Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

Propagação in vitro de barueiro (Dipteryx alata Vog.)

Savannah is the second biome in biodiversity in Brazil, presenting great vegetation endemism. Dipteryx alata Vog. (Fabaceae), native from this biome, is an economically important species, with an incipient market due to the lack of commercial plantations. This highlights the need to develop and provide the basis for the domestication of this species. Thus, this study determined the best conditions for in vitro establishment, multiplication, elongation and rooting of stem tips of D. alata plantlets grown vitro. Two culture media (MS and WPM) were evaluated in different salt concentrations (25, 50, 75 and 100%) for plantlet establishment. Four concentrations of 6– Benzylaminopurine (BAP) (0, 1, 2, 3 and 4 mg L-1) amended with 0.25 mg L-1 naphthalene-acetic acid (NAA) were studied for multiplication. Simultaneous elongation and rooting were studied with four concentrations of NAA (0, 1, 2, 3 and 4 mg L-1) together with 0.5 mg L-1 IBA. The variables analyzed were: shoot length (CPA), root length (CP), fresh matter (MF), dry matter (MSC), stem diameter (DC) and number of leaves (NF), 120 days after inoculation, with the exception of number of shoots, which was evaluated in the multiplication stage only. The medium MS at the original salt concentration (100%) was effective for the in vitro establishment of E. alata, resulting in greater root length (27.65 cm) and number of leaves per plantlet (26.0). The concentration of 4 mg L-1 BAP was the best one for multiplication; however, greater concentrations can boost multiplication. The effect of NAA and IBA were noticeable on in vitro elongation and rooting, with best CPA (3.14 cm) and CR (15.84 cm). Therefore, it is possible to state that the medium MS increases the success probability of in vitro establishment of stem tips of Dipteryx alata. NAA concentrations below 3 mg L-1 were favorable for in vitro development of the species, with essential characteristics for acclimatization success|.