The influence of fine ferrite formation on the γ/α interface, fine bainite and retained austenite in a thermomechanically-processed transformation induced plasticity steel

An Fe-0.26C-1.96Si-2Mn with 0.31Mo (wt%) steel was subjected to a novel thermomechanical processing route to produce fine ferrite with different volume fractions, bainite, and retained austenite. Two types of fine ferrites were found to be: (i) formed along prior austenite grain boundaries, and (ii) formed intragranularly in the interior of austenite grains. An increase in the volume fraction of fine ferrite led to the preferential formation of blocky retained austenite with low stability, and to a decrease in the volume fraction of bainite with stable layers of retained austenite. The difference in the morphology of the bainitic ferrite and the retained austenite after different isothermal ferrite times was found to be responsible for the deterioration of the mechanical properties. The segregation of Mn, Mo, and C at distances of 2-2.5 nm from the ferrite and retained austenite/martensite interface on the retained austenite/martensite site was observed after 2700 s of isothermal hold. It was suggested that the segregation occurred during the austenite-to-ferrite transformation, and that this would decrease the interface mobility, which affects the austenite-to-ferrite transformation and ferrite grain size.

Influence of ionic liquids on the electrical conductivity and morphology of PEDOT:PSS films

Small-molecule nonvolatile additives based on ionic liquids (IL) as electrical conductivity enhancer in Poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) was studied. Ionic liquids were investigated in the synthesis of self-assembled, highly organized hybrid nanostructures due to their ability as supramolecular solvents. Different percentage of five ionic liquids, such as 1-butyl-3-methylimidazolium tetrafluoroborate (bmim) F 4 and 1-butyl-3-methylimidazolium bromide (bmim)Br were added to a PEDOT:PSScommercial dispersion. Films of pure PEDOT:PSS showed an average conductivity of 14 S cm-1, which corresponded to the value range given by the supplier. AFM images showed that IL induced the formation of a three-dimensional conducting network with smaller PEDOT domains. The ionic character of the films was significantly increased because of the presence of ionic liquids, which can be used effectively in optoelectronic devices.

Research on the influence of yarn parameters on the ultraviolet protection of yarns

Considering both the yarn parameters and the light interaction (reflectance and transmittance) between two adjacent yarns, an optical model was presented to understand the ultraviolet (UV) light penetrating a single undyed yarn and a lot of yarns. The optical model was verified with results of diffuse reflectance spectra measurement on wool yarn samples. This optical model was used to predict the factors influencing UV protection, including fibre diameter, yarn linear density, yarn twist, transmittance index and refractive index. The statistical predictive model was also set up to show the relationship between the yarn parameters and the UV protection (UPF values) of the yarns. Yarns with the fine diameter, large yarn linear density and low yarn twist had the high UV protection.

The Influence of Task Characteristics on the Intermanual Asymmetry of Motor Overflow

The two studies reported here were designed to test the proposition that greater motor overflow occurs when movements are performed by the non-dominant hand. Unlike previous studies using normal adults, the task in these studies did not require force production. In the first study, a group of 19 right-handed participants performed unweighted finger lifting. That the frequency of motor overflow occurrence was the same regardless of which hand performed the task, did not support findings from other studies where tasks involving force production resulted in more overflow when performed by the non-dominant hand. To investigate further the influence of task characteristics on motor overflow occurrence, in the second study participants were required to remember and reproduce a prescribed sequence of four finger lifts. Left- and right-handed participants ( N =30) performed both single and sequenced finger lifting. The relative frequency of motor overflow (unintended lifts of fingers of the passive hand) was compared between hand preference groups, active hand and task type (single/sequenced). Contrary to the expectation that motor overflow would be greater for the sequenced finger lifting task, overflow was exhibited with a significantly greater frequency on single finger lifting. This finding indicates that task characteristics influence the pattern of overflow occurrence in normal adults. The task used in this study did not involve force production and did not result in an intermanual asymmetry of motor overflow. This contrasts with findings from other studies requiring adults to exert forces where greater overflow occurred when the non-dominant hand was active. However, this study confirms previous findings which show that left-handers produce greater overflow compared to right-handers regardless of the task being performed and the hand performing the task.

