Rheology of bituminous mastics and mortars containing crumb rubber from tyres: a novel dry-hybrid technology

This report studied the effect of crumb rubber in the asphalt mixture. The mixtures were also having limestone filler as a modifier. Mastic and mortar (mastic-fine aggregate system) mixture having different quantities of crumb rubber and limestone filler modifiers have been tested in order to find the best rutting resistance combination with an acceptable stiffness. The rheological tests on bituminous mastics and mortars have done in the laboratories in Nottingham Transport Engineering Centre (NTEC) and University of Bologna (DICAM). In the second chapter, an extensive literature review about the binders, additives, asphalt mixtures, various modelling and testing methods have been reviewed. In the third chapter, the physical and rheological properties of the binders have been investigated using both traditional devices and DSRs. The forth chapter is dedicated to finding the behaviour of the modified mastics (Binder-modifier system) with different combinations. Five different combinations of crumb rubber and limestone filler mastic tested with various methods using Dynamic Shear Rheometers. In the fifth chapter, in order to find the effect of the modifiers in the rheological properties of the complete asphalt mixture, the fine aggregates added to the same mastic combinations. In this phase, the behaviour of the system so-called mortar; binder, rubber, filler and fine aggregates) has been studied using the DSR device and the traditional tests. The results show that using fine crumb rubber reduces the thermo sensibility of the mastic (Binder Bitumen System) and improves its elasticity. Limestone filler in the other hand increases the mixture stiffness at high Frequencies. Another important outcome of this research was that the rheological properties of the mortars were following the same trend of the mastics, therefore study the rheological properties of the mastic gives an upright estimation of the mortar.

General Aggregate Source Information, 1979

Only those aggregate sources which have been sampled or tested within the last ten years are listed. This listing additionally ranks sources in accordance with a skid resistance classification as defined herein for aggregates used in asphalt construction. The rankings are based on the ledges used in the past for asphalt aggregates. Upon request, new sources or different combinations of beds within an existing source will be evaluated as to their skid resistance classification. This ranking refers only to the skid resistant properties and does not waive the normal quality requirements for the particular type of aggregate indicated in the contract documents.

Stability of Granular Base Course Materials Containing Bituminous Admixtures

This report concerns the stabilization of three crushed limestones by an ss-1 asphalt emulsion and an asphalt cement, 120-150 penetration. Stabilization is evaluated by marshall stability and triaxial shear tests. Test specimens were compacted by the marshall, standard proctor and vibratory methods. Stabilization is evaluated primarily by triaxial shear tests in which confining pressures of 0 to 80 psi were used. Data were obtained on the angle of internal friction, cohesion, volume change, pore water pressure and strain characteristics of the treated and untreated aggregates. The MOHR envelope, bureau of reclamation and modified stress path methods were used to determine shear strength parameters at failure. Several significant conclusions developed by the authors are as follows: (1) the values for effective angle of internal friction and effective cohesion were substantially independent of asphalt content, (2) straight line MOHR envelopes of failure were observed for all treated stones, (3) bituminous admixtures did little to improve volume change (deformation due to load) characteristics of the three crushed limestones, (4) with respect to pore water characteristics (pore pressures and suctions due to lateral loading), bituminous treatment notably improved only the bedford stone, and (5) at low lateral pressures bituminous treatments increased stability by limiting axial strain. This would reduce rutting of highway bases. At high lateral pressures treated stone was less stable than untreated stone.

Frost Boils, 1961

Paper on frost boils presented at the 6th Annual Asphalt Paving Conference.

Validation of Gyratory Mix Design in Iowa, TR-667, 2016

The design number of gyrations (Ndesign) introduced by the Strategic Highway Research Program (SHRP) and used in the Superior Performing Asphalt Pavement (Superpave) mix design method has been commonly used in flexible pavement design throughout the US since 1996. Ndesign, also known as the compaction effort, is used to simulate field compaction during construction and has been reported to produce air voids that are unable to reach ultimate pavement density within the initial 2 to 3 years post-construction, potentially having an adverse impact on long-term performance. Other state transportation agencies have conducted studies validating the Ndesign for their specific regions, which resulted in modifications of the gyration effort for the various traffic levels. Validating this relationship for Iowa asphalt mix designs will lead to better correlations between mix design target voids, field voids, and performance. A comprehensive analysis of current Ndesign levels investigated the current levels with existing mixes and pavements and developed initial asphalt mix design recommendations that identify an optimum Ndesign through the use of performance data tests.

