Improved efficiency and stability of flexible dye sensitized solar cells on ITO/PEN substrates using an ionic liquid electrolyte

Flexible dye-sensitized solar cells (DSSCs) built on plastic substrates have attracted great interest as they are lightweight and can be roll-to-roll printed to accelerate production and reduce cost. However, plastic substrates such as PEN and PET are permeable to water, oxygen and volatile electrolyte solvents, which is detrimental to the cell stability. Therefore, to address this problem, in this work, an ionic liquid (IL) electrolyte is used to replace the volatile solvent electrolyte. The initial IL-based devices only achieved around 50% of the photovoltaic conversion efficiency of the cells using the solvent electrolyte. Current-voltage and electrochemical impedance spectroscopy (EIS) analysis of the cells in the dark indicated that this lower efficiency mainly originated from (i) a lack of blocking layer to reduce recombination, and (ii) a lower charge collection efficiency. To combat these problems, cells were developed using a 12 nm thick blocking layer, produced by atomic layer deposition, and 1 μm thick P25 TiO2 film sensitized with the hydrophobic MK-2 dye. These flexible DSSCs utilizing an IL electrolyte exhibit significantly improved efficiencies and a <10% drop in performance after 1000 h aging at 60°C under continuous light illumination.

Organic Solvent-Based Graphene Oxide Liquid Crystals: A Facile Route toward the Next Generation of Self-Assembled Layer-by-Layer Multifunctional 3D Architectures

We introduce soft self-assembly of ultralarge liquid crystalline (LC) graphene oxide (GO) sheets in a wide range of organic solvents overcoming the practical limitations imposed on LC GO processing in water. This expands the number of known solvents which can support amphiphilic self-assembly to ethanol, acetone, tetrahydrofuran, N-dimethylformamide, N-cyclohexyl-2-pyrrolidone, and a number of other organic solvents, many of which were not known to afford solvophobic self-assembly prior to this report. The LC behavior of the as-prepared GO sheets in organic solvents has enabled us to disperse and organize substantial amounts of aggregate-free single-walled carbon nanotubes (SWNTs, up to 10 wt %) without compromise in LC properties. The as-prepared LC GO-SWNT dispersions were employed to achieve self-assembled layer-by-layer multifunctional 3D hybrid architectures comprising SWNTs and GO with unrivalled superior mechanical properties (Young’s modulus in excess of 50 GPa and tensile strength of more than 500 MPa).

Compact stacked planar inverted-F antenna for passive deep brain stimulation implants

A compact meandered three-layer stacked circular planar inverted-F antenna is designed and simulated at the UHF band (902.75 – 927.25 MHz) for passive deep brain stimulation implants. The UHF band is used because it offers small antenna size, and high data rate. The top and middle radiating layers are meandered, and low cost substrate and superstrate materials are used to limit the radius and height of the antenna to 5 mm and 1.64 mm, respectively. A dielectric substrate of FR-4 of εr= 4.7 and δ= 0.018, and a biocompatible superstrate of silicone of er= 3.7 and d= 0.003 with thickness of 0.2 mm are used in the design. The resonance frequency of the proposed antenna is 918 MHz with a bandwidth of 24 MHz at return loss of −10 dB in free space. The antenna parameter such as 3D gain pattern of the designed antenna within a skin-tissue model is evaluated by using the finite element method. The compactness, wide bandwidth, round shape, and stable characteristics in skin make this antenna suitable for DBS. The feasibility of the wireless power transmission to the implant in the human head is also examined.

Nanotechnology-based coating techniques for smart textiles

Nanotechnology-based textile coating is a combined approach to textile engineering which mainly relies on using nanoscale materials and novel methods to produce smart finishing. Several methods have been introduced to generate smart coatings on textiles including the sol–gel technique, layer-by-layer technique, cross-linking by polymers, and thin film deposition. Nanofibre coating of different metallic and nonmetallic substrates has been intensively considered for sensory and infrastructure purposes. This chapter provides an overview of nanotechnology-based coating approaches with a detailed discussion of applications in practical and potential fields. Future trends of new types of smart coatings on textiles are also presented.

Sol-gel derived HA/TiO2 double coatings on Ti scaffolds for orthopaedic applications

Hydroxyapatite/titania (HA/TiO₂) double layers were coated onto Ti scaffolds throughout for orthopaedic applications by sol-gel method. Differential scanning calorimetry (DSC), thermogravimetric analysis (TG) and X-ray diffractometry (XRD) were used for the characterisation of the phase transformations of the dried gels and coated surface structures. Scanning electron microscope (SEM) equipped with energy dispersive spectrometry (EDS) was used for the observation and evaluation of the morphology and phases of the surface layers and for the assessment of the in vitro tests. The in vitro assessments were performed by soaking the HA/TiO₂ double coated samples into the simulated body fluid (SBF) for various periods. The TiO₂ layer was coated by a dipping-coating method at a speed of 12 cm/min, followed by a heat treatment at 600 °C for 20 min. The HA layer was subsequently dipping-coated on the outer surface at the same speed and then heat-treated at difference temperatures. The results indicat that the HA phase begins to crystallize after a heat treatment at 560 °C. The crystallinity increases obviously at 760 °C. SEM observations find no delamination or crack at the interfaces of HA/TiO₂ and TiO₂/Ti. The HA/TiO₂ coated Ti scaffolds displays excellent bone-like apatite forming ability when it is soaked into SBF. Ti scaffolds after HA/TiO₂ double coatings can be anticipated as promising implant materials for orthopaedic applications

Visible transparent, UV-blocking polymer nanocomposite films containing nano-sized organic-LDH (Layered Double Hydroxide) hybrid

A nano-sized Mg2Al layered double hydroxide (LDH) was used for encapsulating an organic UV absorber, 2-hydroxy-4- methoxybenzeophenone-5-sulfonic acid (HMBS), to produce HMBS@LDH hybrid nano-platelets. Upon dispersing this organic-inorganic hybrid LDH into ethylene-vinyl alcohol copolymer (EVOH) for film casting, a thin polymer
nanocomposite film that is UV opaque but highly transparent to visible light (higher than 90%) was formed. Thermogravimetry (TG) analysis confirmed that the intercalation of HMBS into LDH considerably increased the thermal stability of HMBS. Such an improvement was attributed to the strong guest-host interaction between the HMBS anions and the LDH layers. Also, the nanocomposite films were flexible and had good mechanical properties.

