Effect of heat-treatment atmosphere on the bond strength of apatite layer on Ti substrate

Objectives
The purpose of this study was to investigate the bond strength of apatite layer on titanium (Ti) substrate coated by biomimetic method and to improve the bonding of apatite layer to Ti substrate by optimizing the alkali heat-treatment process.

Methods
Ti plates pre-treated with an alkali solution of 10 M sodium hydroxide (NaOH) were heat-treated at 600 °C for 1 h at different atmospheres: in air and in vacuum. A dense apatite layer formed on top of the sodium titanate layer after soaking the alkali and heat-treated Ti samples in simulated body fluid (SBF) for up to 3 weeks. The bond strengths of the sodium titanate layer on Ti substrate, and apatite layer on the sodium titanate layer, were measured, respectively, by applying a tensile load. The fracture sites were observed with a scanning electron microscope (SEM).

Results
The apatite layer on the substrate after alkali heat-treatment in air achieved higher bond strength than that on the substrate after alkali heat-treatment in vacuum. It was found that the interfacial structure between the sodium titanate and Ti substrate has a significant influence on the bond strength of the apatite layer.

Significance
It is advised that titanium implants can achieve better osseointegration under load-bearing conditions by depositing an apatite layer in vivo on a Ti surface subjected to alkali and heat-treated in air.

Influence of deformation-induced heating on the bond strength of rolled metal multilayers

The bond strength of various metal multilayers produced by cold rolling of metal foils with different thermal conductivity was investigated. Results indicated that the metallic multilayer system with low thermal conductivity exhibited relative high bond strength while high thermal conductivity metal system may fail to be roll-bonded together. The relationship between the deformation-induced localized heating and the bond strength were discussed.

Effects of deformation-induced heating on bond strength of rolled metal multilayer

The bond strength of various metal multilayers produced by cold rolling of metal foils with different thermal conductivity was investigated. Results indicated that under the same conditions of deformation and surface preparation, the metallic multilayer system with low thermal conductivity exhibited relative high bond strength while high thermal conductivity metal system may fail to be roll-bonded together. The relationship between the deformation-induced localized heating and the bond strength were discussed. The deformation-induced localized heating in the low thermal conductivity metal multilayer systems may provide opportunities for achieving a successful accumulative roll bonding or a “cold roll/heat treatment/cold roll” process to synthesize metallic multilayer materials.

Assessment of bond strength in CFRP retrofitted beams under marine environment

Carbon fibre reinforced polymer (CFRP) sheet has gained its popularity to retrofit civil structures which is bonded externally, typically on the soffit of a beam. In this study, the bond between carbon fibre reinforced polymer (CFRP) and concrete is improved by modifying the property of commercial epoxy and compared against normal epoxy. The deterioration in bond strength was produced by placing the beam into salt water under wet dry cycles. Also, a model is proposed to determine the bond strength from flexural test and compared against the available bond strength models which are typically obtained from pull out test. This proposed model shows promising results in terms of predicting the bond strength from flexural test. In addition, a strength reduction factor is introduced to incorporate the effect of wet dry cycles to predict the long term behaviour. It is found that the modified epoxy enhance the ductile property and bond strength.

Improving bond strength for CFRP-RC beams interface

 Strengthened concrete structures using advanced materials such as CFRP composites has been proved an efficient technique. The bonding agent (epoxy resin) used to bond the CFRP composites with the concrete structures is the main parameter that contributes to premature failure. I was able to recommend to a new modified epoxy resin to enhance the general behavior of the strengthened concrete structure with respect to durability and ductility.

