Landfill leachate treatment using thermophilic membrane bioreactor

This study was undertaken to investigate the performance of aerobic thermophilic membrane bioreactor (MBR) treating raw landfill leachate from two landfill sites in Thailand (Pathumthani site and Ram Indra site). The leachates from these sites were mixed in different proportions to produce a BOD/COD ratio of 0.39, 0.57, and 0.65, which was investigated in 3 experimental runs. The COD, ammonia, and TKN composition of the mixed leachate was 12,000, 1700 and 1900 mg/L, respectively. BOD was supplemented with glucose and soy protein. The system was operated at 45 degrees C and at a hydraulic retention time (HRT) of 24 hrs. The membrane used was a ceramic membrane with an ‘‘outside-in’’ flow mode and consisted of 22 open fibres with an inner diameter of approximately 2 mm. The COD removal rate increased from an average value of 62–79% while ammonia removal efficiency decreased from 75 to 60% with gradual increase in BOD. Furthermore, a high BOD removal efficiency (97–99%) was also observed. This clearly indicates that thermophilic system is highly suitable for COD and BOD removal especially at elevated organic loading. However, the system does not favor high nitrogen content wastewaters as the ammonia removal efficiency dropped with increasing BOD/COD ratio. Similar trends were found in TKN analysis as well. However, this system could serve as a pretreatment in removing ammonia. The concentrations of soluble and bound extra-cellular polymeric substances (EPS) found in thermophilic MBR were higher when compared to the corresponding concentrations in a mesophilic MBR, which led to a higher rate of fouling in the thermophilic membrane.

Using inorganic polymer to reduce leach rates of metals from brown coal fly ash

The burning of brown coal for electricity generation produces thousands of tonnes of fly ash each year. Treatment of the fly ash can reduce leach rates of metals and allow it to be disposed in less prescribed landfill. A geopolymer matrix was investigated as a potential stabilisation method for fly ash obtained from electrostatic precipitators and ash disposal ponds. The ratio of fly ash and geopolymer was varied to determine the effects of different compositions on leaching rates. The major element leachate concentrations obtained from pond ash were lower than that of precipitator fly ash. Conversely, precipitator ash-geopolymers were better for trace heavy metal stabilisation. Effective reduction of elemental concentrations in the leachate has been achieved, particularly for calcium, arsenic, selenium, strontium and barium. Scanning electron microscopy revealed the distribution of metals originated from fly ash and from added geopolymer material. It also showed that some elements are leached from ash particles to the geopolymer phase and others remained as undissolved particles. Qualitative analysis showed that fly ash particles interacted with the geopolymers phase through surface reactions.

Facilitated heterogeneous photodegradation of dissolved organic matter by particulate iron

The photochemical degradation of dissolved organic matter (DOM) derived from the leaves of River Red Gum (Eucalyptus camaldulensis) was examined, with a particular focus on the photochemical generation of CO₂, consumption of O₂, and the effect of particulate iron minerals on these photochemical reactions. Solutions of leaf leachate were irradiated with ultraviolet and visible light in the presence and absence of amorphous iron oxides. Addition of fresh iron oxide was found to increase the rate of photodegradation of the organic matter by up to an order of magnitude compared to the reactions without added iron oxide. The ratio of CO₂ produced to O₂ consumed was ~1:1 in both the presence and absence of iron oxyhydroxide. The reactivity of the iron oxides was dependent on the preparation method and decreased with increased storage time. These results suggest that photochemical reactions on particle surfaces should be considered when examining carbon transformation in aquatic ecosystems, especially at sites with potential for the production of iron oxyhydroxides.

Using geopolymer to minimise metals leaching from brown coal fly ash

Fly ash is generated from combustion of brown coal in power stations. The majority of fly ash is removed by electrostatic precipitators (ESP) and finally disposed into the landfill as prescribed wastes. A method was studied to add clay materials to the brown coal fly ash in order to form the so-called geopolymer network, which is effective at stopping the metal contents from leaching, and have minimum impact to the environment. The experiments were conducted parallel on leached fly ash and dry precipitator fly ash. The ratios of fly ash and added clay materials were varied to determine the effects of different compositions on leaching rates. Both X-ray diffraction analysis and scanning electron microscopy images showed that as the percentage of fly ash was increased, the formation of geopolymer is reduced. Eighteen metals and heavy metals were targeted during the leaching tests and the leachate samples were analysed using ICP-AES and ICP-MS. It was found that the reduction of metal leaching was achieved by adding up to 60% of fly ash to form the geopolymer like structure. Significant reductions were observed for calcium, strontium and barium. Leached fly ash achieved better stabilisation than dry precipitator fly ash for major elements. It's hard to quantify its effects on trace metals leaching due to their ultra low concentration in the fly ash. The samples spiked with trace metals of lead, zinc, mercury and barium showed remarkable reduction in leaching.