Effet des charges sur les chaussées en période de restriction des charges - volet terrain

Dans un contexte climatique rigoureux comme celui du Québec, l’interaction entre la charge et le climat a une grande influence sur la performance des structures de chaussées flexibles (Doré et Zubeck, 2009). Pendant le dégel printanier, avec la fonte de la glace, la chaussée s’affaiblit et cet affaiblissement la rend vulnérable à la sollicitation par le trafic lourd ce qui accélère divers phénomènes de dégradation, notamment l’endommagement par fatigue et l’orniérage structural (Farcette, 2010). Afin de minimiser les effets des charges lourdes sur une chaussée affaiblie lors du printemps, les administrations routières choisissent souvent de limiter les charges par essieu ou par véhicule lors du dégel. L’objectif de ce projet est de développer un outil d’aide pour la gestion des restrictions de charge en période de dégel en fonction des données recueillies par les stations de météo routière. Deux sections expérimentales composées des mêmes matériaux mais avec des épaisseurs d’enrobés bitumineux différentes situées au Site Expérimental Routier de l’Université Laval (SERUL) ont été utilisées pour ce projet. Pour bien interpréter le comportement des structures, des jauges de déformations verticales et horizontales, des jauges de contraintes, des jauges de teneur en eau et des thermistances ont été installées dans chaque couche. Pour solliciter mécaniquement la chaussée, un déflectomètre à masse tombante (FWD) a été utilisé. Les résultats obtenus ont permis de de bien comprendre les mécanismes d’affaiblissement de la chaussée durant la période de dégel. Ils ont aussi montré que l’application d’une période de restriction de charge pendant la période de dégel permettait d’avoir un gain sur la durée de vie de la chaussée, cette période de restriction est donc justifiée et efficace. Néanmoins, pour une meilleure gestion du réseau routier, de nouveaux critères pour mieux déterminer la période de restriction de charges sont proposés.

Análise energética em central fixa de produção de massas asfálticas

O consumo energético nas indústrias é algo que tem de ser monitorizado, avaliado e orientado, visando a eficiência energética e sustentabilidade, de modo não só a reduzir o consumo de combustíveis fósseis, mas também a auxiliar a redução da fatura económica. O presente trabalho teve como principal objetivo uma análise energética, e incorpora a caracterização térmica dos materiais utilizados na indústria de produção de massas asfálticas, e o desenvolvimento de um modelo térmico que preveja o comportamento dos mesmos, na produção de massas asfálticas, em central fixa com incorporação de material reciclado a frio. Primariamente o estudo passou pela análise dos consumos energéticos da instalação, caracterizando-a segundo o Decretolei 71/2008, de 15 de Abril, tendo-se constatado, que o consumo de gás natural se evidencia como uma das principais fontes de energia e um dos principais responsáveis pela emissão de GEE (Gases de Efeito de Estufa). Posteriormente o consumo de gás natural foi distribuído pelos pontos consumidores, o cilindro exsicador e a caldeira de aquecimento de óleo térmico. O cilindro exsicador é o principal consumidor energético, com um consumo próximo de 90% do gás natural total. Seguidamente foi realizada uma caracterização dos materiais utilizados na produção de massas asfálticas segundo o DSC (Differential Scanning Calorimetry). Os materiais analisados foram o reciclado/fresado, o calcário, o pó de calcário, o seixo, a areia e o granito. Os resultados dos materiais secos demonstraram que o material com maior cp (calor específico) foi a areia e o menor o calcário. Nos resultados dos materiais saturados observou-se que o seixo apresenta maior facilidade de remoção de humidade e o reciclado/fresado apresenta menor. Por último, foi realizado um modelo térmico com utilização de um balanço mássico e energético ao processo de secagem e sobreaquecimento dos agregados no cilindro exsicador. Conclui-se que as principais influências no consumo de gás natural, na produção de massas asfálticas com inclusão de material reciclado a frio, são: a necessidade energética de aquecimento em função da temperatura a obter, e a energia necessária para remover o conteúdo em humidade presente nos diversos materiais (fresado e agregados).

