Desenvolvimento de um equipamento para avaliação do desempenho de geomantas

O controle sobre os processos erosivos é uma necessidade constatada em vários segmentos da engenharia. A movimentação de terra necessária para a execução de taludes rodoviários, por exemplo, pode resultar em taludes de corte ou aterro vulneráveis à erosão superficial. Dentre as alternativas tecnológicas para controle de erosão a utilização de geossintéticos se apresenta como uma solução potencial. A referida aplicação encontra-se em amplo desenvolvimento em alguns países como, por exemplo, nos EUA. No Brasil, a especificação de geossintéticos para controle de erosão é limitada pela ausência de caracterização desses produtos e de normas nacionais, sendo a única fonte técnica de informação, os catálogos dos fabricantes. Neste contexto, o objetivo deste trabalho é construir um equipamento e desenvolver métodos de ensaio para caracterização e avaliação de geossintéticos utilizados no controle de erosão superficial, com base na ASTM D7101. Além de um simulador de chuvas, o equipamento é composto por uma bancada de testes formada por: rampa de escoamento, mesa de suporte e núcleos de solo. Utilizando a bancada construída, foram realizados ensaios para avaliar o funcionamento do equipamento e o desempenho de uma geomanta na redução da taxa de erosão superficial. Os ensaios foram realizados com intensidades de precipitação de 100 ± 4mm/h e 150 ± 4mm/h, durante 30 minutos, com intervalo de leitura de 5 minutos. Os resultados obtidos nos ensaios sem a presença da geomanta mostraram uma perda de solo acentuada durante as chuvas simuladas, com uma iv tendência de crescimento linear da perda de solo acumulada em função do tempo de ensaio. Nos ensaios realizados com a presença da geomanta observou-se a ação de proteção do geossintético com uma redução da ordem de 90% da perda de solo acumulada para todas as intensidades de chuvas utilizadas

Modelagem de decisão na seleção de equipamento: um estudo usando o processo analítico hierárquico na contratação de sondas de perfuração de poços de petróleo

The main goal of this dissertation is to develop a Multi Criteria Decision Aid Model to be used in Oils and Gas perforation rigs contracts choices. The developed model should permit the utilization of multiples criterions, covering problems that exist with models that mainly use the price of the contracts as its decision criterion. The AHP has been chosen because its large utilization, not only academic, but in many other areas, its simplicity of use and flexibility, and also fill all the requirements necessary to complete the task. The development of the model was conducted by interviews and surveys with one specialist in this specific area, who also acts as the main actor on the decision process. The final model consists in six criterions: Costs, mobility, automation, technical support, how fast the service could be concluded and availability to start the operations. Three rigs were chosen as possible solutions for the problem. The results reached by the utilizations of the model suggests that the utilization of AHP as a decision support system in this kind of situation is possible, allowing a simplifications of the problem, and also it s a useful tool to improve every one involved on the process s knowledge about the problem subject, and its possible solutions

Competição e regulamentação no transporte de passageiros: Um estúdio no transporte rodoviário intermunicipal

The objective of this research is the verification of the competition in the intecity market, after the entrance of new competitors (vans and microbus) regulated and clandestine. For verification of this new view was effected one research of documentary character for the knowledge of the regulation and exploratory character of the system Natal - territory of the Seridó, for thus in making will know this problematic, well as its characteristics, attractivenesses and development of the territory of the Seridó, and its link with the Capital (Natal). Later, through a descriptive exploratory research of the type survey with the passengers to know as these are being taken care and its satisfaction in relation to the regulated companies. With the drivers if focus effected one group, and with the staff of the of sale ticket a research survey, aiming at to know the strategies used for the only company of bus that takes care of the territory of the Seridó, the implantation of these and the consequence of the user. In accordance with the generic tipologia of Porter and its strategies, were perceived that the bus company adopted the strategy of price leadership being competitive, using to advantage its bigger space in the market, already vans and the microbuses with its limited participation bet in a strategy of "differentiation" in its service, effecting faster trips and in the strategy of "approach" we find the not regulated services earn the service to the taste of the user

Algoritmos de otimização para decisões de localização de facilidades e distribuição em sistemas multiníveis de transporte rodoviário de carga

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Controle feedback de nível baseado em sensor de imagem aplicado ao equipamento misturador-decantador à inversão de fases (MDIF®)