Lateral strength of zero bond masonry walls subjected to wind loads

Masonry walls are usually laid with the individual masonry units along a course overlapping units in the course below. Commonly, the perpend joints in the course occur above the mid-points of the units below to form a ‘half-bond’ or above a third point to form a ‘third-bond’. The amount of this overlap has a profound influence on the strength of a wall supported on three or four sides, where lateral pressures from wind cause combined vertical and horizontal flexure. Where masonry units are laid with mortar joints, the torsional shear bond resistance between the mortar and overlapping units largely determines the horizontal flexural strength. If there is zero bond strength between units, then the horizontal flexural strength is derived from the frictional resistance to torsion on the overlapping bed-faces of the units. This thesis reports a theoretical and experimental investigation into the frictional properties of overlapping units when subjected to combinations of vertical and horizontal moments and vertical axial compression. These basic properties were used to develop a theory to predict the lateral strength of walls supported on two, three or four sides. A plastic theory of behaviour was confirmed by experiment. The theory was then used to determine maximum unbraced panel sizes for particular boundary conditions. Design charts were developed to determine temporary bracing requirements for panels during construction.

Microstructures and bond strengths of the calcium phosphate coatings formed on titanium from different simulated body fluids

Calcium phosphate (Ca-P) coatings were deposited on Ti substrates by a biomimetic method from m-SBF and 10× SBF, respectively. Comparative study of microstructures and bond strengths of the Ca-P coatings deposited from those different SBFs was carried out. Effect of the surface roughness of the substrates on the bond strength of the Ca-P coatings was also studied. Scanning electron microscopy (SEM), X-ray diffractometry (XRD), Fourier transformed infrared spectroscopy (FTIR), inductive coupled plasma spectrometry (ICP) and thermogravimetry (TG) were used to characterize the Ca-P coatings. The bond strengths between the coatings and Ti substrates were measured using an adhesive strength test. Results indicated that the ionic concentrations of the SBFs and the surface roughness of the substrate had a significant influence on the formation, morphology and bond strength of the Ca-P precipitates. The induction period of time to deposit a complete Ca-P layer from the m-SBF is much longer, but the Ca-P coating is denser and has higher bond strength than that formed from the 10× SBF. The Ti with a surface roughness of R_a 0.64 µm and R_z 2.81 µm favoures the formation of a compact Ca-P coating from the m-SBF with the highest bond strength of approximately 15.5 MPa.

Melding: a new alternative to adhesive bonding

Melding, a novel method for joining composites is examined in this paper. The method uses Quickstep ™ technology to retain partially cured areas of a composite laminate, enabling subsequent bonding operations. The effect of melding on the mechanical properties of the composite has been investigated. Flexural testing of HexPly 914 indicates consistent properties throughout a melded section. Flexural strength values of 1.36±O.03 GPa compared to 1.35±O.03 GPa for a standard laminate were recorded. In order to achieve sufficient bond strength, the portion of the composite to be joined must have a significant proportion of uncured matrix. The ability of Hexply 914 prepreg to retain sufficient bonding potential to form a strong joint was also investigated. HexPly 914 Lap Shear results indicated no significant variation in strength values between co-cured and melded joins, with a recorded
strength value of 15.0±0. 7 MPa.

Biomimetic processing of nanocrystallite bioactive apatite coating on titanium-zirconium alloy

In this paper nanocrystallite apatite coating on TiZr substrate was prepared by a biomimetic process. Surface morphology, thickness, crystalline phases a~nd bond strength of the coating were investigated by SEM, XRD and tensIle test, respectively. Results show that the apatite coating exhibIts a nanocrystalIite structure with similar stoichiometry to that of natural bone. The apatite layer becomes thicker with the increasing of the SBF immersion time and is firmly adhered to the substrate with the highest average bond strength of 15.5 MPa. This nanocrystallite apatite coating is expected to bond to surrounding bone tissue directly in vivo after implantation.

Improved cathodic disbondment performance of polyethylene blends

Cathodic disbondment (CD) performance of a range of modified polyethylenes (PE) compression molded on to steel plates at 320[degrees]C is reported. Adhesion strength was measured by the 90[degrees] peel test and good dry adhesion strength was obtained for all modified polyethylene materials and blends, as well as for the neat polymer. It is shown that dry bond strength does not correlate with CD performance. Initial results of wet peel tests of samples in various concentrations of NaOH are presented where it is observed that for samples with improved wet adhesion strength, CD performance was also Improved. Surface polarity was determined from contact angle measurements, and it is shown that increased surface polarity of the coating was not the only determinant for improved CD performance. Inorganic fillers such as talc were also found to improve CD performance by changing the bulk properties, with little measurable change in polarity. Some mechanistic aspects of CD performance are also discussed.

