FT-IR investigation of Ion association in plasticized solid polymer electrolytes

FT-IR spectroscopy has been utilized to monitor ion association in plasticized solid polymer electrolytes (SPEs). The SPEs were prepared from a random copolymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethanesulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethyl ether (tetraglyme) and N,N‘-dimethylformamide (DMF) were chosen as model plasticizers. Despite having a similar dielectric constant to that of the polymer host, ε ~ 5, the incorporation of tetraglyme into the SPEs resulted in increased ion association. The addition of a higher dielectric constant solvent , DMF, ε = 36.7, resulted in decreased ion association in the SPE. The effects of salt concentration (0.05−1.25 mol dm^-3) and temperature (25−100 °C) upon ion association in SPEs were also investigated. At low salt concentrations, ion association was found to increase with temperature, however, at 1.25 mol dm^-3 the temperature dependence of ion association was dominated by concentration effects. There appears to be a maximum in the fraction of “free” ions at a LiCF₃SO₃ concentration of 0.4 mol dm^-3, preceded by a minimum at approximately 0.2 mol dm^-3, consistent with the molar conductivity behavior previously observed in these electrolytes.

ATR FT-IR absorption enhancement of a thin film under the photon-tunneling condition

A simple, yet very powerful technique for the spectral acquisition of an extremely thin film with enhanced absorption was explored. An infrared absorption of an extremely thin film confined between media of high refractive indices was greater than that of its bulk when the spectrum was acquired under the attenuated total reflection (ATR) condition with parallel (p) polarized radiation. The absorption enhancement was not observed under perpendicular (s) polarized radiation. Theoretical investigations indicated that the absorption enhancement was proportional to the integration of the mean square evanescent field within the film. The field integration under p-polarized radiation increased, while that under s-polarized radiation decreased as the thickness of the confined film became thinner. The maximum enhancement was observed when the film was sufficiently thinner than the penetration depth. The phenomena were experimentally investigated, and the results agreed very well with theoretical predictions.

Vesselness features and the inverse compositional AAM for robust face recognition using thermal IR

Over the course of the last decade, infrared (IR) and particularly thermal IR imaging based face recognition has emerged as a promising complement to conventional, visible spectrum based approaches which continue to struggle when applied in the real world. While inherently insensitive to visible spectrum illumination changes, IR images introduce specific challenges of their own, most notably sensitivity to factors which affect facial heat emission patterns, e.g. emotional state, ambient temperature, and alcohol intake. In addition, facial expression and pose changes are more difficult to correct in IR images because they are less rich in high frequency detail which is an important cue for fitting any deformable model. In this paper we describe a novel method which addresses these major challenges. Specifically, to normalize for pose and facial expression changes we generate a synthetic frontal image of a face in a canonical, neutral facial expression from an image of the face in an arbitrary pose and facial expression. This is achieved by piecewise affine warping which follows active appearance model (AAM) fitting. This is the first publication which explores the use of an AAM on thermal IR images; we propose a pre-processing step which enhances detail in thermal images, making AAM convergence faster and more accurate. To overcome the problem of thermal IR image sensitivity to the exact pattern of facial temperature emissions we describe a representation based on reliable anatomical features. In contrast to previous approaches, our representation is not binary; rather, our method accounts for the reliability of the extracted features. This makes the proposed representation much more robust both to pose and scale changes. The effectiveness of the proposed approach is demonstrated on the largest public database of thermal IR images of faces on which it achieved 100% identification rate, significantly outperforming previously described methods

Aging studies on conducting polypyrrole

Change of tensile properties, electrical conductivity and microwave shielding of electrochemically synthesized polypyrrole films with time are presented. Highly doped films had good electrical stability, retaining high microwave reflectivity throughout the aging period. Lightly doped films were less stable and partially reflective and absorptive of microwaves. FT-IR spectral observations revealed a progressive increase in intensity of an unsaturated conjugated carbonyl peak, which was not observed in the highly doped films, suggesting that the concentration of the dopant had an influence on the mechanism of degradation of conductivity.

Characterization of superfine wool powder/poly(propylene) blend film

Superfine wool powder was blended and extruded with poly(propylene) (PP) to produce blend pellets, and the extruded pellets were hot-pressed into a blend film. SEM photographs show that the powder could be uniformly incorporated with PP after extrusion. FT-IR spectra shows that no substantial changes occurred in the chemical structure of both PP and wool powder in the blend film. X-Ray diffraction analysis indicates that crystallinity of the blend film was much higher than that of the wool powder and little lower than that of PP. TG-tested results indicate that the thermal stability of the blend film declined with an increase in the powder content. Endothermic peaks of the wool powder in the blend film become more obvious as the powder content increases. Mechanical properties decline greatly with an increase in the wool powder content in the blend film.

