Avaliação da recalcitrância e toxicidade de lixiviado bruto e tratado por processos primário e secundário.

Um dos grandes problemas enfrentados no tratamento de lixiviado é a definição de suas características físico-químicas e biológicas. Neste contexto, o objetivo do presente trabalho é avaliar a composição química, a recalcitrância, e a toxicidade do lixiviado bruto e tratado por processos de tratamento (físico-químico e biológico) oriundo do Aterro Metropolitano de Gramacho, localizado no município de Duque de Caxias, no estado do Rio de Janeiro. Os resultados mostraram maior biodegradabilidade aeróbia no efluente físico-químico com percentuais variando de 7% a 35 %. A natureza de tais compostos justifica a natureza refratária do lixiviado e alerta pela toxicidade que podem atribuir tanto aos microrganismos envolvidos no processo quanto a saúde humana quando dispostos incorretamente. Para o lixiviado em estudo, observou-se a diminuição da toxicidade ao passar pelo processo físicoquímico. Dessa maneira, observou-se que é necessário a adoção de sistemas de tratamento que conjuguem processos físico-químicos atuando como pré ou pós-tratamento de processos biológicos. Sendo assim, os resultados obtidos mostram a importância deste tipo de caracterização, como fonte de subsídios para a seleção, projeto e avaliação de sistemas de tratamento.

Ensaios de tratabilidade de águas residuárias da indústria de piso de madeira por processos oxidativos avançados: ozônio e UV-C.

A indústria moveleira em geral e de piso de madeira é caracterizada por processos a seco. Em decorrência da limpeza e lavagem de maquinário e superfícies gera águas residuárias em baixos volumes porém altamente contaminadas com substâncias recalcitrantes de difícil tratamento. Com o objetivo de oferecer uma alternativa tecnológica de fácil operação (com uso mínimo de reagentes químicos), capaz de tratar tais águas, reduzir toxicidade e aumentar biodegradabilidade do efluente, viabilizando desta forma uma etapa subsequente de tratamento biológico, o presente trabalho conduziu ensaios de tratabilidade baseados em processos oxidativos avançados com águas residuárias provenientes de lavagens em uma indústria de piso de madeira em Nybro, Suécia, com DQO inicial de aproximadamente 45.000 mg/L e pH de 2,3-2,6. Após tratamento primário in situ com redução de 89% de DQO, os seguintes processos geradores de radicais OH foram testados em escala de laboratório: ozonização sem ajuste de pH (Etapa I); ozonização com ajuste de pH (Etapa II); e ozonização + UV-C com ajuste de pH (Etapa III). Os experimentos foram realizados em semi-batelada, utilizando-se um aparato com dois reatores conectados (de O3 e de UV), entre os quais foi mantido fluxo de recirculação em contracorrente com o gás. Para o desenho experimental, utilizou-se a metodologia de planejamento fatorial do tipo Delineamento Composto Central Rotacional (DCCR) utilizando-se como variáveis independentes, (i) vazão de recirculação entre os reatores (VR) com níveis variando de 0,3 a 3L/min; (ii) concentração de O3 na mistura gasosa injetada ([O3]) ou modo de dosagem cujos níveis variaram de 40 a 115 g/Nm3 e; (iii) pH inicial (Etapas II e III) com níveis que variaram de 3 a 11. A quantidade total de O3 fornecida até o final de cada ensaio foi fixada em 2 gramas de O3 para cada grama de DQO inicial (2:1). A eficiência de cada tratamento foi avaliada em função da redução de DQO, da remoção de COT e do consumo de O3. Para ozonização sem ajuste de pH foram alcançadas reduções de DQO e COT de 65 e 31% respectivamente. No tratamento com ajuste de pH sem UV, foram alcançadas reduções de DQO e COT de 85% e 43% com pHinicial = 7,0 enquanto que no tratamento com UV foi alcançada redução de DQO e COT de 93% e 56% respectivamente, com pHi = 9,38. Os resultados de respirometria com os efluentes dos tratamentos indicaram que a ozonização destas águas em pH baixo pode resultar na geração de subprodutos menos biodegradáveis. Entretanto, tais produtos não são gerados quando a ozonização é realizada em pH mais elevado (7,0), mesmo sem aplicação de UV, com doses de O3:DQOinicial menores que 1:1. O tratamento por ozonização pode, portanto, ser aplicado como uma etapa intermediária de tratamento das águas residuárias em questão, inclusive precedendo o tratamento biológico.