Possible influence of Gondwanan glaciation on low-latitude carbonate sedimentation and trans-equatorial faunal migration: the lower Permian of South China

Peculiar Early Permian palaeontological and sedimentological features are reviewed from South China, including characteristic Early Permian cold-water Gondwanan brachiopod taxa and faunas from Sichuan and Guizhou provinces, widespread rosettes and irregular aggregates of calcite prisms ('Chrysanthemum Stones') within the Qixia limestones, and lack of significant Early Permian reef buildups. The occurrences of these features are at odds with the currently widely held view that South China was located in a palaeotropical, warm-water setting throughout the Permian and hence harboured a highly diverse shallow marine biota. In this paper, I propose a working hypothesis, suggesting that influence of at least cool water masses may have intermittently occurred in South China during the Early Permian, which facilitated the formation of the cool water-influenced palaeontological and sedimentological features and promoted the interchanges of cool to cold water marine faunas between the Gondwanan and Boreal Realms. These cool water masses may have been transported to low-latitude regions as deep currents from northern and eastern shelves of Gondwanaland and upwelled along the western coast of South China as well as within the relatively deep-water basins of central South China. Prevalence of these meridional, north-directed deep cold water currents during the Early Permian may have been related to the glaciation event of Gondwanaland. An alternative and/or additional source of cooling may have also originated from strong easterly palaeoequatorial boundary currents operating within the Palaeotethys at times during the Early Permian, inducing and/or enhancing upwelling of cool to cold water masses in the eastern Palaeotethys. This latter scenario is analogous to the occasional 'La Nina' effect (opposite to the 'El Nino' effect) at the equatorial belt of the modern Pacific Ocean.

Influence of grain size on the compressive deformation of wrought Mg-3A1-1Zn

The influence of the grain size on the flow stress of extruded Mg–3Al–1Zn tested in compression is examined. Samples with grain sizes varying between 3 and 23 μm were prepared by altering the extrusion conditions. Compression testing of the extruded bar was carried out at temperatures between ambient and 200 °C. Twinning dominated the deformation at lower temperatures but this gave way to slip dominated flow when the temperature was raised. For tests carried out at intermediate temperatures, a similar transition was observed when the grain size was reduced. The transition was accompanied by a change in flow curve shape and Hall–Petch slope. The peak stresses achieved when twinning dominated the deformation were up to 100 MPa greater than those seen when slip dominated the flow. Critical grain sizes marking the twinning–slip transition were identified and these are described in terms of the deformation conditions.

Influence of grain size on hot working stresses and microstructures in Mg-3A1-1Zn

The influence of the grain size on the deformation of Mg–3Al–1Zn was examined in compression at 300 °C. At low strains the flow stress increases with increasing grain size. This is interpreted in terms of dynamic recrystallization. Empirical models of dynamic recrystallization are developed and employed to generate a microstructure map.

Influence of z-pinning on the buckling of composite laminates under edge-wise compression

Z-pinning is a newly developed technique to enhance the strength of composite laminates in the thickness direction. Recent experimental and theoretical studies have shown that z-pins significantly improve mode I and mode II fracture toughness. In practice, buckling accompanying delamination is a typical failure mode in laminated composite structures. For a complete understanding of the z-pinning technique towards improvements of the overall mechanical properties of laminated composites, a numerical model is developed in this paper to investigate the influence of z-pins on the buckling composite laminates with initial delaminations under edge-wise compression. The numerical results indicate that z-pinning can indeed effectively increase the compressive strength of the composite laminates provided that the initial imperfection is within a certain range. The magnitude of the improvement is consistent with available experimental data.

