Wear characteristics of ultra-hard cutting tools when machining austempered ductile iron

Nodularised Ductile Cast Iron, when subjected to heat treatment processes - austenitising and austempering produces Austempered Ductile Iron (ADI). The microstructure of ADI also known as "ausferrite" consists of ferrite, austenite and graphite nodules. Machining ADI using conventional techniques is often a problematic issue due to the microstructural phase transformation from austenite to martensite during machining. This paper evaluates the wear characteristics of ultra hard cutting tools when machining ADI and its effect on machinability. Machining trials consist of turning ADI (ASTMGrade3) using two sets of PCBN tools with 90% and 50% CBN content and two sets of ceramics tools; Aluminium Oxide Titanium Carbide and Silicon Carbide - whisker reinforced Ceramic. The cutting parameters chosen are categorized as roughing and finishing conditions; the roughing condition comprises of constant cutting speed (425 m/min) and depth of cut (2mm) combined with variable feed rates of 0.1, 0.2, 0.3 and 0.4mm/rev. The finishing condition comprises of constant cutting speed (700 m/min) and depth of cut (0.5mm) combined with variable feed rates of 0.1, 0.2, 0.3 and 0.4mm/rev. The benchmark condition to evaluate the performance of the cutting tools was tool wear evaluation, surface texture analysis and cutting force analysis. The paper analyses thermal softening of the workpiece by the tool and its effect on the shearing mechanism under rough and finish machining conditions in term of lower cutting forces and enhanced surface texture of the machined part.

A case study on effect of feed rate on machinability of austempered ductile iron

Austempered Ductile Iron (ADI) is a type of nodular, ductile cast iron subjected to heat treatments - austenitising and austempering. Whilst machining is conducted prior to heat treatment and offers no significant difficulty, machining post heat treatment is demanding and often avoided. Phase transformation of retained austenite to martensite leading to poor machinability characteristics is a common problem experienced during machining. This case study explains the effect of feed rate on machinability of ADI using cutting force analysis and tool failure analysis. The experimental design consists of conducting drilling trials on grade 1200 and 1400 at constant depth of cut, 25mm; constant speed, 45m/min; no coolant and variable feed rates from 0.2 to 0.35 mm/rev (increment of 0.025mm/rev). Metallography and X-ray diffraction technique was carried out in order to identify and quantify the microstructural phases before and after drilling. The results from the trial infer that the best way to machine ADI efficiently without tool failure is using low feeds and high speeds and without coolant.

Machinability assessment of Ti-6Al-4V for aerospace applications

Titanium alloy Ti-6Al-4V is the most commonly used titanium alloy in the aerospace and biomedical industries due to its superior material properties. An experimental investigation has been carried out to evaluate the machinability of high performance aerospace alloys (Ti-6Al-4V) to determine their in service performance characteristics based on different machining strategies. Nearly 80-90% of the titanium used in airframes is Ti-6Al-4V. The experimental design consist of face milling Ti-6Al-4V at 12 different combinations of cutting parameters consisting of Depth Of Cut (DoC)- 1, 2 and 3 mm; speeds- 60 and 100 m/min; coolant on/off and at constant feed rate of 0.04mm/tooth. Post machining analysis consists of cutting force measurement, surface texture analysis and metallographic analysis. The future work consists of in-depth investigation into the phase transformational reactions during machining.

A preliminary study on machinability assessment of nanobainite steel

The demand for high strength materials and improvements in heat treatment techniques has given rise to this new form of high strength steel known as nanobainite steel. The production of nanobainite steel involves slow isothermal holding of austenitic steel around 200oC for 10 days, in order to obtain a carbon enriched austenite and cooling to room temperature using austempering. The microstructure of nanobainite steel is dual phase consisting of alternate layers of bainitic ferrite and austenite. The experimental design consists of face milling under 12 combination of Depth of Cut (DoC)-1, 2 and 3mm; cutting speed-100 and 150m/min; constant feed- 0.15mm/rev and coolant on/off. The machinability of the material is assessed by means of analysis such as metallography and cutting force analysis. The results obtained are used to assess the most favorable condition to machine this new variety of steel. Future work involves study on phase transformation by quantifying the microstructural phase before and after milling using XRD.

A preliminary assessment of machinability of titanium alloy Ti 6Al 4V during thin wall machining using trochoidal milling

Titanium alloys are of great demand in the aerospace and biomedical industries. Most the titanium products are either cast or sintered to required shape and finish machined to get the appropriate surface texture to meet the design requirements. Ti-6Al-4V is often referred as work horse among the titanium alloys due to its heavy use in the aerospace industry. This paper is an attempt to investigate and improve the machining performance of Ti-6Al-4V. Thin wall machining is an advance machining technique especially used in machining turbine blades which can be done both in a conventional way and using a special technique known as trochoidal milling. The experimental design consists of conducting trials using combination of cutting parameters such as cutting speed (vc), 90 and 120 m/min; feed/tooth (fz) of 0.25 and 0.35 mm/min; step over (ae) 0.3 and 0.2; at constant depth of cut (ap) 20mm and using coolant. A preliminary assessment of machinability of Ti-6Al-4V during thin wall machining using trochoidal milling is done. A correlation established using cutting force, surface texture and dimensional accuracy.