The treatment of wastewaters contaminated with oil is of great practical interest and it is fundamental in environmental issues. A relevant process, which has been studied on continuous treatment of contaminated water with oil, is the equipment denominated MDIF® (a mixer-settler based on phase inversion). An important variable during the operation of MDIF® is the water-solvent interface level in the separation section. The control of this level is essential both to avoid the dragging of the solvent during the water removal and improve the extraction efficiency of the oil by the solvent. The measurement of oil-water interface level (in line) is still a hard task. There are few sensors able to measure oil-water interface level in a reliable way. In the case of lab scale systems, there are no interface sensors with compatible dimensions. The objective of this work was to implement a level control system to the organic solvent/water interface level on the equipment MDIF®. The detection of the interface level is based on the acquisition and treatment of images obtained dynamically through a standard camera (webcam). The control strategy was developed to operate in feedback mode, where the level measure obtained by image detection is compared to the desired level and an action is taken on a control valve according to an implemented PID law. A control and data acquisition program was developed in Fortran to accomplish the following tasks: image acquisition; water-solvent interface identification; to perform decisions and send control signals; and to record data in files. Some experimental runs in open-loop were carried out using the MDIF® and random pulse disturbances were applied on the input variable (water outlet flow). The responses of interface level permitted the process identification by transfer models. From these models, the parameters for a PID controller were tuned by direct synthesis and tests in closed-loop were performed. Preliminary results for the feedback loop demonstrated that the sensor and the control strategy developed in this work were suitable for the control of organic solvent-water interface level

Projeto e Operação em Escala Semi-Industrial de um Equipamento para Tratamento de Águas Produzidas na Indústria do Petróleo Utilizando Nova Tecnologia: misturador-decantador à inversão de fases - MDIF

The aim of this work is to use a new technology in the treatment of produced wastewaters from oil industry. An unit for treat produced waters called UTMDIF, was designed, installed and operated in an industrial plant for treatment of effluents from oil industry. This unit operates by means of the method of separation of phase inversion and can become a promising alternative to solve the problem of oil/water separation. This method constitutes the basis of the working of a new design of mixersettler of vertical configuration which occupies small surface area. The last characteristic becomes specially important when there is limitation on the lay-out of the plant, for example, over maritime platforms to explore oil. This equipment in a semi-industrial scale treats produced wastewaters contaminated with oil at low concentrations (ranging from 30 to 150 mg/L) and throughputs of 320 m3/d (47,4 m3 m-2 h-1). Good results were obtained in oil/water separation which leads to the necessary specification to discharge those wastewaters. Besides, the non dependence of the efficiency of separation in spite of the salinity of the medium becomes the equipment an attractive new technology to treat wastewaters containing oil at low concentrations

Do talão de nota fiscal ao cupom fiscal: a implantação do ECF no estado do Rio Grande do Norte e sua repercussão na arrecadação do ICMS

The present paper has aimed the analysis of a real instrument which offers great impact in the ICMS revenue: The Fiscal Voucher Emitting Equipment (ECF). In this sense, the effects of the commercial automation process in Rio Grande do Norte s ICMS revenue between 2000 and 2006 were investigated. Based on this goal, the methodology adopted was characterized as a study of quantitative, exploratory-qualitative nature, through the collecting of secondary data, provided by the State Taxation Bureau (SET). In the absence of a statistic model in the existing literature about the approached theme, we decided for the elaboration of a suitable model, with tables and graphics. As a way to observe the effects of these programs on the revenue, the comparison between the ECF users and non users, in the same period, has proved to be of great importance. We reached the conclusion that even though the growth rates amongst the activities that use the ECF had ascended in tributary revenue in the related years, from 2004 on, with the introduction of TEF, this participation presented a higher growth, which leads us to suppose that the use of this recent instrument provides a significant impact in the State effective revenue. We stand out that the collected amounts could have been even higher, if the level of adhesion to the instrument had not been so low, mainly amongst the minor entrepreneurs, which may mean a rooted defraudation in the system. In short, through the set of data obtained, it is possible to conclude that the ECF and the recent TEF have significantly influenced the ICMS revenue in the entire State all over the period that was analyzed

Henrique Novaes: técnica, território e cidade em uma trajetória profissional: Brasil, primeira metade do século XX

