbonyl group of PHB. The thermophysical and rheological properties of soda lignin/PHB blends are presented in Chapter 4. In this chapter, the kinetics of thermal degradation of the blends is studied using thermogravimetric analysis (TGA). This preliminary investigation is limited to the processing temperature of blend manufacturing. Of significance in the study, is the drop in the apparent energy of activation, Ea from 112 kJmol-1 for pure PHB to half that value for blends. This means that the addition of lignin to PHB reduces the thermal stability of PHB, and that the comparative reduced weight loss observed in the TGA data is associated with the slower rate of lignin degradation in the composite. The Tg of PHB, as well as its melting temperature, melting enthalpy, crystallinity and melting point decrease with increase in lignin content. Results from the rheological investigation showed that at low lignin content (.30 wt%), lignin acts as a plasticiser for PHB, while at high lignin content it acts as a filler. Chapter 5 is dedicated to the environmental study of soda lignin/PHB blends. The biodegradability of lignin/PHB blends is compared to that of PHB using the standard soil burial test. To obtain acceptable biodegradation data, samples were buried for 12 months under controlled conditions. Gravimetric analysis, TGA, optical microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), FT-IR, and X-ray photoelectron spectroscopy (XPS) were used in the study. The results clearly demonstrated that lignin retards the biodegradation of PHB, and that the miscible blends were more resistant to degradation compared to the immiscible blends. To obtain an understanding between the structure of lignin and the properties of the blends, a methanol-soluble lignin, which contains 3× less phenolic hydroxyl group that its parent soda lignin used in preparing blends for the work reported in Chapters 3 and 4, was blended with PHB and the properties of the blends investigated. The results are reported in Chapter 6. At up to 40 wt% methanolsoluble lignin, the experimental data fitted the Gordon-Taylor and Kwei models, similar to the results obtained soda lignin-based blends. However, the values obtained for the interactive parameters for the methanol-soluble lignin blends were slightly lower than the blends obtained with soda lignin indicating weaker association between methanol-soluble lignin and PHB. FT-IR data confirmed that hydrogen bonding is the main interactive force between the reactive functional groups of lignin and the carbonyl group of PHB. In summary, the structural differences existing between the two lignins did not manifest itself in the properties of their blends.

Barriers to information transfer for multi-trauma patients upon discharge from the Emergency Department in a tertiary level hospital

Purpose: Communication is integral to effective trauma care provision. This presentation will report on barriers to meaningful information transfer for multi-trauma patients upon discharge from the Emergency Department (ED) to the care areas of Intensive Care Unit, High Dependency Unit, and Perioperative Services. This is an ongoing study at one tertiary level hospital in Queensland. Method: This is a multi-phase, mixed method study. In Phase 1 data were collected about information transfer. This Phase was initially informed by a comprehensive literature review, then via focus groups, chart audit, staff survey and review of national and international trauma forms. Results: The barriers identified related to nursing handover, documented information, time inefficiency, patient complexity and stability and time of transfer. Specifically this included differences in staff expectations and variation in the nursing handover processes, no agreed minimum dataset of information handed over, missing, illegible or difficult to find information in documentation (both medical and nursing), low compliance with some forms used for documentation. Handover of these patients is complex with information coming from many sources, dealing with issues is more difficult for these patients when transferred out of hours. Conclusions and further directions: This study investigated the current communication processes and standards of information transfer to identify barriers and issues. The barriers identified were the structure used for documentation, processes used (e.g. handover), patient acuity and time. This information is informing the development, implementation and evaluation of strategies to ameliorate the issues identified.