Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Desenvolvimento de uma ferramenta computacional para aplicação em métodos de elevação por bombeio centrífugo submerso

The Electrical Submersible Pump (ESP) has been one of the most appropriate solutions for lifting method in onshore and offshore applications. The typical features for this application are adverse temperature, viscosity fluids and gas environments. The difficulties in equipments maintenance and setup contributing to increasing costs of oil production in deep water, therefore, the optimization through automation can be a excellent approach for decrease costs and failures in subsurface equipment. This work describe a computer simulation related with the artificial lifting method ESP. This tool support the dynamic behavior of ESP approach, considering the source and electric energy transmission model for the motor, the electric motor model (including the thermal calculation), flow tubbing simulation, centrifugal pump behavior simulation with liquid nature effects and reservoir requirements. In addition, there are tri-dimensional animation for each ESP subsytem (transformer, motor, pump, seal, gas separator, command unit). This computer simulation propose a improvement for monitoring oil wells for maximization of well production. Currenty, the proprietaries simulators are based on specific equipments manufactures. Therefore, it is not possible simulation equipments of another manufactures. In the propose approach there are support for diverse kinds of manufactures equipments

AO-OIL: um middleware orientado a aspectos baseado em uma arquitetura de referência

Middleware platforms have been widely used as an underlying infrastructure to the development of distributed applications. They provide distribution and heterogeneity transparency and a set of services that ease the construction of distributed applications. Nowadays, the middlewares accommodate an increasing variety of requirements to satisfy distinct application domains. This broad range of application requirements increases the complexity of the middleware, due to the introduction of many cross-cutting concerns in the architecture, which are not properly modularized by traditional programming techniques, resulting in a tangling and spread of theses concerns in the middleware code. The presence of these cross-cutting concerns limits the middleware scalability and aspect-oriented paradigm has been used successfully to improve the modularity, extensibility and customization capabilities of middleware. This work presents AO-OiL, an aspect-oriented (AO) middleware architecture, based on the AO middleware reference architecture. This middleware follows the philosophy that the middleware functionalities must be driven by the application requirements. AO-OiL consists in an AO refactoring of the OiL (Orb in Lua) middleware in order to separate basic and crosscutting concerns. The proposed architecture was implemented in Lua and RE-AspectLua. To evaluate the refactoring impact in the middleware architecture, this paper presents a comparative analysis of performance between AO-OiL and OiL