Correlação entre as propriedades mecânicas de materiais impermeabilizantes a base de elastômeros de poliuréia e poliuretano com o desempenho do sistema aplicado em lajes estruturais

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, Programa de Pós-graduação em Estruturas e Construção Civil, 2015.

Assessment and Life-Cycle Analysis of Recycled Materials for Sustainable Highway

Recycled materials replacing part of virgin materials in highway applications has shown great benefits to the society and environment. Beneficial use of recycled materials can save landfill places, sparse natural resources, and energy consumed in milling and hauling virgin materials. Low price of recycled materials is favorable to cost-saving in pavement projects. Considering the availability of recycled materials in the State of Maryland (MD), four abundant recycled materials, recycled concrete aggregate (RCA), recycled asphalt pavement (RAP), foundry sand (FS), and dredged materials (DM), were studied. A survey was conducted to collect the information of current usage of the four recycled materials in States’ Department of Transportation (DOTs). Based on literature review, mechanical and environmental properties, recommendations, and suggested test standards were investigated separately for the four recycled materials in different applications. Constrains in using these materials were further studied in order to provide recommendations for the development of related MD specifications. To measure social and environmental benefits from using recycled materials, life-cycle assessment was carried out with life-cycle analysis (LCA) program, PaLATE, and green highway rating system, BEST-in-Highway. The survey results indicated the wide use of RAP and RCA in hot mix asphalt (HMA) and graded aggregate base (GAB) respectively, while FS and DM are less used in field. Environmental concerns are less, but the possibly low quality and some adverse mechanical characteristics may hinder the widely use of these recycled materials. Technical documents and current specifications provided by State DOTs are good references to the usage of these materials in MD. Literature review showed consistent results with the survey. Studies from experimental research or site tests showed satisfactory performance of these materials in highway applications, when the substitution rate, gradation, temperature, moisture, or usage of additives, etc. meet some requirements. The results from LCA revealed significant cost savings in using recycled materials. Energy and water consumption, gas emission, and hazardous waste generation generally showed reductions to some degree. Use of new recycled technologies will contribute to more sustainable highways.

Soft computing based parameter identification in pavements and geomechanical systems