Avaliação da eficiência de wetland construído como unidade de polimento de efluente de tratamento secundário de lixiviado por lodos ativados

Uma das dificuldades a ser enfrentada na implantação de aterros sanitários é o tratamento adequado do lixiviado gerado e seu lançamento no meio ambiente dentro dos padrões estabelecidos pela legislação. O potencial poluidor do lixiviado está ligado principalmente aos altos valores de carga orgânica que promove a redução do oxigênio disponível (utilizado na degradação da matéria orgânica) em cursos dágua, prejudicando a fauna e a flora nesses meios. O objetivo do presente trabalho foi avaliar o sistema de tratamento por wetland construído como unidade de polimento do efluente secundário de uma estação de tratamento de lixiviado de aterro de resíduos sólidos urbanos na Região Metropolitana do Rio de Janeiro. Além dos parâmetros coletivos específicos e não específicos, também foram empregados o fracionamento pelo processo de separação por membranas e ensaios de toxicidade aguda. Os resultados mostram que o wetland tem uma ação positiva como unidade de polimento refletida na redução dos parâmetros turbidez (84%), DQO (19%), amônia (30%) e sólidos totais (3%) reduzindo, assim, os impactos ambientais do lançamento do lixiviado. Contudo, a qualidade do efluente final encontra-se acima dos parâmetros de referência de controle ambiental e mostra a necessidade de um efluente secundário de melhor qualidade. Os resultados mostraram também que altos valores de DQO inerte tanto no afluente (85% em média) quanto no efluente (93,5% em média) do wetland indicam que esses lixiviados apresentam natureza refratária confirmada pelos baixos valores de biodegradabilidade no afluente (20,5% em média) e no efluente (5% em média) do wetland. O fracionamento com membranas mostrou que o afluente e o efluente do wetland possuem maiores contribuições de moléculas na fração >1 kDa. Os ensaios de toxicidade com Aliivibrio fischeri mostraram que o afluente e o efluente do wetland possuem toxicidade aguda, sendo a mesma menor na faixa com moléculas menores.

Preparação, caracterização e avaliação de nanocompósitos de PBAT/amido de milho e vermiculita organofilizada

Nos últimos 20-30 anos polímeros biodegradáveis vêm sendo estudados e desenvolvidos e atualmente já são comercializados. Contudo, o custo, a processabilidade e algumas propriedades ainda dificultam a penetração desses polímeros no mercado e a competição com as chamadas commodities. Não são poucos os autores que se dedicam a desenvolver aditivos e formulações para superar essas limitações. Desta forma, esta Tese se dedicou ao desenvolvimento de compósitos de Ecobras, fabricado pela Basf e comercializado pela Corn Products, utilizando como carga mineral resíduo da extração da bauxita, no município de Santa Luzia/PB, o qual consiste em sua totalidade de vermiculita. Esta vermiculita foi quimicamente modificada com sais de alquil fosfônio para melhorar a compatibilidade com a matriz polimérica e também espaçar as camadas de aluminossilicato. De fato, a modificação com o brometo de hexadecil tributil fosfônio resultou na esfoliação da vermiculita tornando-a potencialmente apropriada para a obtenção de nanocompósitos. A preparação dos compósitos foi realizada pelo método de intercalação no estado fundido e foram comparadas a utilização da câmara interna de mistura e da mini extrusora de dupla rosca, sendo esta última mais eficaz na dispersão da vermiculita, conforme revelado pela microscopia eletrônica de varredura, difração de raios-X e reometria de placas. O grau de dispersão também foi influenciado pela estrutura química do modificador da vermiculita e pelo teor dessa carga incorporada à matriz. Teores mais elevados levaram a formação de aglomerados, enquanto a modificação da carga implicou na formação de micro e nanocompósitos. Ainda houve alterações das propriedades térmicas com aumento dos valores da temperatura de transição vítrea, de cristalização e fusão, embora o grau de cristalinidade tenha sido mantido. Nitidamente, foram obtidos materiais mais rígidos, com maior módulo e menor capacidade de deformação. Cerca de 58% de perda de massa foi observada para os micro e nanocompósitos obtidos após 17 semanas de enterro em solo simulado para avaliação da biodegradabilidade, valor bem próximo ao Ecobras puro. De modo geral, a incorporação das diferentes vermiculitas retardou nas primeiras semanas a biodegradação, provavelmente em função de modificações na estrutura cristalina, conforme sugerido pelos maiores valores de temperatura de fusão observados durante o acompanhamento do processo de biodegradação. No entanto, após 7 semanas os perfis de biodegradação dos micro e nanocompósitos se aproximaram bastante do Ecobras puro. Desta forma, foi possível nesta Tese obter um nanocompósito de Ecobras com vermiculita modificada com brometo de hexadecil fosfônio utilizando ferramentas comuns de processamento no estado fundido com biodegradabilidade próxima ao polímero de partida, porém mais rígido e menos deformável

Cloning and expression of zebra fish ferroportin and investigating its influence on anemia

