Heavy metal and microbial loads in sewage irrigated vegetables of Kabul, Afghanistan

Little is known about the heavy metal and microbial contamination of vegetables produced in Central Asian cities. We therefore measured the concentration of cadmium (Cd), copper (Cu), lead (Pb), and zinc (Zn) and of faecal pathogens (Coliform bacteria, Salmonella sp., Shigella sp., Ascaris lubricoides, Entamoeba sp. and pinworms [Oxyuris vermicularis syn. Enterobius vermicularis]) in soil, irrigation water, and marketed vegetables of Kabul City, Afghanistan. Leaf Pb and Zn concentrations of leafy vegetables were with 1–5 and 33–160 mg kg^{-1} dry weight (DW) several-fold above respective international thresholds of 0.3 mg Pb kg^{-1} and 50 mg Zn kg^{-1}. The tissue concentration of Cu was below threshold limits in all samples except for spinach in one farm. Above-threshold loads of microbes and parasites on vegetables were found in five out of six gardens with coliforms ranging from 0.5–2 × 10^7 cells 100g^{-1} fresh weight (FW), but no Salmonella and Shigella were found. Contamination with 0.2 × 10^7 eggs 100g^{-1} FW of Ascaris was detected on produce of three farms and critical concentrations of Entamoeba in a single case, while Oxyuris vermicularis, and Enterobius vermicularis were found on produce of three and four farms, respectively. Irrigation water had Ascaris, Coliforms, Salmonella, Shigella, Entamoeba, and Oxyuris vermicularis syn. Enterobius vermicularis ranging from 0.35 × 10^7 to 2 × 10^7 cells l^{-1}. The heavy metal and microbial loads on fresh UPA vegetables are likely the result of contamination from rising traffic, residues of the past decades of war and lacking treatment of sewage which needs urgent attention.

Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.