Effects of the density on compressive properties in cellular aluminum produced by the sintering method

The cellular aluminum materials with relative densities of 0.1"-'0.25 were fabricated by the sintering method and effects of the density on mechanical properties of the cellular aluminum were investigated by compressive tests. The cellular aluminum exhibited a plateau region with a nearly constant flow stress. The stress in the plateau region increased with increasing relative density, on the other hand, the densification strain decreased with increasing relative density. Observation of the deformed cells revealed that the cell walls were bent. Besides, the stress in the plateau region was proportional to 1.9 power of the density. These suggest that plastic collapse is dominated by bending of the cell walls for the cellular aluminum produced by the sintering method.

Nucleation sites for ultrafine ferrite produced by deformation of austenite during single-pass strip rolling

An austenitic Ni-30 wt pct Fe alloy, with a stacking-fault energy and deformation characteristics similar to those of austenitic low-carbon steel at elevated temperatures, has been used to examine the defect substructure within austenite deformed by single-pass strip rolling and to identify those features most likely to provide sites for intragranular nucleation of ultrafine ferrite in steels. Samples of this alloy and a 0.095 wt pct C-1.58Mn-0.22Si-0.27Mo steel have been hot rolled and cooled under similar conditions, and the resulting microstructures were compared using transmission electron microscopy (TEM), electron diffraction, and X-ray diffraction. Following a single rolling pass of ∼40 pct reduction of a 2mm strip at 800 °C, three microstructural zones were identified throughout its thickness. The surface zone (of 0.1 to 0.4 mm in depth) within the steel comprised a uniform microstructure of ultrafine ferrite, while the equivalent zone of a Ni-30Fe alloy contained a network of dislocation cells, with an average diameter of 0.5 to 1.0 µm. The scale and distribution and, thus, nucleation density of the ferrite grains formed in the steel were consistent with the formation of individual ferrite nuclei on cell boundaries within the austenite. In the transition zone, 0.3 to 0.5 mm below the surface of the steel strip, discrete polygonal ferrite grains were observed to form in parallel, and closely spaced “rafts” traversing individual grains of austenite. Based on observations of the equivalent zone of the rolled Ni-30Fe alloy, the ferrite distribution could be correlated with planar defects in the form of intragranular microshear bands formed within the deformed austenite during rolling. Within the central zone of the steel strip, a bainitic microstructure, typical of that observed after conventional hot rolling of this steel, was observed following air cooling. In this region of the rolled Ni-30Fe alloy, a network of microbands was observed, typical of material deformed under plane-strain conditions.

Micro-porous nickel produced by powder metallurgy

Micro-porous nickel (Ni) with an open cell structure was fabricated by a special powder metallurgical process, which includes the adding of a space-holding material. The average pore size of the micro-porous Ni samples approximated 30 μm and 150 μm, and the porosity ranged from 60 % to 80 %. The porous characteristics of the Ni samples were observed using scanning electron microscopy (SEM) and the mechanical properties were evaluated using compressive tests. For comparison, porous Ni samples with a macro-porous structure prepared by both powder metallurgy
(pore size 800 μm) and the traditional chemical vapour deposition (CVD) method (pore size 1300 μm) were also presented. Results indicated that the porous Ni samples with a micro-porous structure exhibited different deformation behaviour and dramatically increased mechanical properties,
compared to those of the macro-porous Ni samples.

Mechanical properties of micro-porous metals produced by space-holding sintering

Micro-porous nickel foams with an open cell structure were fabricated by the space-holding sintering. The average pore size of the micro-porous nickel specimens ranged from 30 μm to 150 μm, and the porosity ranged from 60 % to 80 %. The porous characteristics of the nickel specimens were observed using scanning electron microscopy (SEM). The mechanical properties were studied using compressive tests. For comparison, macro-porous nickel foams prepared by the chemical vapour deposition method with pore sizes of 800 μm and 1300 μm and porosity of 95 % were also presented. Results indicated that the ratio value of 6 and higher for the specimen length to cell size (L/d) is satisfying for obtaining stable compressive properties. The micro-porous nickel specimens exhibited different deformation behaviour and dramatically increased mechanical properties, compared to those of the macro-porous nickel specimens.