Iron is required for many microbes and pathogens for their survival and proliferation including Leishmania which cause leishmaniasis. Leishmaniasis is an increasingly serious infectious disease with a wide spectrum of clinical manifestations. These range from localized cutaneous leishmaniasis (CL) lesions to a lethal visceral form. Certain strains such as BALB/c mice fail to control L. major infection and develop progressive lesions and systemic disease. These mice are thought to be a model of non-healing forms of the human disease such as kala-azar or diffuse cutaneous leishmaniasis. Progression of disease in BALB/c mice has been associated with the anemia, in last days of their survival, the progressive anemia is considered to be one of the reasons of their death. Ferroportin (Fpn), a key regulator of iron homeostasis is a conserved membrane protein that exports iron across the duodenal enterocytes as well as macrophages and hepatocytes into the blood circulation. Fpn has also critical influence on survival and proliferation of many microorganisms whose growth is dependent upon iron, thus preparation of Fpn is needed to study the role of iron in immune responses and pathogenesis of micoorganisms. To prepare and characterize a recombinant ferroportin, total RNA was extracted from Indian zebrafish duodenum, and used to synthesize cDNA by RT-PCR. PCR product was first cloned in Topo TA vector and then subcloned into the GFP expression vector pEGFP–N1. The final resulted plasmid (pEGFP-ZFpn) was used for expression of FPN-EGFP protein in Hek 293T cells. The expression was confirmed by fluorescence microscopy and flow cytometery. Recombinant Fpn was further characterized by submission of its predicted amino acid sequences to the TMHMM V2.0 prediction server (hidden Markov model), NetOGlyc 3.1 server and NetNGlyc 3.1 server. Data emphasised that obtained Fpn from indian zebrafish contained eight transmembrane domains with N- and C-termini inside the cytoplasm and harboured 78 mucin-type glycosylated amino acid. The results indicate that the prepared and characterized recombinant Fpn protein has no membrane topology difference compared to other Fpn described by other researcher. Our next aim was to deliver recombinant plasmid (pEGFP-ZFpn) to entrocyte cells. However, naked therapeutic genes are rapidly degraded by nucleases, showing poor cellular uptake, nonspecificity to the target cells, and low transfection efficiency. The development of safe and efficient gene carriers is one of the prerequisites for the success of gene therapy. Chitosan and alginate 139 polymers were used for oral gene carrier because of their biodegradability, biocompatibility and their mucoadhesive and permeability-enhancing properties in the gut. Nanoparticles comprising Alginate/Chitosan polymers were prepared by pregel preparation method. The resulting nanoparticles had a loading efficiency of 95% and average size of 188 nm as confirmed by PCS method and SEM images had showed spherical particles. BALB/c mice were divided to three groups. The first and second group were fed with chitosan/alginate nanoparticles containing the pEGFP-ZFpn and pEGFP plasmid, respectively (30 μgr/mice) and the third group (control) didn’t get any nanoparticles. The result showed BALB/c mice infected by L.major, resulted in higher hematocryte and iron level in pEGFP-ZFpn fed mice than that in other groups. Consentration of cytokines determined by ELISA showed lower levels of IL-4 and IL-10 and higher levels of IFN-γ/IL-4 and IFN-γ/IL-10 ratios in pEGFP-ZFpn fed mice than that in other groups. Morover more limited increase of footpad thickness and significant reduction of viable parasites in lymph node was seen in pEGFP-ZFpn fed mice. The results showed the first group exhibited a highr hematocryte and iron compared to the other groups. These data strongly suggests the in vivo administration of chitosan/alginate nanoparticles containing pEGFP-ZFpn suppress Th2 response and may be used to control the leishmaniasis .

Life cycle assessments of biodegradable, commercial biopolymers - A critical review

Biopolymers are generally considered an eco-friendly alternative to petrochemical polymers due to the renewable feedstock used to produce them and their biodegradability. However, the farming practices used to grow these feedstocks often carry significant environmental burdens, and the production energy can be higher than for petrochemical polymers. Life cycle assessments (LCAs) are available in the literature, which make comparisons between biopolymers and various petrochemical polymers, however the results can be very disparate. This review has therefore been undertaken, focusing on three biodegradable biopolymers, poly(lactic acid) (PLA), poly(hydroxyalkanoates) (PHAs), and starch-based polymers, in an attempt to determine the environmental impact of each in comparison to petrochemical polymers. Reasons are explored for the discrepancies between these published LCAs. The majority of studies focused only on the consumption of non-renewable energy and global warming potential and often found these biopolymers to be superior to petrochemically derived polymers. In contrast, studies which considered other environmental impact categories as well as those which were regional or product specific often found that this conclusion could not be drawn. Despite some unfavorable results for these biopolymers, the immature nature of these technologies needs to be taken into account as future optimization and improvements in process efficiencies are expected. © 2013 Elsevier B.V. All rights reserved.