A preliminary study on machinability of super austenitic stainless steel

Stainless steel is the most widely used alloys of steel. The reputed variety of stainless steel having customised material properties as per the design requirements is Duplex Stainless Steel and Austenitic Stainless Steel. The Austenite Stainless Steel alloy has been developed further to be Super Austenitic Stainless Steel (SASS) by increasing the percentage of the alloying elements to form the half or more than the half of the material composition. SASS (Grade-AL-6XN) is an alloy steel containing high percentages of nickel (24%), molybdenum (6%) and chromium (21%). The chemical elements offer high degrees of corrosion resistance, toughness and stability in a large range of hostile environments like petroleum, marine and food processing industries. SASS is often used as a commercially viable substitute to high cost non-ferrous or non-metallic metals. The ability to machine steel effectively and efficiently is of utmost importance in the current competitive market. This paper is an attempt to evaluate the machinability of SASS which has been a classified material so far with very limited research conducted on it. Understanding the machinability of this alloy would assist in the effective forming of this material by metal cutting. The novelty of research associated with this is paper is reasonable taking into consideration the unknowns involved in machining SASS. The experimental design consists of conducting eight milling trials at combination of two different feed rates, 0.1 and 0.15 mm/tooth; cutting speeds, 100 and 150 m/min; Depth of Cut (DoC), 2 and 3 mm and coolant on for all the trials. The cutting tool has two inserts and therefore has two cutting edges. The trial sample is mounted on a dynamometer (type 9257B) to measure the cutting forces during the trials. The cutting force data obtained is later analyzed using DynaWare supplied by Kistler. The machined sample is subjected to surface roughness (Ra) measurement using a 3D optical surface profilometer (Alicona Infinite Focus). A comprehensive metallography process consisting of mounting, polishing and etching was conducted on a before and after machined sample in order to make a comparative analysis of the microstructural changes due to machining. The microstructural images were capture using a digital microscope. The microhardness test were conducted on a Vickers scale (Hv) using a Vickers microhardness tester. Initial bulk hardness testing conducted on the material show that the alloy is having a hardness of 83.4 HRb. This study expects an increase in hardness mostly due to work hardening may be due to phase transformation. The results obtained from the cutting trials are analyzed in order to judge the machinability of the material. Some of the criteria used for machinability evaluation are cutting force analysis, surface texture analysis, metallographic analysis and microhardness analysis. The methodology followed in each aspect of the investigation is similar to and inspired by similar research conducted on other materials. However, the novelty of this research is the investigation of various aspects of machinability and drawing comparisons between each other while attempting to justify each result obtained to the microstructural changes observed which influence the behaviour of the alloy. Due to the limited scope of the paper, machinability criteria such as chip morphology, Metal Removal Rate (MRR) and tool wear are not included in this paper. All aspects are then compared and the optimum machining parameters are justified with a scope for future investigations

Current trends in machinability research

The manufacturing index of a country relies on the quality of manufacturing research outputs. Theemergence of new materials such as composites and multi component alloy has replaced traditionalmaterials in certain design application. Materials with properties like high strength to weight ratio,fatigue strength, wear resistance, thermal stability and damping capacity are a popular choice for adesign engineer. Contrary, the manufacturing engineer is novice to the science of machining thesematerials. This paper is an attempt to focus on the current trends in machinability research and anaddition to the existing information on machining. The paper consist of information on machiningAustempered Ductile Iron (ADI), Duplex Stainless Steel and Nano-Structured Bainitic Steel. Thevarious techniques used to judge the machinability of these materials is described in this paper.Studying the chip formation process in duplex steel using a quick stop device, metallographic analysisusing heat tinting of ADI and cutting force analysis of Nano-structured bainitic steel is discussed.

Machinability assessment of multi component high entropy alloys

Due to high demand in engineering materials especially with high strength to weight ratio and advantageous material properties such as wear resistance and thermal stability or high entropy. This essential parametric enhancement has led to the development of Multi Component High Entropy Alloys (MCHEA). It has been proposed in this study to investigate the machinability characteristics of MCHEA. The MCHEA are usually amalgamation with multiple elements such as aluminium, cobalt, manganese, nickel, chromium and titanium with their individual concentrations ranging from 5-35% overall. The experimental design consists of basic characterization of the material and conducting machinability trails-milling. The basic material characterization consists of evaluating bulk hardness, microstructural image generation, microhardness and chemical composition using spectrometry. The milling trails are conducted using 2 flute, 30º helix ball nose solid carbide end-mill cutting tool with combination of cutting parameters such as constant cutting speed, 30 m/min; varied feed, 0.01 mm/tooth and 0.02mm/tooth; depth of cuts, 1.5 and 3 mm and coolant on. The outputs obtained from the machining trails are subjected to analysis such as cutting force. In addition, the surface roughness of the material is evaluated using 3D optical surface profilometer. Similarly, the solutions to alleviate the drawbacks are also exemplified during machining of MCHEA.

