Arbuscular mycorrhizal fungal hyphae reduce soil erosion by surface water flow in a greenhouse experiment

The role of arbuscular mycorrhizal fungi (AMF) in resisting surface flow soil erosion has never been tested experimentally. We set up a full factorial greenhouse experiment using Achillea millefolium with treatments consisting of addition of AMF inoculum and non-microbial filtrate, non-AMF inoculum and microbial filtrate, AMF inoculum and microbial filtrate, and non-AMF inoculum and non-microbial filtrate (control) which were subjected to a constant shear stress in the form of surface water flow to quantify the soil detachment rate through time. We found that soil loss can be explained by the combined effect of roots and AMF extraradical hyphae and we could disentangle the unique effect of AMF hyphal length, which significantly reduced soil loss, highlighting their potential importance in riparian systems.

Analysis of friction factor reduction in turbulent water flow using a superhydrophobic coating

This study provides experimental and theoretical evidence that the coating of the inner surface of copper pipes with superhydrophobic (SH) materials induces a Cassie state flow regime on the flow of water. This results in an increase in the fluid's dimensionless velocity distribution coefficient, a, which gives rise to an increase in the apparent Reynolds number, which may approach the "plug flow state". Experimental evidence from the SH coating of a classic unsteady-state flow system resulted in a significant decrease in the friction factor and associated energy loss. The friction factor decrease can be attributed to an increase in the apparent Reynolds number. The study demonstrates that the Cassie effects imposed by SH coating can be quantitatively shown to decrease the frictional resistance to flow in commercial pipes.

Environmental Isotopes as Indicators for Ground Water Recharge to Fractured Granite

To assess the contribution of accumulated winter precipitation and glacial meltwater to the recharge of deep ground water flow systems in fracture crystalline rocks, measurements of environmental isotope ratios, hydrochemical composition, and in situ parameters of ground water were performed in a deep tunnel. The measurements demonstrate the significance of these ground water recharge components for deep ground water flow systems in fractured granites of a high alpine catchment in the Central Alps, Switzerland. Hydrochemical and in situ parameters, as well as d18O in ground water samples collected in the tunnel, show only small temporal variations. The precipitation record of d18O shows seasonal variations of ~14‰ and a decrease of 0.23‰ ± 0.03‰ per 100 m elevation gain. d2H and d18O in precipitation are well correlated and plot close to the meteoric water line, as well as d2H and d18O in ground water samples, reflecting the meteoric origin of the latter. The depletion of 18O in ground water compared to 18O content in precipitation during the ground water recharge period indicates significant contributions from accumulated depleted winter precipitation to ground water recharge. The hydrochemical composition of the encountered ground water, Na-Ca-HCO3-SO4(-F), reflects an evolution of the ground water along the flowpath through the granite body. Observed tritium concentrations in ground water range from 2.6 to 16.6 TU, with the lowest values associated with a local negative temperature anomaly and anomalous depleted 18O in ground water. This demonstrates the effect of local ground water recharge from meltwater of submodern glacial ice. Such localized recharge from glaciated areas occurs along preferential flowpaths within the granite body that are mainly controlled by observed hydraulic active shear fractures and cataclastic faults.

Gas-liquid two phase flow through a vertical 90deg elbow bend

Pressure drop data are reported for two phase air-water flow through a vertical to horizontal 90° elbow bend set in 0.026 m i.d. pipe. The pressure drop in the vertical inlet tangent showed some significant differences to that found for straight vertical pipe. This was caused by the elbow bend partially choking the inflow resulting in a build-up of pressure and liquid in the vertical inlet riser and differences in the structure of the flow regimes when compared to the straight vertical pipe. The horizontal outlet tangent by contrast gave data in general agreement with literature even to exhibiting a drag reduction region at low liquid rates and gas velocities between 1 and 2 m s -1. The elbow bend pressure drop was best correlated in terms of le/d determined using the actual pressure loss in the inlet vertical riser. The data showed a general increase with fluid rates that tapered off at high fluid rates and exhibited a negative pressure region at low rates. The latter was attributed to the flow being smoothly accommodated by the bend when it passed from slug flow in the riser to smooth stratified flow in the outlet tangent. A general correlation was presented for the elbow bend pressure drop in terms of total Reynolds numbers. A modified Lockhart-Martinelli model gave prediction of the data.

The influence of water motion on the growth rate of the kelp Laminaria hyperborea

The kelp Laminaria hyperborea is a dominant component of the subtidal nearshore ecosystem and is subjected to a heterogeneous wave and current climate. Water motion is known to influence physiological processes in macroalgae such as photosynthesis and nutrient uptake attributed to mass-transfer limitation. The study attempts to establish the effect of water motion on the growth rates of blades and elongation rates of the stipes of L. hyperborea at adjacent wave-exposed and wave-sheltered locations over a 12month period from field observations. The observations were supported by detailed physical and chemical measurements (light, temperature, seawater nutrient concentrations and hydrodynamics) and of tissue carbon and nitrogen concentrations together with δ¹³carbon. Despite a 30% difference in the root mean square of the velocity (Vel_rms) between the two survey locations, there was no evidence to suggest that water motion had any direct influence on the growth rates of either the blades or elongation of stipes of L. hyperborea. No significant differences were observed between either environmental or plant physiological variables between the sheltered and exposed locations. Using an integral velocity parameter (Vel_rms) the present study also highlighted the importance of the tidally induced current component of water flow in the subtidal zone. 