钻井废水可生化性研究及处理技术探索

钻井废水是油气井开采钻探过程中产生的废水，钻井废水成分复杂，有机物浓度高、色度高、悬浮物浓度高，水质变化大，排放点分散，不经处理排放会污染环境，破坏生态。随着石油工业的不断发展和国家环保法律法规的日益严格，钻井废水的治理也越来越受到重视。如何采用经济有效的方法处理废弃钻井液，对油气井开采业的可持续发展具有重要意义。本论文以遂宁磨153 井的钻井废水为主要研究对象，在对废水进行絮凝沉降预处理和生物法处理探索的基础上，针对钻井废水可生化性差的特点，采用水解酸化和Fenton 试剂改善钻井废水的可生化性，对反应过程进行了比较详细的考察，对可生化性改善的机理进行了探索。主要研究结论如下：1 用PFS 和PAC 配制的混合混凝剂对钻井废水COD 的去除效果比较显著，在最佳条件下COD 的去除率可达75%，且絮体沉降速度较快，出水pH 保持中性；2 水解酸化法处理钻井废水可显著改善废水的可生化性。经48 小时水解酸化处理，钻井废水的理论BOD5可提高约22 倍，表观BOD5/COD值由0.004 提高到0.034。用接触氧化反应器处理经水解酸化处理后的废水，处理效果比较稳定，COD平均去除率达35.5%；3 研究了Fenton反应中各影响因子对废水COD去除率、BOD5/COD的影响并分析其作用机制，确定了最佳条件：初始pH为4.0，H2O2/Fe2+(摩尔浓度比)为20，H2O2/COD（质量浓度比）为1，反应时间为2 个小时。此条件下，废水的COD去除率约为40%，BOD5/COD值从0.002～0.003 提高至0.15～0.2，可生化性得到很大提高。本论文的主要创新点在于：1 以成分复杂、水质变化大的气井钻井废水为研究对象，从理论BOD 和表观BOD 两方面对水解酸化过程中废水可生化性的变化进行了分析；2 对Fenton 试剂改善钻井废水可生化性的过程、主要影响因素进行了比较详细的考察。本论文的研究成果，可为生物法处理钻井废水的深入研究提供理论依据。Drilling wastewater is produced in the process of oil-gas well drilling,because of its complicated composition, high concentrate of organic compound andsuspended solid, high chroma, levity of water quality and decentralization ofdischarge point, it pollutes environment seriously if discharged without treatment.With the development of petroleum industry and the issuing of more strict laws forenvironmental protection, it has been paid more and more attention on drillingwastewater treatment. It is of great importance for the sustainable development ofoil-gas well drilling to treat drilling wastewater by economical and effective methods.In this paper, drilling wastewater of Mo No.153 well in Suining was studied asthe main object. On the basis of research on pre-treatment with flocculant andbiological treatment, and according to the character of poor biodegradability, thedrilling wastewater was treated by hydrolytic acidification and Fenton’s reagent toimprove its biodegradability. The process and mechanism of biodegradabilitychanging were investigated. The primary conclusions are:1 It is effective to treat drilling wastewater with mixing PFS and PAC asflocculant. The removal rates of COD came up to 75% under optimal conditions, thesedimentation rate of flocculation is rapid, and the pH value of treated water remainedneutral;2 The biodegradability of drilling wastewater was highly improved afterhydrolytic acidification process. The theoretic BOD5 of drilling wastewater increasedby 22 times and its detected BOD5/COD ratio increased from 0.004 to 0.034 afterhydrolytic acidification for 48 hours. The wastewater after hydrolytic acidificationwas treated by biological contact oxidation reactor. Stable treatment performance was achieved, and the average removal rates of COD came up to 35.5%;3 The effects of various affection factors on the removal efficiency of COD andBOD5/COD radio in treating drilling wastewater by Fenton’s reagent wereinvestigated and the mechanism was analyzed. The optimal conditions were: initialpH of solution was 4.0, the molar ratio of H2O2 and Fe2+ was 20, the concentrationratio of H2O2 and COD was 1 and the reaction time was 120 min. Under the aboveconditions, the removal efficiency was about 40% and the ratio of BOD5 and CODincreased from 0.002 ¡« 0.003 to 0.15 ¡« 0.2. The biodegradability of drillingwastewater was greatly improved.The innovations of this thesis are:1 The drilling wastewater was taken as the research object which hascomplicated composition and variational water quality, and the changes ofbiodegradability were analyzed from theoretic BOD and detected BOD aspects duringhydrolytic acidification process;2 The biodegradability changing process and primary affection factors of drillingwastewater treating by Fenton’s reagent were investigated.The results of this study could provide theoretic foundation for further researchon biological treatment of drilling wastewater.