The career of civil engineer Henrique de Novaes, a remarkable figure in the academic, technical and political fields, demonstrates its extensive and relevant work across Brazil in the first half of the twentieth century. It covered from the design of water supply and sewage works, road and rail transport networks, works against drought in the Northeast, hydroelectric and harbor facilities to the urbanization planning and architectural projects, which displays a systematic and multiple production. City and territory conformed to his fields of verification, practical and above all, transformation. The search for understanding of the inclusion of a social actor in this process thus contributes to the specific analysis of the doings of Henrique de Novaes, who graduated at Polytechnic School of Rio de Janeiro in 1906. From a polymorphic activity in different scales, one tries to figure how, through academic education or professional practice, urban history in Brazil can be told or built. The introduction of technological innovations matched the purposes of planning and urban sprawl, as well as met the specifications of regulation and institutionalization of public infrastructure services at the time. The overall plans proposed by the engineer thought of the city as a whole, interconnected to the structural networks. At the same time, the knowledge of a larger physical scale the territory bounces back in the urban in a relationship of reciprocity and completeness. The objective research, therefore, tries to understand the roles played by Henrique de Novaes s works and academic education in the accomplishment of systematic modernization of Brazilian urban space and territory, recovering a little known historical figure by current historiography. It is proposed, as methodological axis, that the study of this professional career configures itself as an essential element for understanding the idea of progress embodied in the technical studies and proposals for improvements and sanitation nationwide in the first half of the twentieth century . The primary sources for the construction of this analysis were technical articles in journals of the period ( Clube de Engenharia , Viação e Revista Brasileira de Engenharia ), and technical reports, government messages, newspaper articles published at the time, autobiographical reports and the engineer s verbal communications with relatives. The work is structured in three chapters: "Biographical traces, academic education and 'technical and political' activities" illustrates the initiation into the technical, public and political environment; Chapter 2, "Technique and territory" outlines his network understanding through sanitation and transport services; Chapter 3 "Technique and City" describes the influence of polytechnics knowledge on the propositions of modernization of cities; Finally, "Final Thoughts: An Evaluation," presents an overview of the affiliations and practice of an engineer in the different scales, and its contribution to the modernization of Brazilian urban and territorial space

Um espaço pioneiro de modernidade educacional: Grupo Escolar Augusto Severo -Natal/RN -1908-13

Cette recherche a pour but d analyser l Ecole Augusto Severo, située dans la ville de Natal dont la construction date de 1907,étant le premier établissement d enseignement primaire à l état du Rio Grande do Norte, pendant le processus de restructuration de l enseignement républicain. On cherche à comprendre la représentation de ce milieu scolaire, comme équipement urbain, dans le processus de modernisation de la ville et comme modèle éducationnel pour l état entre 1908 et 1913. En se servant des études historiographes sur le processus de modernisation de quelques villes brésiliennes et des innovations de l enseignement public primaire au pays, à la fin du dix-neuvième siècle et pendant la première décennie du vingtième siècle, comme source pour mieux saisir le contexte général et spécifique. On reconstitue les aspects économiques, sociaux et politiques déterminants des interventions publiques réalisées dans cette ville par les gouvernements républicains ayant comme obectif la construction d une ville embellie,hygiénique et civilisée. Située au quartier Ribeira, principal scénario de la modernité de Natal, l Ecole Augusto Severo est mise em relief comme symbole de civilité du paysage urbain de l époque pour le citoyen du Rio Grande do Norte. Elle disposait de services d énergie et d un tram électrique. Il y avait devant, un grand lac arborisé et une station ferroviaire. A côté, il y avait le théâtre Carlos Gomes (actuellement Alberto Maranhão). Par suíte de son imposante architecture, raffiné style éclectique,on reflète l idéal républicain des elites locales, avec une conception d espace symbolique et éducative de surveillance et contrôle, caractéristiques de l école graduée républicaine

Análise da estrutura e transporte do zooplâncton no estuário do Rio Caravelas (Bahia-Brasil) através do uso do zooscan