Anatomy and facies association of a drumlin in Co. Down, Northern Ireland, from seismic and electrical resistivity surveys

Seismic refraction and electrical resistivity geophysical techniques were used to reconstruct the internal architecture of a drumlin in Co. Down, Northern Ireland. Geophysical results were both validated and complemented by borehole drilling, ground water flow modelling, and geologic mapping. The geophysical anatomy of the drumlin consists of five successive layers with depth including; topsoil, partially saturated and saturated glacial tills, and weathered and more competent greywacke bedrock. There are numerous, often extensive inclusions of clay, sand, gravel, cobbles, and boulders within the topsoil and the till units. Together geophysical and geotechnical findings imply that the drumlin is part of the subglacial lodgement, melt-out, debris flow, sheet flow facies described by previous authors, and formed by re-sedimentation and streamlining of pre-existing sediments during deglaciation of the Late Devensian ice sheet. Seismic refraction imaging is particularly well suited to delineating layering within the drumlin, and is able to reconstruct depths to interfaces to within ± 0.5 m accuracy. Refraction imaging ascertained that the weathered bedrock layer is continuous and of substantial thickness, so that it acts as a basal aquifer which underdrains the bulk of the drumlin. Electrical resistivity imaging was found to be capable of delineating relative spatial changes in the moisture content of the till units, as well as mapping sedimentary inclusions within the till. The moisture content appeared to be elevated near the margins of the drumlin, which may infer a weakening of the drumlin slopes. Our findings advocate the use of seismic refraction and electrical resistivity methods in future sedimentological and geotechnical studies of internal drumlin architecture and drumlin formation, owing particularly to the superior, 3- D spatial coverage of these methods.

Comparative tracing experiments to investigate epikarst structural and compositional heterogeneity

Comparative tracer testing may be used to evaluate the vulnerability of groundwater to specific contaminants by comparing reactive tracer response to that of a simultaneously injected non-reactive “conservative” substance. Conversely, knowledge of tracer reaction with specific materials permits information about subsurface heterogeneity to be inferred. A series of tests completed in the vadose zone overlying a limestone aquifer employed a cocktail of particles along with reactive and non-reactive solute tracers to investigate transport rates between the ground surface and monitoring points approximately 10 m below ground. Short pulse tests revealed both solutes and particulate contaminants could travel at rates of over 10 m/h. Comparison of particle (microorganisms) and non-reactive solute tracer breakthrough revealed that particle tracers experience pore exclusion resulting in higher peak relative concentrations which arrive earlier than those of the solute. Prolonged tracer injection during subsequent experiments confirmed the response observed and illustrated that over 40 % of flow paths between injection and monitoring points were inaccessible to particles, but could allow solutes to pass through them. Similarly, the difference in response between various reactive tracers demonstrated tracers reached monitoring points via multiple flow paths and suggests geochemical heterogeneity plays an important role in influencing tracer behaviour. The results of this investigation highlight the complexity of water flow through the epikarst and the vulnerability of groundwater in karst aquifers to contamination when soil cover is thin to absent.

Measurement of permeability using a bench-top centrifuge

The commonly used British Standard constant head triaxial permeability test for testing of fine-grained soils is relatively time consuming. A reduction in the required time for soil permeability testing would provide potential cost savings to the construction industry, particularly in the construction quality assurance of landfill clay liners. The purpose of this paper is to evaluate an alternative approach of measuring permeability of fine-grained soils benefiting from accelerated time scaling for seepage flow when testing specimens in elevated gravity conditions provided by a centrifuge. As part of the investigation, an apparatus was designed and produced to measure water flow through soil samples under conditions of elevated gravitational acceleration using a small desktop laboratory centrifuge. A membrane was used to hydrostatically confine the test sample. A miniature data acquisition system was designed and incorporated in the apparatus to monitor and record changes in head and flow throughout the tests. Under enhanced gravity in the centrifuge, the flow through the sample was under ‘variable head' conditions as opposed to ‘constant head' conditions as in the classic constant head permeability tests conducted at 1 g . A mathematical model was developed for analysis of Darcy's coefficient of permeability under conditions of elevated gravitational acceleration and verified using the results obtained. The test data compare well with the results on analogous samples obtained using the classical British Standard constant head permeability tests.

