Mesh selectivity for spotted seer, Scomberomorus guttatus (Bloch & Schneider)

An attempt has been made to evolve a suitable mesh size for the commercially significant size group of S. guttatus. To obtain maximum sustainable yield taking biological factors also into consideration, 52 mm mesh bar nets are suggested for exploiting the fishery on both the East coasts of India.

Selectivity of gill nets for Scomberomorus commersoni

Selectivity of gill nets for S. commersoni was studied with nets made of 4 different mesh sizes fabricated with 4 different specifications of nylon twines. Fishing operations were conducted off Cochin through the fishing seasons 1968-72. The commercially significant size group of S. commersoni was found to fall in the length range of 850-950 mm. The optimum mesh size required for the capture of this group of S. commersoni was estimated as 76 mm. bar in nylon twine 210/12/3. The relationship between the twine size and mesh size was also worked out.

Discriminant analysis for mesh selectivity studies

Discriminant analysis takes into consideration the natural correlation existing between different characteristics of fish when studying mesh selectivity. Some specimen data are presented for two different sets of fish and it is shown that the discriminant analysis shows a significant difference between the two sets where F test failed.

Fishing gear selectivity of Lates niloticus L. (Nile perch), Oreochromis niloticus L. (Nile tilapia) and Rastrineobola argentea Pellegrin (Mukene) in lakes Victoria, Kyoga and Nabugabo

Catch effort data on which fisheries management regulations are sometimes based are not available for most lakes in Uganda. However, failure to regulate fishing gears and methods has been a major cause of collapse of fisheries in the country. Fisheries have been damaged by destructive and non-selective fishing gears and methods such as trawling and beach seining, by use of gill nets of mesh size which crop immature fish and by introduction of mechanised fishing. Selectivity of the gears used to crop Lates niloticus 1. (Nile perch), Oreochromis niloticus 1. (Nile tilapia) and Rastrineobola argentea (Mukene) which are currently the most important commercial species in Uganda were examined in order to recommend the most suitable types, sizes and methods that should be used in exploiting these fisheries . Gill nets of less than 127 mm mainly cropped immature Nile ti1apia and Nile perch. To protect these fisheries, the minimum mesh size of gill nets should be set at 127 mm. Seine nets of 5 mm do catch high proportions of immature Mukene while those of 10 mm catch mainly mature Mukene. When operated inshore, both sizes catch immature Nile perch and Nile ti1apia as by-catch. To protect the Mukene fishery and avoid catching immature byecatch, a minimum mesh size of the Mukene net should have been 10 mm operated as Lampara type net offshore but since most fishennen have been using the 5 mm seine for over five years the minimum size should not be allowed to drop below 5 mm pending further thorough investigations. Beach seining, trawling and are destructive to fisheries and should be prohibited until data that may justify their use is available.

Fishing gear selectivity in relation to their manufacture and to the management of fisheries of the Nile perch, the Nile tilapia, and Rastrineobola argentea (Mukene) in Lakes Victoria and Kyoga

The fisheries of Lakes Victoria and Kyoga have changed from the native tilapiine species and are now dominated by two introduced species; Nile perch and Nile tilapia, and one native species; Rastrineobola argentea (mukene). Because of the differences in the size of the species, it may be necessary to change the type and sizes of nets used.

A solid-phase microextraction fiber coated with diglycidyloxycalix[4]arene yields very high extraction selectivity and sensitivity during the analysis of chlorobenzenes in soil

A novel fiber coated with novel sol-gel (5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene/hydroxy-terminated silicone oil; diglycidyloxy-C[4]/OH-TSO) was prepared for use with headspace solid-phase microextraction (HS-SPME) combined with gas chromatography (GC) and electron capture detection (ECD), which was applied in order to determine nine chlorobenzenes in soil matrices. Due to the improved fiber preparation, which increases the percentage of calixarene in the coating, the new calixarene fiber exhibits very high extraction selectivity and sensitivity to chlorine-substituted compounds. Various parameters affecting the extraction efficiency were optimized in order to maximize the sensitivity during the chlorobenzene analysis. Interferences from different soil matrices with different characteristics were investigated, and the amount extracted was strongly influenced by the matrix. Therefore, a standard addition protocol was performed on the real soil samples. The linear ranges of detection for the chlorobenzenes tested covered three orders of magnitude, and correlation coefficients > 0.9976 and relative standard deviations (RSD) < 8% were observed. The detection limits were found at sub-ng/g of soil levels, which were about an order of magnitude lower than those given by the commercial poly(dimethylsiloxane) (PDMS) coating for most of the compounds. The recoveries ranged from 64 to 109.6% for each analyte in the real kaleyard soil matrix when different concentration levels were determined over the linear range, which confirmed the reliability and feasibility of the HS-SPME/GC-ECD approach using the fiber coated with diglycidyloxy-C[4]/OH-TSO for the ultratrace analysis of chlorobenzenes in complex matrices.

WG-like modes selectivity in a square cavity with posts

We investigate the characteristics of Whispering-Gallery(WG)-like modes in a square cavity with posts by employing the two-dimentional (2D) finite-difference time-domain (FDTD) technique combined with the effective index method. The results indicate that the posts can result in mode selection in the WG-like modes. The WG-like modes with odd mode numbers are not much sensitive to the sizes of the posts. However, the quality factor (i.e. Q-factor) of the WG-like modes with even mode numbers decreases sharply with the increasing size of the posts. The decreasing Q-factor is attributed to mode leakage and scattering loss due to the presence of the post. The mode selection increases with the mode spacing of square cavity twice in an optimized strucure.

Shape selectivity in methane dehydroaromatization over Mo/MCM-22 catalysts during a lifetime experiment

Dehydroaromatization of CH4 with 2% CO2 on 6Mo/MCM-22 in a 100-h lifetime test was carried out at 993 K, atmospheric pressure and 1500 mL/gh. The duration of the lifetime test can be divided into an induction stage, stable stage and deactivation stage on the basis of the selectivities of hydrocarbons and coke. The characteristics of deposited coke with different time onstream were studied using TPO and TG techniques. There were two peaks corresponding to two kinds of coke recorded in TPO profiles, and the oxidation temperature of coke shifted to higher values with less hydrogen content with the increase of coke deposits. BET and Benzene-TPD techniques were employed to study the variation of specific surface area of the external and micropore surface versus time onstream. With the accumulation of coke deposits, although the pores became partially blocked and the internal surface decreased, methane could still enter the channel and was converted to benzene with shape selectivity until a critical value of coke deposition was reached.