An improved static model for tool deflection in machining of Ti–6Al–4V acetabular shell produced by selective laser melting

Tool deflection during milling operation leads to dimensional error, decreasing surface quality and increasing rejection rate. In this study, tool deflection during the milling of the inner surfaces of Ti–6Al–4V prosthetic acetabular shell produced by selective laser melting (SLM) was modelled. The first purpose of this research is to provide a general static cutting tool deflection model for ball nose cutters where deviation of machine components and tool holder are so small as to be considered negligible. This is because the values of machine component and tool holder deflection were lower than standard tolerances (10 μm) and found to be lower than 1/15 of tool deflection. The second and third objectives of this work involve calculating contact surfaces by determining workpiece and tool geometry and choosing second moment of inertia using a novel cross section method (CSM). Static models for three quasi-analytical methods (QAM) that are simple cantilever beam model (SCBM), two-section model (TWSM) and our three section model (THSM) are presented. THSM showed high accuracy which was validated by 3D finite element method (FEM3D) and experimental measurements. The accuracy of tool deflection calculation using THSM by computing, shank, flute and ball head deflection and also utilizing CSM to determine second moment of inertia showed notable improvements.

Metallurgical and machinability characteristics of wrought and selective laser melted Ti-6Al-4V

This research work presents a machinability study between wrought grade titanium and selective laser melted (SLM) titanium Ti-6Al-4V in a face turning operation, machined at cutting speeds between 60 and 180 m/min. Machinability characteristics such as tool wear, cutting forces, and machined surface quality were investigated. Coating delamination, adhesion, abrasion, attrition, and chipping wear mechanisms were dominant during machining of SLM Ti-6Al-4V. Maximum flank wear was found higher in machining SLM Ti-6Al-4V compared to wrought Ti-6Al-4V at all speeds. It was also found that high machining speeds lead to catastrophic failure of the cutting tool during machining of SLM Ti-6Al-4V. Cutting force was higher in machining SLM Ti-6Al-4V as compared to wrought Ti-6Al-4V for all cutting speeds due to its higher strength and hardness. Surface finish improved with the cutting speed despite the high tool wear observed at high machining speeds. Overall, machinability of SLM Ti-6Al-4V was found poor as compared to the wrought alloy.

Force measurement capability for robotic assisted minimally invasive surgery systems

An automated laparoscopic instrument capable of non-invasive measurement of tip/tissue interaction forces for direct application in robotic assisted minimally invasive surgery systems_ is introduced in this paper. It has the capability to measure normal grasping forces as well as lateral interaction forces without any sensor mounted on the tip jaws. Further to non-invasive actuation of the tip, the proposed instrument is also able to change the grasping direction during surgical operation. Modular design of the instrument allows conversion between surgical modalities (e.g., grasping, cutting, and dissecting). The main focus of this paper is on evaluation of the grasping force capability of the proposed instrument. The mathematical formulation of fenestrated insert is presented and its non-linear behaviour is studied. In order to measure the stiffness of soft tissues, a device was developed that is also described in this paper. Tissue characterisation experiments were conducted and results are presented and analysed here. The experimental results verify the capability of the proposed instrument in accurately measuring grasping forces and in characterising artificial tissue samples of varying stiffness.

Soft tissue characterisation using a force feedback-enabled instrument for robotic assisted minimally invasive surgery systems

An automated laparoscopic instrument capable of non-invasivemeasurement of tip/tissue interaction forces for direct application in robotic assisted minimally invasive surgery systems is introduced in this chapter. It has the capability to measure normal grasping forces as well as lateral interaction forces without any sensor mounted on the tip jaws. Further to non-invasive actuation of the tip, the proposed instrument is also able to change the grasping direction during surgical operation. Modular design of the instrument allows conversion between surgical modalities (e.g., grasping, cutting, and dissecting). The main focus of thispaper is on evaluation of the grasping force capability of the proposed instrument. The mathematical formulation of fenestrated insert is presented and its non-linear behaviour is studied. In order to measure the stiffness of soft tissues, a device was developed that is also described in this chapter. Tissue characterisation experiments were conducted and results are presented and analysed here. The experimental results verify the capability of the proposed instrument in accurately measuring grasping forces and in characterising artificial tissue samples of varying stiffness.

Fast algorithm for the cutting angle method of global optimization

The cutting angle method for global optimization was proposed in 1999 by Andramonov et al. (Appl. Math. Lett. 12 (1999) 95). Computer implementation of the resulting algorithm indicates that running time could be improved with appropriate modifications to the underlying mathematical description. In this article, we describe the initial algorithm and introduce a new one which we prove is significantly faster at each stage. Results of numerical experiments performed on a Pentium III 750 Mhz processor are presented.