Large-area silver-coated silicon nanowire arrays for molecular sensing using surface-enhanced Raman spectroscopy

A new and facile method to prepare large-area silver-coated silicon nanowire arrays for surface-enhanced Raman spectroscopy (SERS)-based sensing is introduced. High-quality silicon nanowire arrays are prepared by a chemical etching method and used as a template for the generation of SERS-active silver-coated silicon nanowire arrays. The morphologies of the silicon nanowire arrays and the type of silver-plating solution are two key factors determining the magnitude of SERS signal enhancement and the sensitivity of detection; they are investigated in detail for the purpose of optimization.

Factors affecting pore structure and performance of poly(vinylidene fluoride-co-hexafluoro propylene) asymmetric porous membrane

Preparation of poly(vinylidene fluoride-co-hexafluoro propylene) (F2.6) flat-sheet asymmetric porous membrane has been studied for the first time. Factors affecting F2.6 membrane pore structure and permeate performance, such as macromolecule pore formers (polyethylene glycol-400, 1000, 1540, 2000 and 6000), the small molecule former (glycerol), swelling agent (trimethyl phosphate) in casting solution, precipitating bath component and temperature, exposure time and ambient humidity, were investigated in detail. Average pore radius and porosity were used to characterize F2.6 membrane structure, and respectively, determined by ultrafiltration and gravimetric method for the wet membrane. Morphology of the resultant membranes was observed by scanning electronic microscopy (SEM). Final test on permeate performance of F2.6 porous membrane was carried out by a direct contact membrane distillation (DCMD) setup. The experimental F2.6 membrane exhibits a higher distilled flux than PVDF membrane under the same operational situations. The determination of contact angle to distilled water also reveals higher hydrophobic nature than that of PVDF membrane.

水热条件下钾长石碱性分解反应机理的实验研究

It is well known that our country is short of water-soluble potassium, but rich in insoluble potassium ores. Based on the work of the formers, using the orthogonal and monofactor experiments, the author optimized the production technology of micro-porous potassium silicon calcium mineral fertilizer by non-stirring hydrothermal chemical reaction when the alkaline earth booster CaO was available. The influences of temperature、time、reactant ratio and water-solid ratio on the dissolution rate of production’s elements were studied by orthogonal experiments, and the production technology was further optimized by monofactor experiments. By XRD、SEM、EDS and dissolving experiments, it was systematically studied that the effects of the reactant ratio、reaction time and reaction temperature on the properties of the production obtained by the hydrothermal reaction between KAlSi3O8 and CaO. The results showed that：when changing of the reaction condition, the reaction productions included tobermorite、 hibschite、α-C2SH and K2Ca(CO3)2; among which, K2Ca(CO3)2 was not the first production containing potassium, but K2Ca(CO3)2 was synthesized by the reaction among KOH、Ca(OH)2 and CO2. Whether the phase was synthesized was related to not only the reaction condition, but also their physicochemical properties; when the reaction condition was changed, the changes of different phases were different. The results of XRD and dissolution rate experiments explained the dissolution characteristic of every element of hydrothermal productions very well, and the relation between the dissolution rate of element and the phase of productions poured a good illumination on the production technology. The results of SEM and EDS showed that: hydrogarnet looked like spherical, and its surface was covered by some productions including K phase and Ca、Si phase; but the morphology of tobermorite was platy or lamellar or needlelike, and parts of Si in the structure of tobermorite were substituted by Al，and some K+ cations were inserted into the Ca interlayer of tobermorite at the same time. It was the first time that the interface between KAlSi3O8 and Ca(OH)2 was observed directly by SEM and EDS after the hydrothermal reaction, and the mechanism of hydrothermal reaction of KAlSi3O8 and Ca(OH)2 was further discussed. These results indicated that: the Ca-KAlSi3O8 intermediate compound was formed at first, and some K was released into the solution and KOH was produced at the same time; the C-S-H phase appeared before hydrogarnet, and then hydrogarnet was synthesized when the chemical reaction was carried on; if the reaction was carried on furthermore, α-C2SH、tobermorite and other C-S-H phases of different atom ratio appeared. The author found that the structure of KAlSi3O8 would be more drastically destroyed if there were some reactants, such as Ca(OH)2 which reacted with KAlSi3O8 and new phases were formed after the hydrothermal reaction between KAlSi3O8 and alkaline solution of equal ionic strength was finished. With the combination of calcination and hydrothermal reaction methods, the dissolution rate of products were greatly improved when the hydrothermal reaction was carried out after KAlSi3O8 and CaCO3 were calcined. Furthermore, the author has tentatively explored how to evaluate the effects of the differences of the activity of lime on the dissolution properties of hydrothermal products.