超声与磁粉强化含单宁废水生物处理研究

单宁是一种典型的有毒难降解污染物，在制革、造纸、制药、印染等行业废水中广泛存在，对水环境造成污染并且影响废水生物处理效果。本研究针对含单宁废水生物处理效率低、较高浓度时微生物受抑制且污泥容易膨胀等问题，采用超声和磁粉来强化含单宁废水生物处理，研究超声和磁粉对微生物活性、污染物去除及污泥沉降性能的影响，并对其作用机理进行了分析和探讨。 研究结果表明，活性污泥系统中单宁酸容积负荷可以达到1.8kgCOD/(m3·d)，单宁酸和COD去除率分别达到85.2%和79.6%，但如果负荷进一步增大则微生物活性迅速降低。系统在pH 5~8、温度20~35℃、DO>1 mg/L的条件下具有较好的单宁酸降解效果和处理稳定性。单宁降解动力学参数为：μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594。 磁粉对系统处理效果和污泥沉降性能有一定的促进作用，且效果要优于外磁场。适宜的磁粉粒径和投加量分别为0.05~0.15mm和1.0g/L，COD去除率比对照系统提高6.4%，SVI降低28.6%，污泥絮体结构紧密。磁粉强化主要是通过其对污泥菌胶团的凝聚、吸附作用以及对微生物活性的强化作用实现。 在适当强度（0.4W/cm2）和辐照时间（20min）的超声作用下污泥絮体和细胞膜通透性增大，酶分泌也增多，系统的COD去除率比对照提高了8.8%，单宁酶酶活提高了11%。但超声也使污泥絮体结构松散，沉降性能下降，SVI比对照系统升高9.3%。 由于污泥流失加剧导致污泥浓度相对较低，声磁联合强化系统相对于磁粉强化系统其处理效果并没有提高。但相对于单纯活性污泥系统，声磁联合作用下系统处理效果、污泥沉降性能以及系统运行稳定性都得到明显改善。本研究为难降解废水的生物处理提供了一个新的思路。 Tannins are typical refractory and toxic pollutants that commonly exist in wastewater from dye, medicine, paper and leather industries and cause many problems associated with environmental pollution and biological treatment of wastewater. Biological treatment efficiency of tannin-containing wastewater is usually low owing to its biological toxicity and low biodegradability, microbes are usually inhibited under high tannin concentration and sludge bulking frequently occurs. In this study, ultrasound and magnetic powder were used to improve the biological treatment performance of simulated tannic acid-containing wastewater. The effects of ultrasonic irradiation and magnetic powder on microbial activity, tannic acid degradation rate and sludge sedimentation were investigated. The augmentation mechanisms were analyzed and discussed. The experimental results showed that the microbes were prominently inhibited under high tannic acid concentration, but moderate degradation efficiency can be maintained under a tannic acid load of up to 1.8kgCOD/(m3·d), with the tannic acid degradation and COD removal percentage of 85.2% and 79.6% respectively. The highest degradation rates and treatment stability were achieved at pH range of 5~8, temperature range of 20~35℃ and DO concentration of above 1mg/L. The kinetic parameters were estimated, including: μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594. The microbial activity, tannic acid degradation rate and sludge sedimentation were improved by adding Fe3O4 magnetic powder, and the augmentation performance was better than external magnetic field. The appropriate particle size and dosage of magnetic powder were found to be 0.05~0.15mm and 1.0g/L, respectively, under which the COD removal percentage was improved by 6.4% and SVI value decreased by 28.6%, and compact floc structure was observed. This was mainly caused by the flocculation and adsorption effects of magnetic powder against sludge floc and the stimulation of microbial activity under appropriate magnetic field. Under appropriate ultrasonic irradiation (ultrasonic intensity 0.4W/cm2, ultrasonic irradiation time 20min), the permeability of floc and cell membrane are improved, transfer of substrate and oxygen were reinforced; meanwhile, more enzyme were produced by microbes under the slight damage caused by ultrasound. However, the floc structure became loose under ultrasonic irradiation, leading to relatively poor sedimentation, with the SVI value 9.3% higher than the control system. Although the magnetic powder-ultrasonic irradiation combined augmentation system showed no improvement in treatment performance compared with sole magnetic augmentation system owing to its relatively low sludge concentration, it guaranteed the stable operation of system, meanwhile the tannic acid degradation and sludge sedimentation were significantly improved compared with sole activated sludge system. This study gives a new idea for biological treatment of refractory wastewater.