Accurate estimation of road pavement geometry and layer material properties through the use of proper nondestructive testing and sensor technologies is essential for evaluating pavement’s structural condition and determining options for maintenance and rehabilitation. For these purposes, pavement deflection basins produced by the nondestructive Falling Weight Deflectometer (FWD) test data are commonly used. The nondestructive FWD test drops weights on the pavement to simulate traffic loads and measures the created pavement deflection basins. Backcalculation of pavement geometry and layer properties using FWD deflections is a difficult inverse problem, and the solution with conventional mathematical methods is often challenging due to the ill-posed nature of the problem. In this dissertation, a hybrid algorithm was developed to seek robust and fast solutions to this inverse problem. The algorithm is based on soft computing techniques, mainly Artificial Neural Networks (ANNs) and Genetic Algorithms (GAs) as well as the use of numerical analysis techniques to properly simulate the geomechanical system. A widely used pavement layered analysis program ILLI-PAVE was employed in the analyses of flexible pavements of various pavement types; including full-depth asphalt and conventional flexible pavements, were built on either lime stabilized soils or untreated subgrade. Nonlinear properties of the subgrade soil and the base course aggregate as transportation geomaterials were also considered. A computer program, Soft Computing Based System Identifier or SOFTSYS, was developed. In SOFTSYS, ANNs were used as surrogate models to provide faster solutions of the nonlinear finite element program ILLI-PAVE. The deflections obtained from FWD tests in the field were matched with the predictions obtained from the numerical simulations to develop SOFTSYS models. The solution to the inverse problem for multi-layered pavements is computationally hard to achieve and is often not feasible due to field variability and quality of the collected data. The primary difficulty in the analysis arises from the substantial increase in the degree of non-uniqueness of the mapping from the pavement layer parameters to the FWD deflections. The insensitivity of some layer properties lowered SOFTSYS model performances. Still, SOFTSYS models were shown to work effectively with the synthetic data obtained from ILLI-PAVE finite element solutions. In general, SOFTSYS solutions very closely matched the ILLI-PAVE mechanistic pavement analysis results. For SOFTSYS validation, field collected FWD data were successfully used to predict pavement layer thicknesses and layer moduli of in-service flexible pavements. Some of the very promising SOFTSYS results indicated average absolute errors on the order of 2%, 7%, and 4% for the Hot Mix Asphalt (HMA) thickness estimation of full-depth asphalt pavements, full-depth pavements on lime stabilized soils and conventional flexible pavements, respectively. The field validations of SOFTSYS data also produced meaningful results. The thickness data obtained from Ground Penetrating Radar testing matched reasonably well with predictions from SOFTSYS models. The differences observed in the HMA and lime stabilized soil layer thicknesses observed were attributed to deflection data variability from FWD tests. The backcalculated asphalt concrete layer thickness results matched better in the case of full-depth asphalt flexible pavements built on lime stabilized soils compared to conventional flexible pavements. Overall, SOFTSYS was capable of producing reliable thickness estimates despite the variability of field constructed asphalt layer thicknesses.

Evaluación de la exposición al ruido industrial en los trabajadores de una planta de asfalto, en la provincia del Azuay y propuesta de plan de control

El presente trabajo se realizó en una Planta de Hormigón Asfáltico, donde se realizó el estudio del ruido como factor de riesgo bajo las perspectivas de: Salud Ocupacional, Seguridad e Higiene Industrial. Este enfoque holístico, define la influencia que éste riesgo laboral ejerce sobre la pérdida de agudeza auditiva. Se estableció inicialmente el marco teórico y legal vigente sobre el ruido, posteriormente se describió la metodología de estudio, operatividad de variables, y la muestra a estudiar. Luego se procedió a la caracterización de la población y área estudiada, así como las actividades productivas. Dentro de la Higiene Industrial, se monitoreó la exposición del nivel de presión sonora, se realizó el comparativo con el nivel permisible (TWA 8 horas) establecido en el “Reglamento de Seguridad y Salud de los Trabajadores”, D.E. 2393. En términos de Seguridad Industrial, se analizó el equipo de protección personal EPP utilizado, y las variables determinantes. En el ámbito de Salud Ocupacional, se estudió: características personales de trabajadores, patologías relacionadas con sordera, y un cuestionario de exposición al ruido. Finalmente se determinó la existencia de sobreexposición a ruido laboral en la empresa objeto de estudio, mediante el estudio del estado de salud auditiva de los colaboradores se determinó la gran incidencia de personal sano y finalmente se determinó las medidas de control a implementarse enfatizadas a la realidad descubierta en el presente estudio, las que incluyen cambios en equipos y maquinaria, buenas prácticas de trabajo, planes de adiestramiento y capacitación en todo el personal entre otros.

Exploration of Ground Penetrating Radar and Time Domain Reflectometry Methods for the Determination of Pavement Dielectric Constant