Euro-Commentary : Scenario Analysis and Regional Economic Development: The Case of Mid Wales

Fuller-Love, Nerys, et al., 'Euro-Commentary : Scenario Analysis and Regional Economic Development: The Case of Mid Wales', European Urban and Regional Studies (2006) 13(2) pp.143-149 RAE2008

Inorganic glasses, glass-forming liquids and amorphizing solids

Greaves, George; Sen, S., (2007) 'Inorganic glasses, glass-forming liquids and amorphizing solids', Advances in Physics 56(1) pp.1-166 RAE2008

Nihilism and emptiness: Nishitani's encounter with Nietzsche

In this thesis, I examine the relationship between the Kyoto School philosopher, Nishitani Keiji, and the work of Friedrich Nietzsche, focusing on the two thinkers’ respective approaches to the problem of nihilism. The work begins by positioning Nishitani’s interpretation of Nietzsche’s account of nihilism with reference to diverse readings of Nietzsche in Western scholarship. I then consider the development of Nishitani’s reading of Nietzsche from his lecture series on nihilism, The Self- Overcoming of Nihilism, through to his magnum opus, Religion and Nothingness. I make two key contributions to recent scholarly debate on Nishitani’s relationship to Nietzsche. The first is to emphasise the importance of Nishitani’s response to the idea of eternal recurrence for understanding his critical approach to Nietzsche’s thinking. I argue against the view, offered by Bret Davis, that Nishitani’s criticisms of Nietzsche are primarily based on the former’s negative assessment of the idea of will to power. The second contribution is to situate Nishitani’s critical approach to eternal recurrence within his broader attempt to formulate a Zen-influenced conception of temporality and historicity. I then argue for the necessity of this conceptual background for coming to grips with his conception of the ‘transhistorical’ grounds of historicity in emptiness (śūnyatā), as outlined in the later chapters of Religion and Nothingness.

Novel co-crystals of the nutraceutical sinapic acid

Sinapic acid (SA) is a nutraceutical with known anti-oxidant, anti-microbial, anti-inflammatory, anti-cancer, and anti-anxiety properties. Novel co-crystals of SA were prepared with co-formers belonging to the category of GRAS [isonicotinic acid (INC), nicotinamide (NIA)], non-GRAS [4-pyridinecarbonitrile (PYC)], and active pharmaceutical ingredients (APIs) [6-propyl-2-thiouracil (PTU)] list of compounds. Structural study based on the X-ray crystal structures revealed the intermolecular hydrogen-bonded interactions and molecular packing. The crystal structure of sinapic acid shows the anticipated acid-acid homodimer along with discrete hydrogen bonds between the acid carbonyl and the phenolic moiety. The robust acid-acid homodimer appears to be very stable and is retained in the structures of two co-crystals (SA[middle dot]NIA and SA[middle dot]PYC). In these cases, co-crystallization occurs via intermolecular phenol O-H[three dots, centered]Naromatic hydrogen bonds between the co-formers. In the SA[middle dot]PTU[middle dot]2MeCN co-crystal the acid-acid homodimer gives way to the anticipated acid-amide heterodimer, with the phenolic moiety of SA hydrogen-bonded to acetonitrile. Attempts at obtaining the desolvated co-crystal led to lattice breakdown, thus highlighting the importance of acetonitrile in the formation of the co-crystal. Among the co-crystals examined, SA[middle dot]INC (5 weeks), SA[middle dot]NIA (8 weeks) and SA[middle dot]PYC (5 weeks) were found to be stable under accelerated humidity conditions (40 [degree]C, 75% RH), whereas SA[middle dot]PTU[middle dot]2MeCN decomposed after one week into individual components due to solvent loss.

Tony Mann writes

Within the "Notices" section of BSHM Bulletin 6, short item entitled "Tony Mann writes:" giving details of a sixth-formers' "maths taster day".