Synthesis and growth mechanism of Thin-film TiO2 nanotube arrays on focused-ion-beam micropatterned 3D isolated regions of titanium on silicon

In this paper, the fabrication and growth mechanism of net-shaped micropatterned self-organized thin-film TiO2 nanotube (TFTN) arrays on a silicon substrate are reported. Electrochemical anodization is used to grow the nanotubes from thin-film titanium sputtered on a silicon substrate with an average diameter of ?30 nm and a length of ?1.5 ?m using aqueous and organic-based types of electrolytes. The fabrication and growth mechanism of TFTN arrays from micropatterned three-dimensional isolated islands of sputtered titanium on a silicon substrate is demonstrated for the first time using focused-ion-beam (FIB) technique. This work demonstrates the use of the FIB technique as a simple, high-resolution, and maskless method for high-aspect-ratio etching for the creation of isolated islands and shows great promise toward the use of the proposed approach for the development of metal oxide nanostructured devices and their integration with micro- and nanosystems within silicon-based integrated-circuit devices.

Improvement of light harvesting and device performance of dye-sensitized solar cells using rod-like nanocrystal TiO2 overlay coating on TiO2 nanoparticle working electrode

Novel TiO2 single crystalline nanorods were synthesized by electrospinning and hydrothermal treatment. The role of the TiO2 nanorods on TiO2 nanoparticle electrode in improvement of light harvesting and photovoltaic properties of dye-sensitized solar cells (DSSCs) was examined. Although the TiO2 nanorods had lower dye loading than TiO2 nanoparticle, they showed higher light utilization behaviour. Electron transfer in TiO2 nanorods received less resistance than that in TiO2 nanoparticle aggregation. By just applying a thin layer of TiO2 nanorods on TiO2 nanoparticle working electrode, the DSSC device light harvesting ability and energy conversion efficiency were improved significantly. The thickness of the nanorod layer in the working electrode played an important role in determining the photovoltaic property of DSSCs. An energy conversion efficiency as high as 6.6% was found on a DSSC device with the working electrode consisting of a 12 μm think TiO2 nanoparticle layer covered with 3 μm thick TiO2 nanorods. The results obtained from this study may benefit further design of highly efficient DSSCs.

Experimental study of the degradation of volatile organic compounds by photocatalytic oxidation using TiO2 pellets

A fixed bed photocatalytic reactor has been designed and built with a UV
radiation source. Ti02 pellets were placed on the three fixed beds within the
reactor. Acetone was used as an indicator of volatile organic compounds (VOCs) during the experiment. Under the flow rate of 12.75 l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranged from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency; the obtained oxidation efficiency was in the range of 40-70% for various concentrations of untreated gases.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

Hydroxyapatite/titania sol-gel coatings on titanium-zirconium alloy for biomedical applications

A simple sol–gel method was developed for hydroxyapatite/titania (HA/TiO2) coatings on non-toxic titanium–zirconium (TiZr) alloy for biomedical applications. The HA/TiO2-coated TiZr alloy displayed excellent bioactivity when soaked in a simulated body fluid (SBF) for an appropriate period. Differential scanning calorimetry, thermogravimetric analysis, X-ray diffraction and scanning electron microscopy-energy dispersive spectrometry were used to characterize the phase transformations and the surface structures and to assess the in vitro tests. The HA/TiO2 layers were spin-coated on the surface of TiZr alloy at a speed of 3000 rpm for 15 s, followed by a heat treatment at 600 °C for 20 min in an argon atmosphere sequentially. The TiO2 layer exhibited a cracked surface and an anatase structure and the HA layer displayed a uniform dense structure. Both the TiO2 and HA layers were 25 μm thick, and the total thickness of the HA/TiO2 coatings was 50 μm. The TiZr alloy after the above HA/TiO2 coatings displayed excellent bone-like apatite-forming ability when soaked in SBF and can be anticipated to be a promising load-bearing implant material.

Sol-gel derived hydroxyapatite/titania biocoatings on titanium substrate

A simple sol–gel method was successfully developed for a hydroxyapatite (HA)/TiO₂ double layer deposition on a pure titanium substrate. Phase formation, surface morphology, and interfacial microstructure were investigated by differential scanning calorimetry analysis (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The TiO₂ layer was coated by a spin coating method at a speed of 1500 rpm for 15 s, followed by a heat treatment at 560 °C for 20 min. The HA film was subsequently spin coated on the outer surface at the same speed and then heat-treated at difference temperatures. Results indicated that the HA phase began to crystallize after a heat treatment at 580 °C; and the crystallinity increased obviously at a temperature of 780 °C. The HA film showed a porous structure and a thickness of 5–7 μm after the heat treatment at 780 °C. SEM observations revealed no delamination and crack at the interfaces of HA/TiO₂ and TiO₂/Ti. The HA film with a porous structure is expected to be more susceptible to the natural remodeling processes when it is implanted in a living body.