Traditionally, densities of newly built roadways are checked by direct sampling (cores) or by nuclear density gauge measurements. For roadway engineers, density of asphalt pavement surfaces is essential to determine pavement quality. Unfortunately, field measurements of density by direct sampling or by nuclear measurement are slow processes. Therefore, I have explored the use of rapidly-deployed ground penetrating radar (GPR) as an alternative means of determining pavement quality. The dielectric constant of pavement surface may be a substructure parameter that correlates with pavement density, and can be used as a proxy when density of asphalt is not known from nuclear or destructive methods. The dielectric constant of the asphalt can be determined using ground penetrating radar (GPR). In order to use GPR for evaluation of road surface quality, the relationship between dielectric constants of asphalt and their densities must be established. Field measurements of GPR were taken at four highway sites in Houghton and Keweenaw Counties, Michigan, where density values were also obtained using nuclear methods in the field. Laboratory studies involved asphalt samples taken from the field sites and samples created in the laboratory. These were tested in various ways, including, density, thickness, and time domain reflectometry (TDR). In the field, GPR data was acquired using a 1000 MHz air-launched unit and a ground-coupled unit at 200 and 500 MHz. The equipment used was owned and operated by the Michigan Department of Transportation (MDOT) and available for this study for a total of four days during summer 2005 and spring 2006. The analysis of the reflected waveforms included “routine” processing for velocity using commercial software and direct evaluation of reflection coefficients to determine a dielectric constant. The dielectric constants computed from velocities do not agree well with those obtained from reflection coefficients. Perhaps due to the limited range of asphalt types studied, no correlation between density and dielectric constant was evident. Laboratory measurements were taken with samples removed from the field and samples created for this study. Samples from the field were studied using TDR, in order to obtain dielectric constant directly, and these correlated well with the estimates made from reflection coefficients. Samples created in the laboratory were measured using 1000 MHz air-launched GPR, and 400 MHz ground-coupled GPR, each under both wet and dry conditions. On the basis of these observations, I conclude that dielectric constant of asphalt can be reliably measured from waveform amplitude analysis of GJPR data, based on the consistent agreement with that obtained in the laboratory using TDR. Because of the uniformity of asphalts studied here, any correlation between dielectric constant and density is not yet apparent.

Effects of truck traffic on top-down fatigue cracking performance of flexible pavements using a new mechanics-based analysis framework

The mechanics-based analysis framework predicts top-down fatigue cracking initiation time in asphalt concrete pavements by utilising fracture mechanics and mixture morphology-based property. To reduce the level of complexity involved, traffic data were characterised and incorporated into the framework using the equivalent single axle load (ESAL) approach. There is a concern that this kind of simplistic traffic characterisation might result in erroneous performance predictions and pavement structural designs. This paper integrates axle load spectra and other traffic characterisation parameters into the mechanics-based analysis framework and studies the impact these traffic characterisation parameters have on predicted fatigue cracking performance. The traffic characterisation inputs studied are traffic growth rate, axle load spectra, lateral wheel wander and volume adjustment factors. For this purpose, a traffic integration approach which incorporates Monte Carlo simulation and representative traffic characterisation inputs was developed. The significance of these traffic characterisation parameters was established by evaluating a number of field pavement sections. It is evident from the results that all the traffic characterisation parameters except truck wheel wander have been observed to have significant influence on predicted top-down fatigue cracking performance.

Plan estrategico en el area de ventas

Esta es una empresa colombiana que hace parte del sector de la metalmecánica, fue creada con capital nacional y fundada en los años 70´s. Paso de ser una pequeña empresa de asesorías técnicas y de producción de pequeños equipos, al desarrollo de una nueva línea de productos que abarcan la fabricación de todos los equipos que tienen que ver con la maquinaria pesada, sin incluir la maquinaria amarilla. A pesar de las diferentes crisis económicas por las que ha pasado Colombia, esta empresa ha logrado sobrevivir. Actualmente los diferentes TLC que se han firmado, han llevado a que los competidores aumenten de forma significativa, esto se vea reflejado en el movimiento de las ventas en el transcurso de los años. Este proyecto busca desarrollar un plan estratégico en el área de ventas de la empresa que le permita volver a captar la cantidad de negocios y clientes que solía tener hace unos años. Esto será basándonos en la elaboración de una estrategia clave, que nos permita prolongar la perdurabilidad de la empresa en el mercado, producto de un respectivo conocimiento detallado del servicio y del producto que ofrece la empresa, seguido de un análisis enfocado tanto en los clientes potenciales de la empresa para saber sus razones de no compra, como en el comportamiento del mercado y la competencia analizando temas de carácter financiero (P&G).