Estudo de campo elétrico em linha de transmissão utilizando o método dos elementos de contorno

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sistema de aterramento com cabo contrapeso representado por linhas de transmissão implementado em Matlab com circuitos em cascatas de PÍ

Pós-graduação em Engenharia Elétrica - FEIS

Modelo analítico para linhas de transmissão de energia elétrica: aplicação em linhas trifásicas com plano de simetria vertical

Pós-graduação em Engenharia Elétrica - FEIS

Estudo e desenvolvimento do índice potencial de impacto de descargas atmosféricas em linhas de transmissão

Pós-graduação em Engenharia Mecânica - FEG

epresentação de linhas de transmissão por meio do modelo de bergeron: inclusão do efeito da frequência nos parâmetros longitudinais

Pós-graduação em Engenharia Elétrica - FEIS

Inclusão das representações de gary e de skilling-umoto em modelos de linhas de transmissão trifásicas: Aplicação em simulações de transitórios eletromagnéticos em sistemas de energia elétrica

Pós-graduação em Engenharia Elétrica - FEIS

Representação de linhas de transmissão trifásicas diretamente no domínio das fases por meio da matriz ABCD

Pós-graduação em Engenharia Elétrica - FEIS

Localizador de faltas por ondas viajantes em linhas de transmissão

It is important to ensure smoothly operation of a transmission line, sending energy to the consumption centers with minimal interruptions and safer. With this necessity, the fault location techniques have grown, in order to mitigate the impact of the fault and its correction can be more quickly and accurately. This paper presents a comparison between two different techniques of fault location, the fault location by impedance method, which uses the line parameters, the impedance per distance, voltage and current signals, and the other is the traveling wave method, which uses only a very fast analysis of time, synchronization and length between the line ends, do not using voltage and current values, but the temporal perception of the fault. Using travelling waves fault detection makes the previous knowledge of line parameters obsolete, which helps a lot network technicians and engineers with a quick and easy analysis. The methods are simulated in ATP Draw software, so both algorithms can be evaluated for their effectively and accuracy

Análise de transitórios eletromagnéticos utilizando matrizes de transformação reais-sistemas trifásicos com a presença de cabos pára-raios

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Localização de faltas em alimentadores de distribuição de energia elétrica usando medições esparsas de tensões

Pós-graduação em Engenharia Elétrica - FEIS

Uso do ATP para simulações de descargas atmosféricas em para-raios de 15 kV dos serviços auxiliares de subestações de energia elétrica

This paper addresses the topics required for the selection of surge arresters used, the output of autotransformers, which protect the system Auxiliary Services (SE) of an electrical substation. Surge arresters used are part of the Protection System Lightning (SPDA). Transmission lines mostly run through regions with orographic well diversified and have constant weather changes, which lead to many undesirable interactions with electromagnetic phenomena, such as giving rise to blackout on 10 November 2009, which left nine states without power, which led to unplanned shutdowns in the system that left millions of people without electricity. This work of completion is to determine whether the method used in the selection of surge arresters meet the protection needs faced by a substation auxiliary services, through the use of software use ATPDraw

Estudo da variação do limite de resistência à tração ao longo da bobina de vergalhão de alumínio 1350 AA

Therebar of aluminum 1350 AA produced by CBA are used inthe manufacture of wires and cables for electric power transmission, which marketshows increasingly favorableto aluminum due to itslow densityand high electrical conductivity, but to ensure that this materialmeets all specifications of projectsfor electricity transmission, it must have homogeneity in the chemicaland mechanicalproperties.One of the points of improvement in the process of rod production isreducing the high variation of the limitof tensile strengthalong the coils, therefore, this work seeks a better understanding of the factors that significantly influence the mechanical properties of rebar, specifically assessing the influence oftemperatureat the output of the coils, which can cause a recovery effect on the material andif thereare relevantdifferences between the two modes of rebar production: auto and manual.Samples of six coils have been specifically produced forthis study, which weresubsequently subjected to different annealing temperatures for one hour and ten minutes, similar to what occurs in the output of the coil from the machine. The tensile tests showed that aluminum 1350 AA is significantly influenced by temperature, whose behavior was very similar to that presented in the literature. It was found that the phenomenon of recovery occurred more significantly at high temperatures. Through the optical electron microscope Zeiss, 18 surface maps were made with 100x magnification for each sample in different conditions and the images were analyzed using entropy and fractal dimension, aiming to relate the condition of surface hardening on mechanical property of the samples in that condition. The results showed that these methods can be applied, provided they do not have any kind of imperfection on the surface, once they can influence the results. The study concluded that a more efficient cooling is required in ... (Complete abstract click electronic access below)

A influência da temperatura nas impedâncias de sequência de condutores utilizados na rede primária de distribuição

Distribution networks are formed by long lines that carry electricity substations to homes and industries. These lines have associated impedance and depending on operating conditions of the network these impedances may vary. This paper provides a detailed analysis of the effects observed in studies of voltage drop, short circuit and electrical losses, when considered the drivers sequence impedances used in primary distribution network at different temperatures. Therefore, it is initially presented a calculation methodology and details the factors that influence the final values. The methodology presented tackles in a practical way the main factors that directly or indirectly influence the values of the impedances as an emblematic example and will be properly dealt with throughout the paper is the effect of temperature on the values of the sequence impedances. More specifically is dealt with the case of XLPE cables protected, by having a higher maximum operating temperature than the operating temperature of the network. The effects observed in the power flow generated when considering the impedance values at both temperatures were analyzed. The impedance drivers tend to increase with increasing temperature. Thus the impedance of the conductor XLPE protected will tend to be greater for the maximum operating temperature for which the operating temperature of the network, resulting in greater voltage drop and higher electrical losses

Distribuição da carga hidráulica em linhas de derivação otimizadas por programação linear

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)