Contaminants in surface water and sediments around the Tynagh Mine, Galway, Ireland.

A former silver mine in Tynagh, Co. Galway, Ireland is one of the most contaminated mine sites in Europe with maximum concentrations of Zn, As, Pb, Mn, Ni, Cu, and Cd far exceeding guideline values for water and sediment. The aims of this research were to 1) further assess the contamination, particularly metals, in surface water and sediment around the site, and 2) determine if the contamination has increased 10 years after the Environmental Protection Agency Ireland (EPAI) identified off-site contamination. Site pH is alkaline to neutral because CaCO3-rich sediment and rock material buffer the exposed acid generating sulphide-rich ore. When this study was compared to the previous EPAI study conducted 10 years earlier, it appeared that further weathering of exposed surface sediment had increased concentrations of As and other potentially toxic elements. Water samples from the tailings ponds and adjacent Barnacullia Stream had concentrations of Al, Cd, Mn, Zn and Pb above guideline values. Lead and Zn concentrations from the tailings pond sediment were 16 and 5 times higher, respectively, than concentrations reported 10 years earlier. Pb and Zn levels in most sediment samples exceeded the Expert Group (EGS) guidelines of 1000 and 5000 mg/kg, respectively. Arsenic concentrations were as high as 6238 mg/kg in the tailings ponds sediment, which is 62 and 862 times greater than the EGS and Canadian Soil Quality Guidelines (CSQG), respectively. Cadmium, Cu, Fe, Mn, Pb and Zn concentrations in water and sediment were above guideline values downstream of the site. Additionally, Fe, Mn and organic matter (OM) were strongly correlated and correlated to Zn, Pb, As, Cd, Cu and Ni in stream sediment. Therefore, the nearby Barnacullia Stream is also a significant pathway for contaminant transport to downstream areas. Further rehabilitation of the site may decrease the contamination around the area.

Assessment of bioavailable arsenic and copper in soils and sediments from the Antofagasta region of northern Chile

Copper levels of nearly 500 mg l(-1) were measured in aqueous extracts of soil and sediment samples from the lowlands of Antofagasta. Arsenic levels of up to 183 mg l(-1) were found in river sediments, and 27.5 mg l(-1) arsenic was found at the location of a dam where potable water is extracted. This indicates that the arsenic contamination of water supplies reported recently for the pre-Andes may be a widespread problem throughout the region. Copper contamination from smelting activities also provides cause for concern as elevated levels were found in aqueous extracts of soil up to 20 km away from a smelter. This study went beyond traditional chemical analysis by assessing the potential benefits of using microbial biosensors as an alternative to determination of chemical speciation, to provide an environmentally relevant interpretation of soil/sediment residue levels. This approach is simple to use and enables a rapid, low cost assessment of pollutant bioavailability. It may, therefore, be of use for further investigations in the region and beyond.

Novel precipitated zirconia-based DGT technique for high-resolution imaging of oxyanions in waters and sediments

Water-sediment exchange is a fundamental component of oxyanion cycling in the environment. Yet, many of the (im)mobilization processes overlay complex spatial and temporal redox regimes that occur within millimeters of the interface. Only a few methods exist that can reliably capture these porewater fluxes, with the most popular being high-resolution diffusive gradients in thin films (HR-DGT). However, functionality of HR-DGT is restricted by the availability of suitable analyte binding agents within the sampler, which must be simple to cast and homogeneously distributed in the binding layer, exhibit adequate sorption capacities, be resistive to chemical change, and possess a very fine particle size (≤10 μm). A novel binding layer was synthesized to meet these requirements by in situ precipitation of zirconia into a precast hydrogel. The particle diameter ≤0.2 μm of zirconia in this precipitated gel was uniform and at least 50-times smaller than the conventional molding approach. Further, this gel had superior binding and stability characteristics compared with the commonly used ferrihydrite HR-DGT technique and could be easily fabricated as an ultrathin gel (60 μm) for simultaneous oxygen imaging in conjunction with planar-optodes. Chemical imaging of anion and oxygen fluxes using the new sampler were evaluated on Lake Taihu sediments.

