Optimisation of granola breakfast cereal manufacturing process by wet granulation and pneumatic conveying

This study has considered the optimisation of granola breakfast cereal manufacturing processes by wet granulation and pneumatic conveying. Granola is an aggregated food product used as a breakfast cereal and in cereal bars. Processing of granola involves mixing the dry ingredients (typically oats, nuts, etc.) followed by the addition of a binder which can contain honey, water and/or oil. In this work, the design and operation of two parallel wet granulation processes to produce aggregate granola products were incorporated: a) a high shear mixing granulation process followed by drying/toasting in an oven. b) a continuous fluidised bed followed by drying/toasting in an oven. In high shear granulation the influence of process parameters on key granule aggregate quality attributes such as granule size distribution and textural properties of granola were investigated. The experimental results show that the impeller rotational speed is the single most important process parameter which influences granola physical and textural properties. After that binder addition rate and wet massing time also show significant impacts on granule properties. Increasing the impeller speed and wet massing time increases the median granule size while also presenting a positive correlation with density. The combination of high impeller speed and low binder addition rate resulted in granules with the highest levels of hardness and crispness. In the fluidised bed granulation process the effect of nozzle air pressure and binder spray rate on key aggregate quality attributes were studied. The experimental results show that a decrease in nozzle air pressure leads to larger in mean granule size. The combination of lowest nozzle air pressure and lowest binder spray rate results in granules with the highest levels of hardness and crispness. Overall, the high shear granulation process led to larger, denser, less porous and stronger (less likely to break) aggregates than the fluidised bed process. The study also examined the particle breakage of granola during pneumatic conveying produced by both the high shear granulation and the fluidised bed granulation process. Products were pneumatically conveyed in a purpose built conveying rig designed to mimic product conveying and packaging. Three different conveying rig configurations were employed; a straight pipe, a rig consisting two 45° bends and one with 90° bend. Particle breakage increases with applied pressure drop, and a 90° bend pipe results in more attrition for all conveying velocities relative to other pipe geometry. Additionally for the granules produced in the high shear granulator; those produced at the highest impeller speed, while being the largest also have the lowest levels of proportional breakage while smaller granules produced at the lowest impeller speed have the highest levels of breakage. This effect clearly shows the importance of shear history (during granule production) on breakage during subsequent processing. In terms of the fluidised bed granulation, there was no single operating parameter that was deemed to have a significant effect on breakage during subsequent conveying. Finally, a simple power law breakage model based on process input parameters was developed for both manufacturing processes. It was found suitable for predicting the breakage of granola breakfast cereal at various applied air velocities using a number of pipe configurations, taking into account shear histories.

Mathematical modelling and optimisation of the formulation and manufacture of aggregate food products

In this PhD study, mathematical modelling and optimisation of granola production has been carried out. Granola is an aggregated food product used in breakfast cereals and cereal bars. It is a baked crispy food product typically incorporating oats, other cereals and nuts bound together with a binder, such as honey, water and oil, to form a structured unit aggregate. In this work, the design and operation of two parallel processes to produce aggregate granola products were incorporated: i) a high shear mixing granulation stage (in a designated granulator) followed by drying/toasting in an oven. ii) a continuous fluidised bed followed by drying/toasting in an oven. In addition, the particle breakage of granola during pneumatic conveying produced by both a high shear granulator (HSG) and fluidised bed granulator (FBG) process were examined. Products were pneumatically conveyed in a purpose built conveying rig designed to mimic product conveying and packaging. Three different conveying rig configurations were employed; a straight pipe, a rig consisting two 45° bends and one with 90° bend. It was observed that the least amount of breakage occurred in the straight pipe while the most breakage occurred at 90° bend pipe. Moreover, lower levels of breakage were observed in two 45° bend pipe than the 90° bend vi pipe configuration. In general, increasing the impact angle increases the degree of breakage. Additionally for the granules produced in the HSG, those produced at 300 rpm have the lowest breakage rates while the granules produced at 150 rpm have the highest breakage rates. This effect clearly the importance of shear history (during granule production) on breakage rates during subsequent processing. In terms of the FBG there was no single operating parameter that was deemed to have a significant effect on breakage during subsequent conveying. A population balance model was developed to analyse the particle breakage occurring during pneumatic conveying. The population balance equations that govern this breakage process are solved using discretization. The Markov chain method was used for the solution of PBEs for this process. This study found that increasing the air velocity (by increasing the air pressure to the rig), results in increased breakage among granola aggregates. Furthermore, the analysis carried out in this work provides that a greater degree of breakage of granola aggregates occur in line with an increase in bend angle.