Spatial-temporal dynamics of zooplankton in the Caravelas river estuary (Bahia, Brazil). The survey was conducted in order to describe the zooplankton community of the estuary Caravelas (Bahia, Brazil), to quantify and relate the patterns of horizontal and vertical transport with the type of tide (neap and spring) and tidal phase (flood and ebb). Zooplankton samples were collected with the aid of a suction pump (300L), filtered in plankton nets (300μm) and fixed in saline formalin 4%. Samples were collected at a fixed point (A1), near the mouth of the estuary, with samples taken at neap tides and spring tides during the dry and rainy seasons. Samples were collected for 13 hours, at intervals of 1 hour in 3 depths: surface, middle and bottom. Simultaneous collection of biological, we measured the current velocity, temperature and salinity of the water through CTD. In the laboratory, samples were selected for analysis in estereomicroscope, with 25 groups identified, with Copepoda getting the highest number of species. The 168 samples obtained from temporal samples were subsampled and processed on equipment ZooScan, with the aid of software ZooProcess at the end were generated 458.997 vingnettes. 8 taxa were identified automatically, with 16 classified as a semi-automatic. The group Copepoda, despite the limited taxonomic refinement ZooScan, obtained 2 genera and 1 species identified automatically. Among the seasons dry and wet groups Brachyura (zoea), Chaetognatha, and the Calanoid copepods (others), Temora spp., Oithona spp. and Euterpina acutifrons were those who had higher frequency of occurrence, appearing in more than 70% of the samples. Copepoda group showed the largest percentage of relative abundance in both seasons. There was no seasonal variation of total zooplankton, with an average density of 7826±4219 org.m-3 in the dry season, and 7959±3675 org.m-3 in the rainy season, neither between the types and phases of the tides, but seasonal differences were significant recorded for the main zooplankton groups. Vertical stratification was seen for the major zooplankton groups (Brachyura, Chaetognatha, Calanoida (other), Oithona spp, Temora spp. e Euterpina acutifrons). The scale of this stratification varied with the type (square or tide) and tidal phase (flood or ebb). The instantaneous transport was more influenced by current velocity, with higher values observed in spring tides to the total zooplankton, however, there was a variation of this pattern depending on the zooplankton group. According to the data import and export of total zooplankton, the outflow of organisms of the estuary was higher than the input. The results suggest that the estuary of Caravelas may influence the dynamics of organic matter to the adjacent coast, with possible consequences in National Marine Park of Abrolhos

Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Utilização de matérias primas vegetais para aplicabilidade como inibidores de corrosão

In the search for products that act as corrosion inhibitors and do not cause environmental, impact the use of plant extracts as corrosion inhibitors is becoming a promising alternative. In this work the efficiency of polar extracts (ethanol extracts) obtained from the plants Anacardium occidentale Linn (AO) and Phyllantus amarus Schum. & Thonn (PA) as corrosion inhibitors were evaluated in different concentrations. For that AO and PA extracts were solubilized in the microemulsion systems (SME) containing saponified coconut oil as surfactant (SME -OCS and SME-OCS-1) in saline (NaCl 3,5 %) solution, which was also used as electrolyte. Both SME-OCS and SME-OCS-1 were characterized by surface tension and viscosity methods showing a Newtonian fluid behavior. The SME-OCS and SME-OCS-1 systems satisfactorily solubilized the polar extracts AO and PA with measurements carried out by ultraviolet spectroscopy. The measurements of corrosion inhibition efficiencies were performed by the electrochemical linear polarization resistance (LPR) technique as well as weight loss, on the surface of AISI 1020 carbon steel. The maximum corrosion inhibition efficiencies were determined by extrapolation of Tafel plots, showing the following values: 95,6 % for the system SME-OCS-AO, 98,9 % for the system SME-OCS-AO-1 and 93,4 % for the system SME-OCS-PA

Revestimentos a base de Ta/Al2O3 produzidos por aspersão térmica sobre substrato metálico