Physicochemical and drug diffusion analysis of rifampicin containing polyethylene glycol-poly(epsilon-caprolactone) networks designed for medical device applications

This study reports the physicochemical and drug diffusion properties of rifampicin containing poly(epsilon-caprolactone) (PCL)/polyethylene glycol (PEG) networks, designed as bioactive biomaterials. Uniquely, the effects of the states of both rifampicin and PEG and the interplay between these components on these properties are described. PCL matrices containing rifampicin (1-5%, w/w) and PEG 200 (0-15%, w/w) were prepared by casting from an organic solvent (dichloromethane). The films were subsequently characterized in terms of their thermal/thermorheological, surface and tensile properties, biodegradation and drug diffusion/release properties. Incorporation of PEG and/or rifampicin significantly affected the tensile and surface properties of PCL, lowering the ultimate tensile strength, % elongation at break, Young modulus and storage and loss moduli. Both in the absence and presence of PEG, solubilisation of rifampicin within the crystalline domains of PCL was observed. PEG was present as a dispersed liquid phase. The release of rifampicin (3% loading) was unaffected by the presence of PEG. Similarly the release of rifampicin (5%) was unaffected by low concentrations of PEG (5-10%) however, at higher loadings, the release rate of rifampicin was enhanced by the presence of PEG. Rifampicin release (10% loading) was enhanced by the presence of PEG in a concentration dependent fashion. These observations were accredited to enhanced porosity of the matrix. In all cases, diffusion-controlled release of rifampicin occurred which was unaffected by polymer degradation. This study has uniquely illustrated the effect of hydrophilic pore formers on the physicochemical properties of PCL. Interestingly, enhanced diffusion controlled release was only observed from biomaterials containing high loadings of PEG and rifampicin (5, 10%), concentrations that were shown to affect the mechanical properties of the biomaterials. Care should therefore be shown when adopting this strategy to enhance release of bioactive agents from biomaterials. (C) 2011 Elsevier B.V. All rights reserved.

Polemic and apocalyptic in the Cromwellian invasion of Scotland

This article describes the culture of print and polemic associated with the Cromwellian invasion of Scotland and the resistance of the Church of Scotland. It argues that print solidified Parliamentary ideas during the invasion but that it did not continue to do so after English dominance had been established. These texts illustrate the divisions between the mentalité of the Cromwellian rank-and-file and that of the rather small and probably unrepresentative body of opinion formers who sought to control and represent it.

The rise of the digital citizen-stakeholder: rebalancing multistakeholder governance

The principle feature in the evolution of the internet has been its ever growing reach to include old and young, rich and poor. The internet’s ever encroaching presence has transported it from our desktop to our pocket and into our glasses. This is illustrated in the Internet Society Questionnaire on Multistakeholder Governance, which found the main factors affecting change in the Internet governance landscape were more users online from more countries and the influence of the internet over daily life. The omnipresence of the internet is self- perpetuating; its usefulness grows with every new user and every new piece of data uploaded. The advent of social media and the creation of a virtual presence for each of us, even when we are not physically present or ‘logged on’, means we are fast approaching the point where we are all connected, to everyone else, all the time. We have moved far beyond the point where governments can claim to represent our views which evolve constantly rather than being measured in electoral cycles.
The shift, which has seen citizens as creators of content rather than consumers of it, has undermined the centralist view of democracy and created an environment of wiki democracy or crowd sourced democracy. This is at the heart of what is generally known as Web 2.0, and widely considered to be a positive, democratising force. However, we argue, there are worrying elements here too. Government does not always deliver on the promise of the networked society as it involves citizens and others in the process of government. Also a number of key internet companies have emerged as powerful intermediaries harnessing the efforts of the many, and re- using and re-selling the products and data of content providers in the Web 2.0 environment. A discourse about openness and transparency has been offered as a democratising rationale but much of this masks an uneven relationship where the value of online activity flows not to the creators of content but to those who own the channels of communication and the metadata that they produce.
In this context the state is just one stakeholder in the mix of influencers and opinion formers impacting on our behaviours, and indeed our ideas of what is public. The question of what it means to create or own something, and how all these new relationships to be ordered and governed are subject to fundamental change. While government can often appear slow, unwieldy and even irrelevant in much of this context, there remains a need for some sort of political control to deal with the challenges that technology creates but cannot by itself control. In order for the internet to continue to evolve successfully both technically and socially it is critical that the multistakeholder nature of internet governance be understood and acknowledged, and perhaps to an extent, re- balanced. Stakeholders can no longer be classified in the broad headings of government, private sector and civil society, and their roles seen as some sort of benign and open co-production. Each user of the internet has a stake in its efficacy and each by their presence and participation is contributing to the experience, positive or negative of other users as well as to the commercial success or otherwise of various online service providers. However stakeholders have neither an equal role nor an equal share. The unequal relationship between the providers of content and those who simple package up and transmit that content - while harvesting the valuable data thus produced - needs to be addressed. Arguably this suggests a role for government that involves it moving beyond simply celebrating and facilitating the on- going technological revolution. This paper reviews the shifting landscape of stakeholders and their contribution to the efficacy of the internet. It will look to critically evaluate the primacy of the individual as the key stakeholder and their supposed developing empowerment within the ever growing sea of data. It also looks at the role of individuals in wider governance roles. Governments in a number of jurisdictions have sought to engage, consult or empower citizens through technology but in general these attempts have had little appeal. Citizens have been too busy engaging, consulting and empowering each other to pay much attention to what their governments are up to. George Orwell’s view of the future has not come to pass; in fact the internet has insured the opposite scenario has come to pass. There is no big brother but we are all looking over each other’s shoulder all the time, while at the same time a number of big corporations are capturing and selling all this collective endeavour back to us.

