Rapid and efficient production of L-lactate from xylose using electrodialysis culture-associated product separation

L-Lactate was produced from xylose using electrodialysis culture (ED-C)-associated product separation. In a medium containing 50 g xylose/l, the ED-C was completed in only 32 h (i.e. less than half the time taken by the control culture, without electrodialysis). At 80 g xylose/l, the control culture was unable to consume more than 50 g xylose/1, whereas the ED-C showed increased xylose consumption and was completed by 45 h. The maximum rate of lactate production in the ED-C was higher than that in the control culture. ED-C was also carried out (at 80 g initial xylose/ l) with a supply of fresh xylose-free medium. This ED-C was completed within 30 h, which represents a reduction in fermentation time of 15 h when compared to ED-C without addition of xylose-free medium. Thus, rapid production of L-lactate was achieved by using ED-C which supplied fresh xylose-free medium.

Ethanol-induced water stress and fungal growth

Fungal growth inhibition by ethanol was compared with that caused by five other agents of water stress (at 25, 40 and 42.5°C), using Aspergillus oryzae. Ethanol, KCl, glycerol, glucose, sorbitol, and polyethylene glycol 400 were incorporated into media at concentrations corresponding to water activity (a(w)) values in the range 1 to 0.75. Generally, as temperature increased there was a decrease in the a(w) value at which optimum growth occurred. The a(w) limit for growth on KCl, glycerol, glucose, sorbitol, or polyethylene glycol 400 media was about 0.85, regardless of temperature. However, the a(w) limit for growth on ethanol media varied between 0.97 and 0.99 a(w) and was temperature-dependent. Water stress accounted for up to 31, 18 and 6% of growth inhibition by ethanol at 25, 40, and 42.5°C, respectively. For media containing ethanol, the decrease in growth rate per unit of a(w) reduction was greater as temperature increased. However, ethanol-induced water stress remained constant regardless of temperature, suggesting that other inhibitory effects of ethanol are closely temperature- dependent. Water stress may account for considerably more than 30% of growth inhibition by ethanol in cells that remain metabolically active at higher ethanol concentrations.

A rapid HPLC protocol for detection of polyols and trehalose

A procedure was developed to extract polyols and trehalose (protectants against stress) from fungal conidia. Conidia were sonicated (120 s) and immersed in a boiling water bath (5.5 min) to optimize extraction of polyols and trehalose, respectively. A rapid method was developed to separate and detect low-molecular-weight polyols and trehalose using high-performance liquid chromatography (HPLC). An ion exchange column designed for standard carbohydrate analysis was used in preference to one designed for sugar alcohol separation. This resulted in rapid elution (less than 5 min), without sacrificing peak resolution. The use of a pulsed electrochemical detector (gold electrode) resulted in limits of reliable quantification as low as 1.6 μg ml-1 for polyols and 2.8 μg ml-1 for trehalose. This is very sensitive and rapid method by which these protectants can be analysed. It avoids polyol derivatization that characterizes analysis by gas chromatography and the long run times (up to 45 min) that typify HPLC analysis using sugar alcohol columns.

Effects of KCl concentration on accumulation of acyclic sugar alcohols and trehalose in conidia of three entomopathogenic fungi

Beauveria bassiana, Metarhizium anisopliae and Paecilomyces farinosus were grown on Sabouraud Dextrose Agar (SDA) modified with KCl to give a range of water activity (a(w)) from 0.938 to 0.998. Growth of all three species was optimal at 0.983 a(w) and growth occurred over the a(w) range tested. Acyclic sugar alcohol (polyol) and trehalose content of conidia was determined by HPLC and found to vary with species and a(w). Conidia of B. bassiana and P. farinosus were found to contain totals of 1.5% and 2.3% polyols respectively at 0.998 a(w), and double these amounts at <0.950 a(w). Conidia of M. anisopliae contained from 5.7% to 6.8% polyols at each a(w) tested. In conidia of all three species the predominant polyol was mannitol. The lower molecular weight polyols, arabitol and erythritol, were found to accumulate at reduced a(w). Small amounts of glycerol were present in conidia of each species; <15% total polyols. Conidia of B. bassiana and M. anisopliae contained about 0.5% trehalose from 0.970 to 0.998 a(w), but only trace amounts below 0.950 a(w). Conidia of P. farinosus contained 2.1% trehalose at 0.998 a(w) and this decreased to <0.1% below 0.950 a(w). Potential to manipulate the endogenous reserves of conidia of these biological control agents to enhance viability and desiccation tolerance is discussed.

Novel monoclonal antibody and peptide binders for Mycobacterium avium subsp. paratuberculosis and their application for magnetic separation

The generation of novel Mycobacterium avium subsp. paratuberculosis (MAP)-specific monoclonal antibodies and phage-display derived peptide binders, along with their application for the magnetic separation (MS) of MAP cells, is described. Our aim was to achieve even greater MAP capture capability than is possible with peptide-mediated magnetic separation (PMS) using a 50:50 mix of biotinylated-aMp3 and biotinylated-aMptD peptide-coated beads. Gamma-irradiated whole MAP cells and ethanol extracted antigens (EEA) from these cells were used to elicit an immune response and as phage-display biopanning targets. A range of novel binders was obtained and coated onto paramagnetic beads, both individually and in various combinations, for MS evaluation. IS900 PCR was employed after MS to provide quick results. Capture sensitivity was assessed using a range of MAP concentrations after which the most promising beads were tested for their specificity for MAP, by performing MS followed by culture using 10 other Mycobacterium species. Magnetic beads coated with the biotinylated EEA402 peptide demonstrated a greater level of MAP capture than the current PMS method, even when low numbers of MAP (<10 cfu/ml) were present; however these beads also captured a range of other mycobacteria and so lacked capture specificity. Magnetic beads coated with monoclonal antibodies 6G11 and 15D10 (used as a 50:50 mix or as dually coated beads) also demonstrated improved MAP capture relative to the current PMS method, but with little cross-reactivity to other Mycobacterium spp. Therefore, two new MS protocols are suggested, the application of which would be dependent upon the required endpoint. Biotinylated EEA402-coated beads could potentially be used with a MAP-specific PCR to ensure detection specificity, while beads coated with 6G11 and 15D10 monoclonal antibodies could be used with culture or the phage amplification assay.