A novel trust measurement method based on certified belief in strength for a multi-agent classifier system

A novel trust measurement method, namely, certified belief in strength (CBS), for a multi-agent classifier system (MACS) is proposed in this paper. The CBS method aims to improve the performance of the constituent agents of the MACS, viz., the fuzzy min-max (FMM) neural network classifier. Trust measurement is accomplished using reputation and strength of the constituent agents. Trust is built from strong elements that are associated with the FMM agents, allowing the CBS method to improve the performance of the MACS. An auction procedure based on the sealed bid, namely, the first price method, is adopted for the MACS in determining the winning agent. The effectiveness of the CBS method and the bond (based on trust) is verified by using a number of benchmark data sets. The results demonstrate that the proposed MACS-CBS model is able to produce better accuracy and stability as compared with those from other existing methods. © 2012 Springer-Verlag London.

Bioinspired strategy to reinforce PVA with improved toughness and thermal properties via hydrogen-bond self-assembly

Despite the high strength and stiffness of polymer nanocomposites, they usually display lower deformability and toughness relative to their matrices. Spider silk features exceptionally high stiffness and toughness via the hierarchical architecture based on hydrogen-bond (H-bond) assembly. Inspired by this intriguing phenomenon, we here exploit melamine (MA) to reinforce poly(vinyl alcohol) (PVA) via H-bond self-assembly at a molecular level. Our results have shown that due to the formation of physical cross-link network based on H-bond assembly between MA and PVA, yield strength, Young’s modulus, extensibility, and toughness of PVA are improved by 22, 25, 144, and 200% with 1.0 wt % MA, respectively. Moreover, presence of MA can enhance the thermal stability of PVA to a great extent, even exceeding some nanofillers (e.g., graphene). This work provides a facile method to improve the mechanical properties of polymers via H-bond self-assembly.

Bio-inspired hydrogen-bond cross-link strategy toward strong and tough polymeric materials

It remains a huge challenge to create advanced polymeric materials combining high strength, great toughness, and biodegradability so far. Despite enhanced strength and stiffness, biomimetic materials and polymer nanocomposites suffer notably reduced extensibility and toughness when compared to polymer bulk. Silk displays superior strength and toughness via hydrogen bonds (H-bonds) assembly, while cuticles of mussels gain high hardness and toughness via metal complexation cross-linking. Here, we propose a H-bonds cross-linking strategy that can simultaneously strikingly enhance strength, modulus, toughness, and hardness relative to polymer bulk. The H-bond cross-linked poly(vinyl alcohol) exhibits high yield strength (140 MPa), reduced modulus (22.5 GPa) in nanoindention tests, hardness (0.5 GPa), and great extensibility (40%). More importantly, there exist semiquantitive linear relationships between the number of effective H-bond and macroscale properties. This work suggests a promising methodology of designing advanced materials with exceptional mechanical by adding low amounts (1.0 wt %) of small molecules multiamines serving as H-bond cross-linkers.

Strength reduction in square columns confined with CFRP under marine environment

The performance of carbon fibre reinforced polymer (CFRP) wrapped square column under the wet/dry cycle of marine environment is studied in this paper. Two different types of epoxies (one commercial and one modified) are used to bond CFRP with concrete to investigate their suitability under the harsh environmental exposure. The experimental results are verified against the available theoretical models of square column and a reduction factor is derived to incorporate the effect of marine exposure to estimate the strength reduction for the columns in general. The accuracy of the proposed reduction factor is then verified by predicting the degraded strength of the columns which are currently available in the literature.