Fourier transform infrared microspectroscopy as a tool to identify macroalgal propagules

Understanding of macroalgal dispersal has been hindered by the difficulty in identifying propagules. Different carrageenans typically occur in gametophytes and tetrasporophytes of the red algal family Gigartinaceae, and we may expect that carpospores and tetraspores also differ in composition of carrageenans. Using Fourier transform infrared (FT-IR) microspectroscopy, we tested the model that differences in carrageenans and other cellular constituents between nuclear phases should allow us to discriminate carpospores and tetraspores of Chondrus verrucosus Mikami. Spectral data suggest that carposporophytes isolated from the pericarp and female gametophytes contained κ-carrageenan, whereas tetrasporophytes contained λ-carrageenan. However, both carpospores and tetraspores exhibited absorbances in wave bands characteristic of κ-,ι-, and λ-carrageenans. Carpospores contained more proteins and may be more photosynthetically active than tetraspores, which contained more lipid reserves. We draw analogies to planktotrophic and lecithotrophic larvae. These differences in cellular chemistry allowed reliable discrimination of spores, but pretreatment of spectral data affected the accuracy of classification. The best classification of spores was achieved with extended multiplicative signal correction (EMSC) pretreatment using partial least squares discrimination analysis, with correct classification of 86% of carpospores and 83% of tetraspores. Classification may be further improved by using synchrotron FT-IR microspectroscopy because of its inherently higher signal-to-noise ratio compared with microspectroscopy using conventional sources of IR. This study demonstrates that FT-IR microspectroscopy and bioinformatics are useful tools to advance our understanding of algal dispersal ecology through discrimination of morphologically similar propagules both within and potentially between species.

Electrostatic complex of didodecyldimethylammonium and DNA: Langmuir monolayer, Langmuir–Blodgett film and dye recognition at air/water interface

DNA–didodecyldimethylammonium (DNA–DDDA) electrostatic complex was prepared and characterized through Fourier transformation infrared (FT-IR), 1H NMR and circular dichroism (CD) spectroscopy. When the dye molecule aqueous solutions were used as the subphase, the interaction between three dye molecules, acridine orange (AO), ethidium bromide (EB) and 5,10,15,20-tetrakis(4-N-methylpyridyl)porphine tetra(p-toluenesulfonate) (TMPyP) and the complex at air/solution interface were investigated through the surface pressure–area (π–A) isotherms, Brewster angle microscopy and UV-Vis spectroscopy, respectively. Our investigation indicates that the interaction capabilities of the three dyes to DNA–DDDA complex are different and present an order of TMPyP>AO>EB. For the interaction forms, we believe that TMPyP intercalates into the double helix of DNA, and AO adsorbs onto the surface of the DNA. As for EB, the measured signal is too weak to give a definite interaction form in the present experiment.

Pulsed plasma polymerization of hexamethyldisiloxane onto wool : control of moisture vapor transmission rate and surface adhesion

A new fabric with potential in medical textiles has been developed by application of a surface coating on wool using pulsed plasma polymerization of HMDSO. This coating enabled a controllable MVTR and surface adhesion. MVTR in the range recommended for optimum wound healing was obtained by varying frequency, monomer pressure and deposition time. Lower surface adhesion was achieved. Peeling tests, contact angle measurements, SPM force curves and ATR FT-IR were used to characterize the surfaces for both wool and a PE model substrate. All these results were consistent with a decrease in surface energy after PP-HMDSO treatment. ATR FT-IR results showed a siloxane film with less organic Si(CH₃)_n groups and more SiOSi cross-links.

Ion association and molar conductivity in polyether electrolytes

The ion association behaviour observed in our earlier studies of a polyether electrolyte system at elevated temperatures, was reminiscent of the molar conductivity behaviour typical of low dielectric constant systems. Further investigation of this relationship has led to some suggestions about the types of ionic species present in the polymer electrolyte systems. FT-IR spectroscopy has been used in this work to contrast ion association in an amorphous polyether electrolyte with two liquid electrolytes, N,N-dimethyl-formamide and tetraethylenegylcol dimethylether, containing lithium trifluoromethan sulfonate.