Enhancing the health-status of processed meats through ingredient manipulation and its effects on sensory and physiochemical product attributes

An important component of this Ph.D. thesis was to determine the European consumers’ views on processed meats and bioactive compounds. Thus a survey gathered information form over 500 respondents and explored their perceptions on the healthiness and purchase-ability for both traditional and functional processed meats. This study found that the consumer was distrustful towards processed meat, especially high salt and fat content. Consumers were found to be very pro-bioactive compounds in yogurt style products but unsure of their feelings on the idea of them in meat based products, which is likely due to the lack of familiarity to these products. The work in this thesis also centred on the applied acceptable reduction of salt and fat in terms of consumer sensory analysis. The products chosen ranged in the degree of comminution, from a coarse beef patty to a more fine emulsion style breakfast sausage and frankfurter. A full factorial design was implemented which saw the production of twenty beef patties with varying concentrations of fat (30%, 40%, 50%, 60% w/w) and salt (0.5%, 0.75%, 1.0%, 1.25%, 1.5% w/w). Twenty eight sausage were also produced with varying concentrations of fat (22.5%, 27.5%, 32.5%, 37.5% w/w) and salt (0.8%, 1%, 1.2%, 1.4%, 1.6%, 2%, 2.4% w/w). Finally, twenty different frankfurters formulations were produced with varying concentrations of fat (10%, 15%, 20%, 25% w/w) and salt (1%, 1.5%, 2%, 2.5%, 3% w/w). From these products it was found that the most consumer acceptable beef patty was that containing 40% fat with a salt level of 1%. This is a 20% decrease in fat and a 50% decrease in salt levels when compared to commercial patty available in Ireland and the UK. For sausages, salt reduced products were rated by the consumers as paler in colour, more tender and with greater meat flavour than higher salt containing products. The sausages containing 1.4 % and 1.0 % salt were significantly (P<0.01) found to be more acceptable to consumers than other salt levels. Frankfurter salt levels below 1.5% were shown to have a negative effect on consumer acceptability, with 2.5% salt concentration being the most accepted (P<0.001) by consumers. Samples containing less fat and salt were found to be tougher, less juicy and had greater cooking losses. Thus salt perception is very important for consumer acceptability, but fat levels can be potentially reduced without significantly affecting overall acceptability. Overall it can be summarised that the consumer acceptability of salt and fat reduced processed meats depends very much on the product and generalisations cannot be assumed. The study of bio-actives in processed meat products found that the reduced salt/fat patties fortified with CoQ10 were rated as more acceptable than commercially available products for beef patties. The reduced fat and salt, as well as the CoQ10 fortified, sausages were found to compare quite well to their commercial counterparts for overall acceptability, whereas commercial frankfurters were found to be the more favoured in comparison to reduced fat and CoQ10 fortified Frankfurters.

Micronutrient intakes and the role of nutritional supplements in the diets of Irish adults and pre-school children

To investigate micronutrient intakes and the role of nutritional supplements in the diets of Irish adults aged 18-64 years and pre-school children aged 1-4 years. Analysis is based on data from the National Adult Nutrition Survey (NANS) (n=1274) and the National Pre-School Nutrition Survey (NPNS) (n=500). Food and beverage intakes and nutritional supplement use were recorded using 4-day food records. Nutrients were estimated using WISP© which is based on McCance and Widdowson’s The Composition of Foods, 6thEd and the Irish Food Composition Database. “Meats”, “milk/yoghurt”, “breads”, “fruit/fruit juices” and “breakfast cereals” made important contributions to the intakes of a number of micronutrients. Micronutrient intakes were generally adequate, with the exception of iron (in adult females and 1 year olds) and vitamin D (in all population groups). For iron, zinc, copper and vitamin B6, up to 2% of adults had intakes that exceeded the upper limit (UL). Small proportions of children had intakes of zinc (11%), copper (2%), retinol (4%) and folic acid (5%) exceeding the UL. Nutritional supplements (predominantly multivitamin and/or mineral preparations) were consumed by 28% of adults and 20% of pre-school children. Among users, supplements were effective in reducing the % with inadequate intakes for vitamins A and D (both population groups) and iron (adult females only). Supplement users had a lower prevalence of inadequate intakes for vitamin A and iron compared to non-users. In adults only, users had a lower prevalence of inadequate intakes for magnesium, calcium and zinc, and displayed better compliance with dietary recommendations and lifestyle characteristics compared with non-users. There is poor compliance among women of childbearing age for the recommendation to take a supplement containing 400µg/day of folic acid. These findings are important for the development of nutrition policies and future recommendations for adults and pre-school children in Ireland and the EU.