Biomass-derived Oxymethylene Ethers as Diesel Additives: A Thermodynamic Analysis

Conversion of biomass for production of liquid fuels can help in reducing the greenhouse gas (GHG) emissions which are predominantly generated by combustion of fossil fuels. Adding oxymethylene ethers (OMEs) in conventional diesel fuel has the potential to reduce soot formation during the combustion in a diesel engine. OMEs are downstream products of syngas, which can be generated by the gasification of biomass. In this research, a thermodynamic analysis has been conducted through development of data intensive process models of all the unit operations involved in production of OMEs from biomass. Based on the developed model, the key process parameters affecting the OMEs production including equivalence ratio, H2/CO ratio, and extra water flow rate were identified. This was followed by development of an optimal process design for high OMEs production. It was found that for a fluidized bed gasifier with heat capacity of 28 MW, the conditions for highest OMEs production are at an air amount of 317 tonne/day, at H2/CO ratio of 2.1, and without extra water injection. At this level, the total OMEs production is 55 tonne/day (13 tonne/day OME3 and 9 tonne/day OME4). This model would further be used in a techno-economic assessment study of the whole biomass conversion chain to determine the most attractive pathways.

A multi-proxy chronological reconstruction of palaeosalinity in the eastern Limfjord, Denmark

The Jutland peninsula in northern Denmark is home to the Limfjord, one of the largest estuarine bodies of water in the region. Human inhabitance of the Limfjord’s surrounding coastlines stretches back further than 7,800 cal BP, with anthropogenic influence on the landscape beginning approximately 6,000 cal BP. Understanding how the Limfjord as a system has changed throughout time is useful in comprehending subsistence patterns and anthropogenic influence. This research is part of a larger project aimed at discerning subsistence patterns and environmental change in the region. Following the Younger Dryas, as the Fennoscandian ice sheet began to melt, Denmark experienced isostatic rebound, which contributed to the complex sea level history in the region. Between ice melt and isostatic rebound, the Jutland peninsula experienced many transgression and regression events. Connections to surrounding seas have shifted throughout time, with most attention focused on the western connection of the Limfjord with the North Sea, which has experienced numerous closures and subsequent re-openings throughout the Holocene. Furthermore, the Limfjord-North Sea connection has been the focal point of research because of the west to east water flow in the system, and the present day higher salinity in the west compared to the east. Little to no consideration has been paid to the influence of the Kattegat and Baltic on the Limfjord until now. A 10m sediment core was taken from Sebbersund (near Nibe, Limfjord), along the connection between the Limfjord and the Kattegat in the east to understand how the eastern part of the system has changed and differed from changes observed in the west. The Sebbersund sequence spans a majority of the Holocene, from 9600 cal BP to 1030 cal BP, determined via radiocarbon dating of terrestrial macrofossils and bulk sediment. Over this time period palaeoenvironmental conditions were reconstructed through the use of geochemical analyses (13C, 15N, C:N), physical sediment analyses, dinoflagellate cyst abundances and molluscan analyses. apart from two instances of low salinity, one at the top and one at the bottom of the core, the sequence has a strong marine signal for a majority of the Holocene. Radiocarbon dating of bulk sediment samples showed the presence of old carbon in the system, creating an age offset between 1,300 ± 200 and 2,800 ± 200 calibrated 14C years compared to the age-depth curve based on the terrestrial macrofossils. This finding, along with the strong marine influence in the system, discerned through geochemical data, dinoflagellate cyst and mollusc counts, is important for obtaining accurate radiocarbon ages in the region and stresses the importance of understanding both the marine and freshwater reservoir effects. The marine dominance in the eastern Limfjord differs from the west, which is characterized by a number of freshwater events when the North Sea connection was closed off during the Holocene. The eastern connection was open to the Kattegat throughout a large portion of the Holocene, with influx of open ocean water entering the system during periods of higher sea level.

Fluxes of organic contaminants from the river catchment into, through and out of the Humber Estuary, UK

This paper summarises the work done on the distribution and reactivity of organic contaminants (simazine, atrazine, lindane, fluoranthene, pyrene, PCB 77, PCB 118) in the Humber Estuary and associated major rivers, as part of the LOIS programme. The preliminary flux calculations show that the most important contributors of selected organic contaminants were the rivers Trent (45% of simazine, 20% of atrazine), Aire (30% of simazine and 33% of atrazine), Don (36 and 37% of fluoranthene and pyrene) and Ouse (18% of fluoranthene and pyrene). For lindane and PCBs, the Aire and Ouse were the key sources. The water flow in all the rivers shows strong seasonal variations, as do the contaminant concentrations. As a result, the mean daily fluxes of these contaminants displayed a strong seasonality. Annual mean concentrations of simazine and atrazine decreased by more than 50% over the period 1994-1995 in most of the rivers, probably as a result of their restricted use in the UK. Mass balance calculations show that the Humber is a sink for atrazine, lindane, PCB 77 and PCB 118, although the degree of removal is generally much lower for atrazine and lindane than for PCB 77 and PCB 118. Mass balance results also show that the Humber can either be a source of fluoranthene and pyrene (in the suspended particulate phase), or a sink (in the dissolved phase), although overall the Humber acts as sink. The budget exercise represents an attempt to quantify the input and output of selected organic contaminants from catchment to ocean. However, due to limited data and assumptions involved in calculations, the estimates should be considered as an order of magnitude approximation. Further improvement both in resolution and accuracy is required.