Novel DGT method with tri-metal oxide adsorbent for in situ spatiotemporal flux measurement of fluoride in waters and sediments

Natural mineral-water interface reactions drive ecosystem/global fluoride (F−) cycling. These small-scale processes prove challenging to monitoring due to mobilization being highly localized and variable; influenced by changing climate, hydrology, dissolution chemistries and pedogenosis. These release events could be captured in situ by the passive sampling technique, diffusive gradients in thin-films (DGT), providing a cost-effective and time-integrated measurement of F− mobilization. However, attempts to develop the method for F− have been unsuccessful due to the very restrictive operational ranges that most F−-absorbents function within. A new hybrid-DGT technique for F− quantification containing a three-phase fine particle composite (Fesingle bondAlsingle bondCe, FAC) adsorbent was developed and evaluated. Sampler response was validated in laboratory and field deployments, passing solution chemistry QC within ionic strength and pH ranges of 0–200 mmol L−1 and 4.3–9.1, respectively, and exhibiting high sorption capacities (98 ± 8 μg cm−2). FAC-DGT measurements adequately predicted up to weeklong averaged in situ F− fluvial fluxes in a freshwater river and F− concentrations in a wastewater treatment flume determined by high frequency active sampling. While, millimetre-scale diffusive fluxes across the sediment-water interface were modeled for three contrasting lake bed sediments from a F−-enriched lake using the new FAC-DGT platform.

Isotopic assessment of sources and processes affecting sulfate and nitrate in surface water and groundwater of Luxembourg

Surface water and deep and shallow groundwater samples were taken from selected parts of the Grand-Duchy of Luxembourg to determine the isotopic composition of nitrate and sulfate, in order to identify sources and/or processes affecting these solutes. Deep groundwater had sulfate concentrations between 20 and 40 mg/L, d34Ssulfate values between -3.0 and -20.0‰, and d18Osulfate values between +1.5 and +5.0‰; nitrate was characterized by concentrations varying between

Mutual Solubilities of Water and Hydrophobic Ionic Liquids

The ionic nature of ionic liquids (ILs) results in a unique combination of intrinsic properties that produces increasing interest in the research of these fluids as environmentally friendly "neoteric" solvents. One of the main research fields is their exploitation as solvents for liquid-liquid extractions, but although ILs cannot vaporize leading to air pollution, they present non-negligible miscibility with water that may be the cause of some environmental aquatic risks. It is thus important to know the mutual solubilities between ILs and water before their industrial applications. In this work, the mutual solubilities of hydrophobic yet hygroscopic imidazolium-, pyridinium-, pyrrolidinium-, and piperidinium-based ILs in combination with the anions bis(trifluoromethylsulfonyl)imide, hexafluorophosphate, and tricyanomethane with water were measured between 288.15 and 318.15 K. The effect of the ILs structural combinations, as well as the influence of several factors, namely cation side alkyl chain length, the number of cation substitutions, the cation family, and the anion identity in these mutual solubilities are analyzed and discussed. The hydrophobicity of the anions increases in the order [C(CN)3] <[PF6] <[Tf2N] while the hydrophobicity of the cations increases from [Cnmim] <[Cnmpy] [Cnmpyr] <[Cnmpip] and with the alkyl chain length increase. From experimental measurements of the temperature dependence of ionic liquid solubilities in water, the thermodynamic molar functions of solution, such as Gibbs energy, enthalpy, and entropy at infinite dilution were determined, showing that the solubility of these ILs in water is entropically driven and that the anion solvation at the IL-rich phase controls their solubilities in water. The COSMO-RS, a predictive method based on unimolecular quantum chemistry calculations, was also evaluated for the description of the water-IL binary systems studied, where it showed to be capable of providing an acceptable qualitative agreement with the experimental data.