功能菌剂的混合发酵研究

随着化工行业的发展，大量有毒有害难降解有机物随工业废水的排放进入环境，这些物质能够在环境中长期存在、积累和扩散，通过食物链对动植物的生存及人类的健康造成不良影响。本文以苯酚、对氯硝基苯、氯苯和十六烷为模拟污染物，以前期研制的功能菌剂为对象，经过紫外线线诱变筛选出优于出发菌株的功能菌，对诱变后功能菌的理化性能进行了研究，对菌种进行了鉴定，在此基础上，就其相互之间的微生态关系进行研究，为混合发酵提供理论基础，并就其最佳发酵条件及发酵参数进行了研究，最后对发酵产品的性能进行了检测。目前，国内外有关功能菌剂的研究还存在多方面的不足，主要包括：①由于多菌种混合发酵过程较为复杂，各菌之间存在复杂的相互作用，影响因素较多，关于菌种之间的相互关系研究得很少，环境功能菌剂的发酵方法大多采用单独发酵后混合的方式。单独发酵对原材料、设备和能源的利用率较低，对于多菌种制剂发酵，在设备、能源和原材料的方面造成的浪费更大，将会大幅增加菌剂的生产成本，影响多菌种功能菌剂的发展；②功能菌剂生产过程的质量控制方面研究得较少；③功能菌剂产品的稳定性、抗冲击性能研究得较少，对环境微生物制剂的研究主要集中在菌种选育和培养条件优化方面。 通过本论文研究，得到以下主要结论。 （1）在紫外线诱变处理中，用紫外线对发生一定程度退化的出发菌株进行诱变处理后，六株具有高效降解性能的菌株被筛选出来，诱变筛选出的菌株形态和ERIC-PCR指纹图谱与出发菌株相比发生了明显改变；而且诱变后的菌株对目标难降解底物的降解能力均得到改善，其中，FPN、FCB、F14、FEm对目标底物的降解率提高了20%以上；诱变后菌株经过7次连续传代接种后，对目标难降解底物的降解率无显著变化，具有一定的遗传稳定性。并对诱变后的功能菌进行了初步的鉴定，这6株菌都分别是芽孢杆菌。 （2）对诱变后的功能菌相互之间的微生态关系进行了研究，通过抑菌实验、生长量以及基质消耗量的比较，确定它们之间的生长关系是无害共栖关系，可以进行混合发酵。 （3）对该功能菌剂进行发酵培养条件研究，结果表明发酵培养基的最佳成分（g/L）：葡萄糖 31.0g/L、玉米粉10.0g/L、磷酸氢二钾1.0g/L、硫酸铵1.1g/L、硫酸镁0.55g/L。通过研究不同的培养条件对菌体生长和降解性能的影响，确定了最佳培养条件：培养基初始pH7.5；最适温度32℃；培养基装液量125mL（250 mL三角瓶），以及培养时间对降解性能的影响，培养20 h的产物对降解最为有利。通过研究添加不同目标污染物对菌体生长和降解性能的影响，确定了添加目标污染物的最佳量以及最佳时间：苯酚投加量：1.125 g/L，对氯硝基苯投加量：0.1 g/L；最佳投加时间为发酵培养开始后4 h。 （4）以摇瓶分批发酵最优条件为基础，对FPN、F10、FCB、FNa、F14 和 FEm进行了摇瓶分批发酵试验。以摇瓶分批发酵试验数据为依据，对功能菌剂分批发酵动力学进行了研究，建立了菌体生长和基质消耗的动力学模型，拟合模型能较好的反映功能菌剂分批发酵过程。 （5）功能菌剂和活性污泥协同作用，可以提高系统的生物降解能力，功能菌剂投加量为2%，新鲜活性污泥3500 mg/L，降解24 h条件下，功能菌剂和活性污泥的协同作用对COD的去除率和对照组相比，最多的提高了36.8%。功能菌剂和活性污泥协同作用以及活性污泥的单独作用，其生物降解过程均符合一级反应动力学过程，功能菌剂和活性污泥协同作用的生物降解动力学方程为：，相关系数97%。采用SBR运行方式，引入功能菌剂的SBR系统明显能够改善和提高生物降解的效率。与仅有活性污泥的系统相比，系统对COD的平均去除率可以提高27.1%，同时，系统的耐负荷冲击以及耐毒害冲击的性能比仅有活性污泥的SBR系统强，特别是负荷冲击对引入功能菌剂的SBR系统影响很小。仅有活性污泥的SBR系统经过负荷冲击和毒害冲击之后，不能恢复到冲击之前的水平，而且系统有效作用时间的周期比引入功能菌剂的SBR系统相比大大缩短，而引入功能菌剂的SBR系统处理效果较为稳定，恢复能力很强。 Along with the development of industries, many recalcitrant organic chemicals have been discharged into natural environments together with wastewaters and can exist in waters, soil and sediments for a long time without degradation. These haz-ardous substances, their byporducts and metabolizabilities can be highly toxic, mu-tagenic and carcinogenic, thereby threatening animals, plants and human health through food chain. Consequently the removal of these compounds is of significant interest in the area of wastewater treatment. In this dissertation, the phenol, hydro-quinone, chlorobenzene and hexadecane treated as the model pollutants, the func-tional microorganism agent was used as the starting strains, they treated with ultra-violet light, and then the mutant strains with high degradation ability were screened out and identified primarily, the relationship between these stains were studied, the medium composition and fermentation conditions were optimized, the degradation ability of the fermented production was tested. The literature survey indicates that the study of the microorganism agent is far from complete and more information is re-quired on following problems. 1, Because of the complexity of relationship in mixed fermentation and the complicated factors, the study is hardly to process.2, There is a lack of information on the quality control of the producing process .3, And there is a lack of information on the stability about the microorganism agent. In this dissertation, the main results of the present study could be summarized as follows: (1)The degenerate starting strains were treated with the ultraviolet light, and six mutant strains with high biodegradation ability were screened out by using the me-dium with selective pressure of model pollutants. The mutant strains had great changes in colonialmorphology and ERIC-PCR fingerprinting. And the mutant strains got obvious advantages over the starting strains in degradation ability and over 20% improvement of removal rates was achieved for FPN、FCB、F14 and FEm. The de-gradation ability of the mutant strains was stable after seven generations. After that, the mutant strains were primarily identified as bacillus respectively. (2) The relationship between these mutant strains was studied. By the compari-son of antibiosis effect, biomass and consumption of substrate, the relationships were neutralism and they could be mixed fermented. (3) The optimized cultivation conditions were as follows: glucose 31.0 g/L, corn power 10 g/L, K2HPO4 1.0 g/L, (NH4)2SO4 1.1 g/L, MgSO4 0.55 g/L, initial pH7.5, temperature 32℃, working volume 125 mL/250 mL, and cultivation time 20h (con-sidering the time effect on degradation ability), adding pollutants phenol (1.125 g/L) and hydroquinone (0.1 g/L) into the broth at 4 h after cultivation. (4) Based on the above optimum condition, the batch fermentation was per-formed with strains FPN, F10, FCB, FNa, F14 and FEm in shake flask. The batch fermentation kinetics was studied based on the experimental data. Two kinetic models were constructed which could reflect the regularity of growth and substrate consump-tion in the process of batch fermentation. (5) The co-operation of functional microorganism agent and activated sludge could raise biodegradation of system by adding some microorganism agent and 3500 mg/L fresh activated sludge. Bioaugumentation by the addition of high effective deg-radation culture enhanced the treatment effect of SBR system and the COD removal rate was increased by 20%-36.8%. Its biodegradation matched first-order dynamical reaction equation, and the reaction equation was ln0.2327.391ct=−+. The micro-organism agent had the effect of optimization to activated sludge micro-ecosystem. The SBR system adding 2% microorganism agent, the average COD removal rate of that was increased by 27.1% and stronger anti-shock ability to load and toxicant were achieved (compared with SBR system just adding activated sludge). Especially the load-shock has barely effect to the SBR system adding microorganism agent. After the load and toxicant shock, the SBR system just adding activated sludge couldn’t come back to original level and the activated sludge micro-ecosystem was frustrated. The applying of microorganism agent increased biological activity and system’s re-sistance ability to load shock and toxicant shock.