Metal substrates were coated by thermal spraying plasma torch, they were positioned at a distance of 4 and 5 cm from the nozzle exit of the plasma jet. The starting materials were used for deposition of tantalum oxide powder and aluminium. These two materials were mixed and ground into high-energy mill, then immersed in the torch for the production of alumina coating infused with particles of tantalum with nano and micrometric size. The spraying equipment used is a plasma torch arc not transferred, which operating in the range of 250 A and 80 V, was able to produce enough heat to ignite aluminothermic between Ta2O5 and aluminum. Upon reaching the plasma jet, the mixing powders react with the heat of the blaze, which provides sufficient energy for melting aluminum particles. This energy is transferred through mechanisms of self-propagating to the oxide, beginning a reduction reaction, which then hits on the surface of the substrate and forms a coating on which a composite is formed by a junction metal - ceramic (Ta +Al2O3). The phases and quantification of each were obtained respectively by X-ray diffraction and the Rietveld method. Morphology by scanning electron microscopy and chemical analysis by energy dispersive spectroscopy EDS. It was also performed measurements of the substrate roughness, Vickers microhardness measurements in sprays and determination of the electron temperature of the plasma jet by optical emission spectroscopy EEO. The results confirmed the expectation generated around the end product of spraying the mixture Ta2O5 + Al, both in the formation of nano-sized particles and in their final form. The electron excitation temperature was consistent with the purpose of work, in addition, the thermodynamic temperature was efficient for the reduction process of Ta2O5. The electron excitation temperature showed values of 3000, 4500 and 8000 K for flows10, 20 and 30 l / min respectively, these values were taken at the nozzle exit of the plasma jet. The thermodynamic temperature around 1200 ° C, was effective in the reduction process of Ta2O5

Simulador radiográfico antropomórfico de mama humana

Mammography is a diagnostic imaging method in which interpretation depends on knowledge of radiological aspects as well as the clinical exam and pathophysiology of breast diseases. In this work a mammography phantom was developed to be used for training in the operation of mammographic x-ray equipment, image quality evaluation, self-examination and clinical examination of palpation. Polyurethane was used for the production of the phantoms for its physical and chemical properties and because it is one of the components normally used in prostheses. According to the range of flexibility of the polyurethane, it was possible to simulate breasts with higher or lower amount of adipose tissue. Pathologies such as areolar necrosis and tissue rejection due to surgery reconstruction after partial mastectomy were also simulated. Calcifications and nodules were simulated using the following materials: polyethylene, poly (methyl methacrylate), polyamide, polyurethane and poly (dimethyl silicone). Among these, polyethylene was able to simulate characteristics of calcification as well as breast nodules. The results from mammographic techniques used in this paper for the evaluation of the phantoms are in agreement with data found in the literature. The image analyses of four phantoms indicated significant similarities with the human skin texture and the female breast parenchyma. It was possible to detect in the radiographic images produced regions of high and low radiographic optical density, which are characteristic of breasts with regions of different amount of adipose tissue. The stiffnesses of breast phantoms were adjusted according to the formulation of the polyurethane which enabled the production of phantoms with distinct radiographic features and texture similar to human female breast parenchyma. Clinical palpation exam of the phantoms developed in this work indicated characteristics similar to human breast in skin texture, areolar region and parenchyma

Construção de um aparato experimental para monitoramento in situ da deposição de filmes finos de titânio por magnetron sputtering

The technique of surface coating using magnetron sputtering is one of the most widely used in the surface engineering, for its versatility in obtaining different films as well as in the micro / nanometric thickness control. Among the various process parameters, those related to the active species of the plasma are of the most fundamental importance in the mechanism and kinetics of deposition. In order to identify the active species of the plasma, parameters such as gas flow, pressure and density of electric power were varied during titanium coating on glass substrate. By flowing argon gas of 10, 20, 30, 40 and 50 sccm (cubic centimeters per minute) for each gas flow a sequential scan of the electric current of 0.10, 0.20, 0.30, 0.40 , 0.50 A. The maximum value of 0.50 A was chosen based both on literature data and on limitations of the equipment. The monitoring of plasma species present during the deposition was carried out in situ by the technique of optical emission spectroscopy (OES) through the spectrometer Ocean Optics USB2000 Series. For this purpose, an apparatus was developed to adapt the OES inside the plasma reactor to stay positioned closest to the target. The radiations emitted by the species were detected by an optical fiber placed behind the glass substrate and their intensities as a function of wavelength were, displayed on a monitor screen. The acquisition time for each condition of the plain parameters was related to the minima of spectral lines intensities due to the film formed on the substrate. The intensities of different emission lines of argon and titanium were then analyzed as a function of time, to determine the active species and estimate the thickness of the deposited films. After the deposition, the coated glasses thin films were characterized by optical transmittance through an infrared laser. It was found that the thickness and deposition rate determined by in situ analysis were consistent with the results obtained by laser transmittance