National food consumption surveys: micronutrient intakes and the role of fortified foods in the diets of Irish pre-school children and adults

This research investigated the micronutrient intakes of Irish pre-school children (1-4 years) and adults (18-64 years) and the role that fortified foods (FFs) play in the diets of these population groups. Dietary intake data were collected as part of the National Pre-school Nutrition Survey (NPNS) (2010-2011) and the National Adult Nutrition Survey (NANS) (2008-2010) using 4-day food and beverage records. Nutrient intakes were estimated using WISP©, which encompasses McCance and Widdowson’s The Composition of Foods and the Irish Food Composition Database. A FF is one in which one or more micronutrients are added. Key dietary sources of micronutrients in NPNS and NANS were “milk”, “meat & meat products”, “breakfast cereals”, “fruit & fruit juices” and “breads”. In general, intakes of most micronutrients were adequate with the exception of iron (1 year old children and adult women) and vitamin D (in all population groups). Small proportions of the pre-school population had intakes which exceeded the upper level (UL) (zinc: 11%, folic acid: 5%, retinol: 4%, copper: 2%). Less than 2% of adults had intakes of iron, copper, zinc and vitamin B6 which exceeded the UL. FFs were consumed by 97% of pre-school children and 82% of adults, representing 17% and 9% of mean daily energy intake respectively. Relative to energy intake, FFs contributed substantially greater proportions to intakes of key micronutrients, such as iron and vitamin D. FFs were effective in reducing the prevalence of inadequate micronutrient intakes in these population groups, particularly for iron in women and 1 year old children. FFs made a significant contribution to folate intake in women of childbearing age (72µg). FFs contributed greater proportions of carbohydrate and lower proportions of fat to the diets of consumers. Voluntary addition of nutrients to foods did not contribute appreciably to intakes exceeding the UL in these population groups.

Tooth wear in Irish teenagers: a laboratory and epidemiological study

Aim: To investigate the characteristics, development and determinants of toothwear among Irish schoolchildren. Methods: A cross-sectional (examination at 16-years-old) and longitudinal (examinations at 5-,12-,14-years) study were conducted. Two indices were used to measure toothwear, children/parents completed a demographic profile and questionnaire on oral hygiene and dietary practices, health, and lifestyle in both studies. Saliva was collected from consenting 16-year-olds. The explanatory variables for the cross-sectional and longitudinal study were derived from children/parents responses. Differences in salivary profiles were determined for subsets; the protein concentration was determined with Bradford protein assay and protein carbonyl concentration (a protein oxidation marker) was determined spectrophotometrically. Gel-electrophoresis and mass spectrometry determined proteins and ion chromatography inorganic ions. Statistical significance was accepted at p<0.05. Results: At 16-years-old the prevalence of toothwear with dentine visible was 44%. No difference in salivary flow rates existed. In unstimulated saliva a higher mean, protein carbonyl (p<0.0001) and total calcium concentration (p<0.002) existed for the group with moderate toothwear. In stimulated saliva the moderate toothwear group had a lower mean protein concentration(p<0.0001). The 2-DE protein spots prepared for a sub-group differed between those with toothwear and without. Mass spectrometry, identified one of the different proteins as IgA. For 16-year-olds, the self-reported factors indicated that brushing after breakfast was associated with lower toothwear scores(p<0.03). Nail-biting, being asthmatic or reporting a dry mouth were associated with higher toothwear scores(all p<0.05). Eating an apple daily or less was associated with less toothwear(p<0.002). In the longitudinal study toothwear into dentine at age five or 12-years was associated with more toothwear at age 14(all p<0.05). Discussion: The results illustrate the multifactorial aetiology of toothwear. The biochemical and physical correlates of saliva with toothwear requires further research. Conclusion: The impact of previous toothwear, salivary, dietary and personal factors on toothwear in the early permanent dentition is demonstrated.