Triflate ion association in plasticized polymer electrolytes

Ion association in plasticised solid polymer electrolytes (SPEs) has been monitored using FT-IR spectroscopy. The SPEs were prepared from a random co-polymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethane sulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethylether (tetraglyme, ε˜5) and N,N'-dimethyl formamide (DMF, ε = 36.7) were chosen as model plasticisers. Decreased ion association resulted from plasticization with DMF, indicating that the addition of a higher dielectric constant solvent increases the fraction of dissociated ions in the SPE. The incorporation of tetraglyme into these SPEs results in increased ion association, despite the similar dielectric constants of the plasticiser and polymer host. The effects of salt concentration (0.05–1.25 mol dm^{− 3} solvent) upon ion association in SPEs was also investigated. There appears to be a minimum in the number of “free” ions at a LiTf concentration of 0.2 mol dm^{− 3} solvent followed by a maximum at approximately 0.4 mol dm^{− 3} solvent, consistent with the molar conductivity behaviour previously observed in these electrolytes.

Ionic liquid electrolyte for lithium metal batteries : physical, electrochemical, and interfacial studies of N-Methyl-N-butylmorpholinium Bis(fluorosulfonyl)imide

The ionic liquid (IL) N-methyl-N-butylmorpholinium bis(fluorosulfonyl)imide (C₄mmor FSI) is examined from physical and electrochemical perspectives. Pulsed field gradient NMR spectroscopy shows that ion diffusivities are low compared with similar, non-ethereal ILs. Ionicity values indicate that above room temperature, less than 50% of ions contribute to conductivity.

Lithium cycling in symmetrical cells using a C₄mmor FSI-based electrolyte is best demonstrated at elevated temperatures. Specific capacities of 130 mAh g⁻¹ are achieved in a Li−LiFePO₄ battery at 85 °C. FT-IR spectroscopic investigations of lithium electrodes suggest the presence of alkoxide species in the solid electrolyte interphase (SEI), implying a ring-opening reaction of C₄mmor with lithium metal. In contrast, the SEI derived from N-methyl-N-propylpiperidinium FSI lacks the alkoxide signature but shows signs of alkyl unsaturation, and the activation energy for Li+ transport through this SEI is slightly lower than that for the C₄mmor-derived SEI. Our detailed findings give insight into the capabilities and limitations of rechargeable lithium metal batteries utilizing a C₄mmor FSI electrolyte.

UV absorption property of bamboo

This article describes ultra violet (UV) light shielding behaviour of Australian grown bamboo (Phyllostachys pubescens). Optical reflectance showed that untreated bamboo plant has UV absorption properties. To reveal the origin of the UV absorption property, its chemical components were extracted using several polar and non-polar solvents. The extracts in most of the polar and non-polar solvents showed UV absorption property. Protic polar solvents showed better ability to extract UV absorbing chemicals than aprotic and non-polar solvents, except hexane. The chemical components of bamboo were analysed by FT-IR spectroscopy and the findings were correlated with the UV absorbance characteristics. The results confirmed that the UV absorption ability of bamboo originates from nothing but lignin. It is thus indicated that the conventional methods to manufacture bamboo fibres, such as complete degumming or viscose methods, that involve the removal of lignin, cannot retain the unique UV absorption property of bamboo plant in bamboo fibres.

Synthesis of high surface area amorphous tin-zinc oxides by a sol-gel method

A new method to synthesize conducting oxide nanoparticles with low photocatalytic activity was investigated. Initially, the preparation of amorphous ZnO-SnO2 solid solution nanoparticles was studied using a sol-gel technique. It was found that X-ray amorphous nanopowders with low photocatalytic activity were produced when the precipitates were heat treated below 500 °C. However, FT-IR data showed that the sample may not be an oxide semiconductor. A mixture of ZnO and SnO2 crystalline nanoparticles was also produced at 800 °C and found to have much reduced photoactivity than commercial ZnO nanoparticles having a similar specific surface area.

Toughening of a carbon-fibre composite using electrospun poly(Hydroxyether of Bisphenol A) nanofibrous membranes through inverse phase separation and inter-domain etherification

The interlaminar toughening of a carbon fibre reinforced composite by interleaving a thin layer (~20 microns) of poly(hydroxyether of bisphenol A) (phenoxy) nanofibres was explored in this work. Nanofibres, free of defect and averaging several hundred nanometres, were produced by electrospinning directly onto a pre-impregnated carbon fibre material (Toray G83C) at various concentrations between 0.5 wt % and 2 wt %. During curing at 150 °C, phenoxy diffuses through the epoxy resin to form a semi interpenetrating network with an inverse phase type of morphology where the epoxy became the co-continuous phase with a nodular morphology. This type of morphology improved the fracture toughness in mode I (opening failure) and mode II (in-plane shear failure) by up to 150% and 30%, respectively. Interlaminar shear stress test results showed that the interleaving did not negatively affect the effective in-plane strength of the composites. Furthermore, there was some evidence from DMTA and FT-IR analysis to suggest that inter-domain etherification between the residual epoxide groups with the pendant hydroxyl groups of the phenoxy occurred, also leading to an increase in glass transition temperature (~7.5 °C).