Modelling the fate of chromated copper arsenate in a sandy soil

A pulse of chromated copper arsenate (CCA, a timber preservative) was applied in irrigation water to an undisturbed field soil in a laboratory column. Concentrations of various elements in the leachate from the column were measured during the experiment. Also, the remnants within the soil were measured at the end of the experiment. The geochemical modelling package, PHREEQC-2, was used to simulate the experimental data. Processes included in the CCA transport modelling were advection, dispersion, non-specific adsorption (cation exchange) and specific adsorption by clay minerals and organic matter, as well as other possible chemical reactions such as precipitation/dissolution. The modelling effort highlighted the possible complexities in CCA transport and reaction experiments. For example, the uneven dosing of CCA as well as incomplete knowledge of the soil properties resulted in simulations that gave only partial, although reasonable, agreement with the experimental data. Both the experimental data and simulations show that As and Cu are strongly adsorbed and therefore, will mostly remain at the top of the soil profile, with a small proportion appearing in leachate. On the other hand, Cr is more mobile and thus it is present in the soil column leachate. Further simulations show that both the quantity of CCA added to the soil and the pH of the irrigation water will influence CCA transport. Simulations suggest that application of larger doses of CCA to the soil will result in higher leachate concentrations, especially for Cu and As. Irrigation water with a lower pH will dramatically increase leaching of Cu. These results indicate that acidic rainfall or significant accidental spillage of CCA will increase the risk of groundwater pollution.

Photodegradation, interaction with iron oxides and bioavailability of dissolved organic matter from forested floodplain sources

Photochemical degradation of dissolved organic matter (DOM) can influence food webs by altering the availability of carbon to microbial communities, and may be particularly important following periods of high DOM input (e.g. flooding of forested floodplains). Iron oxides can facilitate these reactions, but their influence on subsequent organic products is poorly understood. Degradation experiments with billabong (= oxbow lake) water and river red gum (Eucalyptus camaldulensis) leaf leachate were conducted to assess the importance of these reactions in floodplain systems. Photochemical degradation of DOM in sunlight-irradiated quartz tubes (with and without amorphous iron oxide) was studied using gas chromatography and UV-visible spectroscopy. Photochemical reactions generated gaseous products and small organic acids. Bioavailability of billabong DOM increased following irradiation, whereas that of leaf leachate was not significantly altered. Fluorescence excitation-emission spectra suggested that the humic component of billabong organic matter was particularly susceptible to degradation, and the source of DOM influenced the changes observed. The addition of amorphous iron oxide increased rates of photochemical degradation of leachate and billabong DOM. The importance of photochemical reactions to aquatic systems will depend on the source of the DOM and its starting bioavailability, whereas inputs of freshly formed iron oxides will accelerate the processes.

Analysis of residues of prometryne and acetochlor in soil-water system by solid-phase extraction and gas chromatography/mass spectrometry

A highly sensitive and simple analytical method was developed for analyzing the binary mixed pesticides of prometryne and acetochlor in soil–water system by gas chromatography/mass spectrometry (GC/MS). The sample solution was first purified by C18 solid-phase extraction column, which was leached by acetone. The leachate was enriched to 1.0 mL by pressure blowing concentrator and then analyzed by GC/MS. The linear calibration curves were showed in the range of 1–15 μg/mL with a correlation coefficient of 0.9991. The average recoveries (n = 5) were between 95.3 and 115.7%, with relative standard deviations ranged from 1.71 and 7.95%. The limits of detection of Prometryne/Acetochlor were up to 0.06 and 0.17 μg/mL, respectively. This method provides a reliable approach to examine and evaluate the residues of prometryne and acetochlor in the soil–water system.