The influence of sodium salts on binary mixtures of bitter-tasting compounds

In order to study potential mixture interactions among bitter compounds, selected sodium salts were added to five compounds presented either alone or as binary bitter- ompound mixtures. Each compound was tested at a concentration that elicited ‘weak’ perceived bitterness. The bitter compounds were mixed at these concentrations to form a subset of possible binary mixtures. For comparison, the concentration of each solitary compound was doubled to measure bitterness inhibition at the higher intensity level elicited by the mixtures. The following sodium salts were tested for bitterness inhibition: 100 mM sodium chloride (salty), 100 mM sodium gluconate (salty), 100 and 20 mM monosodium glutamate (umami), and 50 mM adenosine monophosphate disodium salt (umami). Sucrose (sweet) was also employed as a bitterness suppressor. The sodium salts differentially suppressed the bitterness of compounds and their binary combinations. Although most bitter compounds were suppressed, the bitterness of tetralone was not suppressed, nor was the bitterness of the binary mixtures that contained it. In general, the percent suppression of binary mixtures of compounds was predicted by the average percent suppression of its two components. Within the constraints of the present study, the bitterness of mixtures was suppressed by sodium salts and sucrose independently, with few bitter interactions. This is consistent with observations that the bitter taste system integrates the bitterness of multi-compound solutions linearly.

Influence of stakeholder communication on consensus making in requirements negotiation

Consensus building is essential in aligning multiple stakeholder viewpoints which are commonly emerging during the process of requirements elicitation, analysis and validation [15]. In fact, agreement among diverse groups of stakeholders is deemed prerequisite to establishing project cooperation and collaboration. While individuals frequently rank the importance of their personal goals over the goals of an organisation, having an appropriate strategy for finding common ground among individuals is crucial to any project's success. This paper therefore explores factors that influence the consensus making process and develops a model that helps with understanding the role of consensus specifically during the elicitation phase of the Requirements Engineering process.

The influence of heat treatment on the corrosion behaviour of as-spun amorphous Al88Ni6La6 alloy in 0.01 M NaCl solution

The effect of the heat treatment on the corrosion behaviour of amorphous Al₈₈Ni₆La₆ made by melt-spun has been investigated by electrochemical measurements. Heat treatment was carried out at 523 K and 673 K for 4 min and 15 min respectively. The evolution of the crystallization process after annealing was identified by differential scanning calorimeter (DSC) as well as X-ray diffraction. The XRD patterns show that the structure of samples heat-treated at higher temperature changes towards a crystal state. The results obtained from the polarization curves reveal that all Al₈₈Ni₆La₆ alloys exhibit spontaneously passivated behaviour. Furthermore, it is noted that the partially crystallized alloy has the best corrosion resistance in comparison with as-spun amorphous and fully crystallized alloys, while the fully crystallized sample shows deterioration in the corrosion resistance.

The prediction of damage condition in regards to damage factor influence of light structures on expansive soils in Victoria, Australia

This paper proposes a neural network model using genetic algorithm for a model for the prediction of the damage condition of existing light structures founded in expansive soils in Victoria, Australia. It also accounts for both individual effects and interactive effects of the damage factors influencing the deterioration of light structures. A Neural Network Model was chosen because it can deal with 'noisy' data while a Genetic Algorithm was chosen because it does not get `trapped' in local optimum like other gradient descent methods. The results obtained were promising and indicate that a Neural Network Model trained using a Genetic Algorithm has the ability to develop an interactive relationship and a Predicted Damage Conditions Model.

Influence of chromium content on the dry machining performance of cathodic arc evaporated TiA1N coatings

Physical vapour deposition (PVD) titanium aluminium nitride coated cutting tools are used extensively in global manufacturing for reducing production costs and improving productivity in a number of aggressive metal-cutting operations, namely, dry and high-speed machining. In this investigation, the performance of Ti1−xAlxN and Ti1−x−yAlxCryN coatings was assessed on Co-HSS twist drills used to machine grey cast iron. The failure criterion for drills was defined as a critical sized flank wear land at the outer corners of the drills. Using this criterion, the average tool life of uncoated twist drills was increased by factors of 2.5, 3.0 and 3.0 by Ti0.59Al0.41N, Ti0.27Al0.19Cr0.54N and Ti0.21Al0.14Cr0.65N coatings, respectively. Notwithstanding the similar increase in average tool life, the Ti1−x−yAlxCryN coatings produced more consistent results than the Ti1−xAlxN coated drills with standard deviations of 67, 3 and 19 holes, respectively. This result has significant practical implications in manufacturing, since drills are not replaced on an individual basis, but rather on a preset tool change frequency. The present paper discusses the performance of Ti1−xAlxN and Ti1−x−yAlxCryN coated drills in terms of average and practical drill life and concludes with remarks on the characterisation of PVD coatings and their significance on the performance of Co-HSS twist drills when dry machining grey cast iron.