Italian Canzone d'autore and Greek Entechno tragoudi: a comparative overview

‘Canzone d’autore’ is the name that a vast community of Italian music critics, authors, per-formers, producers agreed upon in the mid-1970s, to describe the Italian singer-songwriter genre. Singer-songwriters, who had been missing from Italian popular music – with very few exceptions – until the late 1950s, had become increasingly popular after 1958, and were dubbed ‘cantautori’ in 1960. The term, which propagated to Spain, Catalonia, and Latin Amer-ica, is still in use, but ‘canzone d’autore’ superseded it as a genre label, highlighting the con-nections between authorship and artistic value, implied in the already established notion of ‘Cinéma d’auteur’ from which it was derived.

The expression ‘entechno laiko tragoudi’ (‘art-folk song’) was coined in Greece by Mikis The-odorakis in the 1950s, to describe a new music genre combining the urban-folk musical idi-om with lyrics coming from high-art poetry. Although the origins of the genre are tied to the work of composers like Theodorakis and Hatzidakis who did not perform as singers, from the 1970s onwards entechno became the privileged field of new generations of Greek singer-songwriters. Dropping ‘laiko’ (folk) from its label, entechno expanded its musical influences outside the urban-folk repertory and transformed into the more all-encompassing contempo-rary ‘art song’.

Kroppenstedtia pulmonis sp. nov. and Kroppenstedtia sanguinis sp. nov., isolated from human patients

Three human clinical strains (W9323T , X0209T and X0394) isolated from lung biopsy, blood and cerebral spinal fluid, respectively, were characterized using a polyphasic taxonomic approach. Comparative analysis of the 16S rRNA gene sequences showed the three strains belonged to two novel branches within the genus Kroppenstedtia : 16S rRNA gene sequence analysis of W9323T showed closest sequence similarity to Kroppenstedtia eburnea JFMB- ATET (95.3 %), Kroppenstedtia guangzhouensis GD02T (94.7 %) and strain X0209T (94.6 %); sequence analysis of strain X0209T showed closest sequence similarity to K . eburnea JFMB- ATET (96.4 %) and K. guangzhouensis GD02T (96.0 %). Strains X0209T and X0394 were 99.9 % similar to each other by 16S rRNA gene sequence analysis. The DNA- DNA relatedness was 94.6 %, confirming that X0209T and X0394 belong to the same species. Chemotaxonomic data for strains W9323T and X0209T were consistent with those described for the genus Kroppenstedtia : whole- cell peptidoglycan contained LL- diaminopimelic acid; the major cellular fatty acids were iso- C15 and anteiso- C15 ; and the major menaquinone was MK- 7. Different endospore morphology, carbon utilization profiles, and whole cell wall sugar patterns of strains W9323T and X0209T supported by phylogenetic analysis enabled us to conclude that the strains represent two new species within the genus Kroppenstedtia , for which the names Kroppenstedtia pulmonis sp. nov. (type strain W9323T = DSM 45752T = CCUG 68107T) and Kroppenstedtia sanguinis sp. nov. (type strain X0209T = DSM 45749T = CCUG 38657T) are proposed.

Dissecting the function of the SpoIIIJ and YqjG membrane protein insertases during bacterial spore development

Dissertation presented to obtain the Ph.D degree in Biology, Microbial Biology