Mutual Solubilities of Water and the [Cnmim][Tf2N] Hydrophobic Ionic Liquids

Ionic liquids (ILs) have recently garnered increased attention because of their potential environmental benefits as "green" replacements over conventional volatile organic solvents. While ILs cannot significantly volatilize and contribute to air pollution, even the most hydrophobic ones present some miscibility with water posing environmental risks to the aquatic ecosystems. Thus, the knowledge of ILs toxicity and their water solubility must be assessed before an accurate judgment of their environmental benefits and prior to their industrial applications. In this work, the mutual solubilities for [C2-C8mim][Tf2N] (n-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide) and water between 288.15 and 318.15 K at atmospheric pressure were measured. Although these are among the most hydrophobic ionic liquids known, the solubility of water in these compounds is surprisingly large, ranging from 0.17 to 0.36 in mole fraction, while the solubility of these ILs in water is much lower ranging from 3.2 × 10-5 to 1.1 × 10-3 in mole fraction, in the temperature and pressure conditions studied. From the experimental data, the molar thermodynamic functions of solution and solvation such as Gibbs energy, enthalpy, and entropy at infinite dilution were estimated, showing that the solubility of these ILs in water is entropically driven. The predictive capability of COSMO-RS, a model based on unimolecular quantum chemistry calculations, was evaluated for the description of the binary systems investigated providing an acceptable agreement between the model predictions and the experimental data both with the temperature dependence and with the ILs structural variations.

Interfacial tensions of imidazolium-based ionic liquids with water and n-alkanes

The interfacial tension of the liquid-liquid phase boundary of several 1,3-dialkyl imidazolium based ionic liquids, namely, 1,3-dimethylimidazolium bis{(trifluoromethyl)sulfonyl}imide [C(1)mim][NTf2], 1-ethyl-3-methylimidazoliurn bis{(trifluoromethyl)sulfonyl}imide [C(2)mim][NTf2], 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide [C(4)mim][NTf2], 1-hexyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide [C(6)mim][NTf2], 1-octyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide [C(8)mim][NTf2], 1-butyl-3-methylimidazolium trifluoromethylsulfonate [C(4)mim][CF3SO3], and 1-butyl-3-methylimidazolium trifluoroacetate [C(4)mim][CF3COO] with water and with the n-alkanes, n-hexane, n-octane and n-decane, has been measured using the pendant drop method as a function of temperature from 293 to 323 K. The experimental interfacial tension data were correlated using the ionic liquid parachor estimation method and a mutual solubility model. The influence of the cation and anion of ionic liquids and also of alkyl chain length of n-alkanes on interfacial tension is discussed. It has also been demonstrated that the interfacial tension data estimated by the correlation methods are in good agreement with the experimental data. (C) 2010 Elsevier B.V. All rights reserved.

Physico-chemical properties of non-newtonian shear thickening diisopropyl-ethylammonium-based protic ionic liquids and their mixtures with water and acetonitrile

New protic ionic liquids (PILs) based on the diisopropyl-ethylammonium cation have been synthesized through a simple and atom-economic neutralization reaction between the diisopropyl-ethylamine and selected carboxylic acid. Densities and rheological properties were then measured for two original diisopropyl-ethylammonium-based protic ionic liquids (heptanoate and octanoate) at 298.15 K and atmospheric pressure. The effect of the presence of water or acetonitrile on the measured values was also examined over the whole composition range at 298.15 K and atmospheric pressure. From these values, excess properties were calculated and correlated by using a Redlich-Kister-type equation. Finally, a qualitative analysis of the evolution of studied properties with the alkyl chain length of the anion and with the presence or not of water (or acetonitrile) was performed. From this analysis, it appears that selected PILs and their mixtures with water or acetonitrile have a non-Newtonian shear thickening behavior, and the addition of water or acetonitrile on these PILs increases this phenomena by the formation of aggregates in these media.