Remediation of Persistent Organic Pollutants (POPs) in Two Different Soils

Persistent organic pollutants (POPs) are a set of chemicals that are toxic, persist in the environment for long periods of time, and biomagnify as they move up through the food chain. The most widely used method of POP destruction is incineration, which is expensive and could result in undesirable by-products. An alternative bioremediation technology, which is cheaper and environ-mentally friendly, was tested during this experiment. Two different soil types containing high and low organic matter (OM) were spiked with 100 mg/kg each of pyrene and Aroclor 1248 and planted with three different species of grasses. The objective of the study was to determine residue recovery levels (availability) and potential effectiveness of these plant species for the remediation of POPs. The results showed that recovery levels were highly dependent on the soil organic matter content—very low in all treatments with the high OM content soil compared to recoveries in the low OM soil. This indicates that availability, and, hence, biodegradability of the contaminants is dependent on the organic matter content of the soil. Moreover, the degree of availability was also significantly different for the two classes of chemicals. The polyaromatic hydrocarbon (PAH) recovery (availability) was extremely low in the high organic matter content soil compared to that of the polychlorinated biphenyls (PCBs). In both soil types, all of the plant species treatments showed significantly greater PCB biodegradation compared to the unplanted controls. Planting did not have any significant effect on the transformation of the PAHs in both soil types; however, planting with switchgrass was the best remedial option for both soil types contaminated with PCB.