Species-specific characteristics and individual variation of the bark call produced by male Australian fur seals (Arctocephalus pusillus doriferus)

Australian fur seals Arctocephalus pusillus doriferus are colonial breeding animals forming dense social groups during the breeding season. During this time, males establish and defend territories through physical conflicts, stereotyped posturing and vocalisations. While vocalisations are suggested to play an important role in male recognition systems, it has received little attention. Recordings of nine adult male Australian fur seals were made during the 2000 and 2001 breeding seasons at Kanowna Island (39° 10’S, 146° 18' E), Bass Strait, Australia. The in-air bark vocalisations of territory-holding males were used to characterise the Bark Call and to determine whether males produce individually distinct calls, which could be used as a basis for vocal recognition. Seventeen frequency and temporal variables were measured from a total of 162 barks from nine individual males. The Bark Series was more reliably classified (83%) to the correct caller compared to the Bark Unit. This was assigned with less certainty (68%), although the classification was still relatively high. Findings from this study indicate that there is sufficient stereotypy within individual calls, and sufficient variation between them, to enable vocal recognition in male Australian fur seals.

Individual variation in the pup attraction call produced by female Australian fur seals during early lactation

Otariid seals (fur seals and sea lions) are colonial breeders with large numbers of females giving birth on land during a synchronous breeding period. Once pups are born, females alternate between feeding their young ashore and foraging at sea. Upon return, both mother and pup must relocate each other and it is thought to be primarily facilitated by vocal recognition. Vocalizations of thirteen female Australian fur seals (Arctocephalus pusillus doriferus) were recorded during the breeding seasons of December 2000 and 2001, when pups are aged from newborns to one month. The pup attraction call was examined to determine whether females produce individually distinct calls which could be used by pups as a basis for vocal recognition. Potential for individual coding, discriminant function analysis (DFA), and classification and regression tree analysis were used to determine which call features were important in separating individuals. Using the results from all three analyses: F0, MIN F and DUR were considered important in separating individuals. In 76% of cases, the PAC was classified to the correct caller, using DFA, suggesting that there is sufficient stereotypy within individual calls, and sufficient variation between them, to enable vocal recognition by pups of this species.

Wellbeing of Australians : work, wealth and happiness : part A

The Australian Unity Wellbeing Index monitors the subjective wellbeing of the Australian population. Our first survey was conducted in April 2001 and this report concerns the 17th survey, undertaken in April 2007. Our previous survey had been conducted six months earlier in October 2006. This intervening period was relatively uneventful in terms of events likely to change population wellbeing. A new leader of the opposition Labor Party was appointed (Kevin Rudd) who seemed more likely than
his predecessors to wrest power from long-serving Prime Minister John Howard (Liberal Party) in an election to be held around the end of 2007.
Each survey involves a telephone interview with a new sample of 2,000 Australians, selected to represent the national population geographic distribution. These surveys comprise the Personal Wellbeing Index, which measures people’s satisfaction with their own lives, and the National
Wellbeing Index, which measures how satisfied people are with life in Australia. Other items include a standard set of demographic questions and other survey-specific questions. The specific topics for Survey 17 are time at work, and anticipated happiness at doubling or halving household income.

Pure boron nitride nanowires produced from boron triiodide

A thick layer of pure boron nitride (BN) nanowires with a uniform diameter of 20 nm was synthesized for the first time using a CVD process with a new precursor of boron triiodide (BI3). Transmission electron microscopy revealed a nanocrystalline structure in the BN nanowires and the absence of any catalyst particle. Some BN nanowires self-assembled into thick threads up to several hundred micrometres long on top of the nanowire layer. The nitriding reactions and lack of catalyst suggest new formation mechanisms of the BN nanowires.

Fine grained AZ31 produced by conventional thermo-mechanical processing

The magnesium alloy AZ31 was processed by severe hot rolling and annealing. This processing was optimised to produce recrystallised grain sizes as small as 2.2 μm. The texture of the processed plate was similar to that of the as-received material, with a strong basal alignment in the normal direction. Tensile testing of the fine grained material showed an increase in the strength and elongation compared to the as-received plate. It is  concluded that the improved mechanical properties of the fine grained material results from a refinement in the grain size and the elimination of shear bands that pre-exist in the as-received material.

Characterisation of Ni–Ti thin films produced by filtered arc deposition

Ti–49.5 at%Ni thin films have been formed by deposition onto Si and glass substrates using a filtered arc deposition system (FADS). The films deposited on glass were composed of nanocrystalline parent phase grains contained within an amorphous matrix. The films deposited onto silicon were crystalline, and were largely parent phase whereas a bulk alloy of the same composition would be expected to be martensite. The stabilisation of the parent phase is proposed to be a grain size effect, with the critical grain size for parent phase stabilisation being about 30 nm.