Synthesis, characterization and formulation of a cathode active material: Copper nitroprusside

Nowadays, rechargeable Li-ion batteries play an important role in portable consumer devices. Formulation of such batteries is improvable by researching new cathodic materials that present higher performances of cyclability and negligible efficiency loss over cycles. Goal of this work was to investigate a new cathodic material, copper nitroprusside, which presents a porous 3D framework. Synthesis was carried out by a low-cost and scalable co-precipitation method. Subsequently, the product was characterized by means of different techniques, such as TGA, XRF, CHN elemental analysis, XRD, Mössbauer spectroscopy and cyclic voltammetry. Electrochemical tests were finally performed both in coin cells and by using in situ cells: on one hand, coin cells allowed different formulations to be easily tested, on the other operando cycling led a deeper insight to insertion process and both chemical and physical changes. Results of several tests highlighted a non-reversible electrochemical behavior of the material and a rapid capacity fading over time. Moreover, operando techniques report that amorphisation occurs during the discharge.

Elettrodeposizione di catalizzatori a base di Rh su schiume e fibre metalliche di FeCrAlloy per la produzione di syngas

The preparation of structured catalysts active in the catalytic partial oxidation of methane to syngas, was performed by electrosynthesis of hydroxides on FeCrAlloy foams and fibers. Rh/Mg/Al hydrotalcite-type compounds were prepared by co-precipitation of metallic cations on the support and successive calcination. Electrochemical reactions have been studied during the electrodeposition by linear sweep voltammetry. The experiments were performed at supports immersed in KNO3, KCl, Mg2+ and Al3+ aqueous solutions, starting by different precursors (nitrate and chlorides salts) and modifying the Mg/A ratio. Rh/Mg/Al hydrotalcite-type compounds were deposited on metal foams by applying a -1.2V vs SCE potential for 2000s with a nitrate solution of 0.06M total metal concentration. Firstly it was studied the effect of Mg on the coating propierties, modifying the Rh/Mg/Al atomic ratio (5/70/25, 5/50/45, 5/25/70 e 5/0/95). Then the effect of the amount of Rh was later investigated in the sample with the largest Mg content (Rh/Mg/Al = 5/70/25 and 2/70/28).The results showed that magnesium allowed obtaining the most homogeneous and well adherent coatings, wherein rhodium was well dispersed. The sample with the Rh/Mg /Al ratio equal to5/70/25 showed the best catalytic performances. Decreasing the Rh content, the properties of the coating were not modified, but the catalytic activity was lower, due to a not enough number of active sites to convert the methane. The work on metal fibers focused on the effect of precursor concentration, keeping constant composition, potential and synthesis time at the values of Rh/Mg/Al =5/70/25, -1.2V vs SCE and 1000s. However fibers geometry did not allow to obtain a high quality coating, even if results were quite promising.

Dielectrophoresis (dep) and electrowetting (ewod) as an anti-fouling process for antibacterial surfaces

Nowadays the medical field is struggling to decrease bacteria biofilm formation which leads to infection. Biomedical devices sterilization has not changed over a long period of time. This results in high costs for hospitals healthcare managements. The objective of this project is to investigate electric field effects and surface energy manipulation as solutions for preventing bacteria biofilm for future devices. Based on electrokinectic environments 2 different methods were tested: feasibility of electric gradient through mediums (DEP) reinforced by numerical simulations; and EWOD by the fabrication of golden interdigitated electrodes on silicon glass substrates, standard ~480 nm Teflon (PTFE) layer and polymeric gasket to contain the bacteria medium. In the first experiment quantitative analysis was carried out to achieve forces required to reject bacteria without considering dielectric environment limitations as bacteria and medium frequency dependence. In the second experiment applied voltages was characterized by droplets contact angle measurements and put to the live bacteria tests. The project resulted on promising results for DEP application due to its wide range of frequency that can be used to make a “general” bacteria rejecting; but in terms of practicality, EWOD probably have higher potential for success but more experiments are needed to verify if can prevent biofilm adhesion besides the Teflon non-adhesive properties (including limitations as Teflon breakthrough, layer sensitivity) at incubation times larger than 24 hours.

Sintesi di nanoparticelle composite con morfologia avanzata mediante condensazione in atmosfera inerte o reattiva

Uno dei concetti chiave dell'impiego della nanotecnologia è quello dell'ingegnerizzazione dei materiali alla nano-scala. Si procede così alla realizzazione di materiali aventi morfologia, struttura e composizione ottimizzate per migliorarne specifiche proprietà in maniera controllata. In questo lavoro sono stati realizzati campioni nanoparticellari a base di magnesio con la tecnica (R-)IGC (Reactive or Inert Gas Condensation) allo scopo di studiare come l'atmosfera nella quale vengono sintetizzati ne influenzi le proprietà morfologiche e strutturali, al fine di poterne controllare la crescita per impieghi specifici. In particolare, si sono voluti analizzare i risultati ottenuti in diverse situazioni: nel caso in cui la sintesi avvenga in un'atmosfera contenente una piccola concentrazione di ossigeno e nel caso della coevaporazione di magnesio e titanio in atmosfera inerte o contenente idrogeno. I campioni sono poi stati analizzati dal punto di vista morfologico, composizionale e strutturale mediante microscopia a scansione elettronica e diffrazione a raggi X. E' stato mostrato che la presenza controllata di ossigeno durante la sintesi permette di realizzare strutture core-shell di dimensione media 40nm e che la co-evaporazione di magnesio e titanio permette la sintesi di nanoparticelle di dimensioni medie anche inferiori ai 12nm. La presenza di idrogeno durante l'evaporazione permette inoltre di crescere nanoparticelle contenenti idruro di titanio senza dover ricorrere ad una idrurazione successiva. Le proprietà termodinamiche e cinetiche di (de)-idrurazione dei campioni sintetizzati sono state misurate utilizzando sia un apparato barometrico Sievert, sia effettuando un'analisi direttamente nel sito di crescita. I campioni realizzati non mostrano una termodinamica significativamente diversa da quella del magnesio bulk, mentre le cinetiche dei processi di assorbimento e desorbimento risultano notevolmente più rapide.