Effect of acetylation on the properties of corn starch

Acetylated corn starches with different degrees of substitution (DS 0.85, DS 1.78, DS 2.89) were synthesized by the reaction of corn starch with acetic anhydride in the presence of acetic acid under varying reaction temperatures. The product was characterized by FTIR spectroscopy, H-1 NMR, X-ray diffraction and contact angle measurement. Acid-base titration and H-1 NMR methods were employed to determine the degree of substitution of product. FTIR spectroscopic analysis showed that the characteristic absorption intensities of esterified starch increased with increase in the degree of substitution, and the characterized peak of hydroxyl group almost disappeared in the spectrum of DS 2.89 acetylated starch. The detailed chemical microstructure of native starch and acetylated starch was confirmed by H-1 NMR, C-13 NMR and C-13-(1) H-1 COSY spectra.

Synthesis of biodegradable and electroactive multiblock polylactide and aniline pentamer copolymer for tissue engineering applications

To obtain one biodegradable and electroactive polymer as the scaffold for tissue engineering, the multiblock copolymer PLAAP was designed and synthesized with the condensation polymerization of hydroxyl-capped poly(L-lactide) (PLA) and carboxyl-capped aniline pentamer (AP). The PLAAP copolymer exhibited excellent electroactivity, solubility, and biodegradability. At the same time, as one scaffold material, PLAAP copolymer possesses certain mechanical properties with the tensile strength of 3 MPa, tensile Young 's modulus of 32 MPa, and breaking elongation rate of 95%.

In vivo mineralization and osteogenesis of nanocomposite scaffold of poly (lactide-co-glycolide) and hydroxyapatite surface-grafted with poly(L-lactide)

Nanocomposite of hydroxyapatite (HAP) surface-grafted with poly(L-lactide) (PLLA) (g-HAP) shows a wide application for bone fixation materials due to its improved interface compatibility, mechanical property and biocompatibility in our previous study. In this paper, a 3-D porous scaffold of g-HAP/poly (lactide-co-glycolide) (PLGA) was fabricated using the solvent casting/particulate leaching method to investigate its applications in bone replacement and tissue engineering. The composite of un-grafted HAP/PLGA and neat PLGA were used as controls. Their in vivo mineralization and osteogenesis were investigated by intramuscular implantation and replacement for repairing radius defects of rabbits. After surface modification, more uniform distribution of g-HAP particles but a lower calcium exposure on the surface of g-HAP/PLGA was observed. Intramuscular implantation study showed that the scaffold of g-HAP/PLGA was more stable than that of PLGA, and exhibited similar mineralization and biodegradability to HAP/PLGA at the 12-20 weeks post-surgery.

Effect of peroxide crosslinking on thermal and mechanical properties of poly(epsilon-caprolactone)

Poly(epsilon-caprolactone) (PCL), a saturated polyester, derived from ring-opening polymerization of epsilon-caprolactone, was chemically crosslinked with various amounts of benzoyl peroxide (BPO) by a two-step method by first evenly dispersing the BPO into the PCL matrix and then crosslinking at elevated temperature. The gel fraction increased with an increase in BPO content. The modified Charlesby-Pinner equation was used to calculate the ratio of chain scission and crosslinking. The results showed that both scission and crosslinking occurred, and that crosslinking predominated over scission. The number-average molecular weight between the crosslinks determined by the rubber elasticity theory using the hot set test showed a decrease with increasing BPO content. The melting temperature and crystallinity decreased with an increase in BPO content, and the crystallization temperature increased after crosslinking. Dynamic mechanical analysis results showed a decrease in the glass transition temperature as a result of chemical crosslinking of PCL. This was explained by the observed reduction in crystallinity and the increase in free volume due to restrictions in chain packing.

Thermal and mechanical properties of poly(epsilon-caprolactone) crosslinked with gamma radiation in the presence of triallyl isocyanurate

Poly(epsilon-caprolactone) was crosslinked by gamma radiation in the presence of triallyl isocyanurate. The influence of gamma-radiation crosslinking on the thermal and mechanical properties of poly(epsilon-caprolactone)/triallyl isocyanurate was investigated. Differential scanning calorimetry analyses showed differences between the first and second scans. Dynamic mechanical analysis showed an increase in the glass-transition temperature as a result of the radiation crosslinking of poly(epsilon-caprolactone). Thermogravimetric analysis showed that gamma-radiation crosslinking slightly improved the thermal stability of poly(epsilon-caprolactone). The 7 radiation also strongly influenced the mechanical properties. At room temperature, crosslinking by radiation did not have a significant influence on the Young's modulus and yield stress of poly(E-caprolactone). However, the tensile strength at break and the elongation at break generally decreased with an increase in the crosslinking level. When the temperature was increased above the melting point, the tensile strength at break, elongation at break, and Young's modulus of poly(epsilon-caprolactone) were also reduced with an increase in the crosslinking level. The yield stress disappeared as a result of the disappearance of the crystallites.