Particulate composite based on coconut fiber and castor oil polyurethane adhesive: An eco-efficient product

This paper presents a study on the potential use of coconut fiber as material to produce particleboards, with two different densities (0.8 g/cm(3) and 1.0 g/cm3), using castor oil-based polyurethane adhesive and urea-formaldehyde. The quality of the product that can be produced by industry was evaluated according to the normative NBR 14.810:2006, where density, thickness swell (TS), absorption, modulus of elasticity (MOE), modulus of rupture (MOR) in static bending and internal bond (IB) were determined. From the results, there was a decrease in TS and increase in MOR of coconut fiber panels with polyurethane resin panels compared with coconut fiber and resin urea-formaldehyde. Scanning microscopy electronic images (SEM) indicated that castor oil-based polyurethane adhesive occupies the gaps between the particles, a factor that contributes to improved physical and mechanical properties of the panels. The assessment of durability through accelerated aging tests shows that panels protected with waterproofing material can be used in environments that have contact with moisture. (C) 2012 Elsevier B.V. All rights reserved.

Status of Aceria guerreronis Keifer (Acari: Eriophyidae) as a Pest of Coconut in the State of Sao Paulo, Southeastern Brazil

The coconut mite, Aceria guerreronis Keifer, is one of the main pests of coconut palms (Cocos nucifera) in northeastern Brazil. The objective of this study was to evaluate the levels of the coconut mite and other mites on coconut palms in the state of So Paulo and to estimate the possible role of predatory mites in the control of this pest. The effect of cultivated genotypes and sampling dates on the mite populations was also estimated. We sampled attached fruits, leaflets, inflorescences, and fallen fruits. The coconut mite was the main phytophagous mite found on attached and fallen fruits, with average densities of 110.0 and 20.5 mites per fruit, respectively. The prevalent predatory mites on attached and fallen fruits were Proctolaelaps bulbosus Moraes, Reis & Gondim Jr. and Proctolaelaps bickleyi (Bram), both Melicharidae. On leaflets, the tenuipalpids Brevipalpus phoenicis (Geijsks) and Tenuipalpus coyacus De Leon and the tetranychid Oligonychus modestus (Banks) were the predominant phytophagous mites. On both leaflets and inflorescences, the predominant predatory mites belonged to the Phytoseiidae. Neoseiulus baraki (Athias-Henriot) and Neoseiulus paspalivorus (De Leon), predators widely associated with the coconut mite in northeastern Brazil and several other countries, were not found. The low densities of the coconut mite in So Paulo could be related to prevailing climatic conditions, scarcity of coconut plantations (hampering the dispersion of the coconut mite between fields), and to the fact that some of the genotypes cultivated in the region are unfavorable for its development.

Dispersal strategies of Aceria guerreronis (Acari: Eriophyidae), a coconut pest

The dispersal of plant-feeding mites can occur involuntarily, through transportation of infested plant parts, or voluntarily, by walking to new plant parts or to suitable spots where biotic (phoresis) or abiotic (wind, agricultural tools, etc.) factors carry them over long distances. Elucidating the dispersal mechanisms of the coconut mite, Aceria guerreronis Keifer, is important for understanding the process of colonization of new fruits of a same or different plants, essential for the improvement of control strategies of this serious coconut pest. Thus, the objective of this work was to investigate the voluntary dispersal mechanisms of this mite. The hypothesis that the coconut mite disperses by walking, phoresis or wind were tested. The coconut mite was shown to be able to walk short distances between fruits of the same bunch or between bunches of the same plant. Phoresis on insects of the orders Hymenoptera (Apidae), Coleoptera (Curculionidae) and Lepidoptera (Phycitidae) was evaluated in the laboratory and in the field. Although in the laboratory mites were shown to be able to climb onto honeybees, field investigations failed to show these insects as important carriers of the pest, corroborating findings of previous works; however, both laboratory and field investigations suggested the curculionid Parisoschoenus obesulus Casey to be able to transport the coconut mite between plants. Similarly, laboratory and field investigations suggested wind to be important in the dispersal of the coconut mite between plants.

Morphological, molecular and cross-breeding analysis of geographic populations of coconut-mite associated predatory mites identified as Neoseiulus baraki: evidence for cryptic species?

Surveys were conducted in Brazil, Benin and Tanzania to collect predatory mites as candidates for control of the coconut mite Aceria guerreronis Keifer, a serious pest of coconut fruits. At all locations surveyed, one of the most dominant predators on infested coconut fruits was identified as Neoseiulus baraki Athias-Henriot, based on morphological similarity with regard to taxonomically relevant characters. However, scrutiny of our own and published descriptions suggests that consistent morphological differences may exist between the Benin population and those from the other geographic origins. In this study, we combined three methods to assess whether these populations belong to one species or a few distinct, yet closely related species. First, multivariate analysis of 32 morphological characters showed that the Benin population differed from the other three populations. Second, DNA sequence analysis based on the mitochondrial cytochrome oxidase subunit I (COI) showed the same difference between these populations. Third, cross-breeding between populations was unsuccessful in all combinations. These data provide evidence for the existence of cryptic species. Subsequent morphological research showed that the Benin population can be distinguished from the others by a new character (not included in the multivariate analysis), viz. the number of teeth on the fixed digit of the female chelicera.

Chemical Interesterification of Blends of Palm Stearin, Coconut Oil, and Canola Oil: Physicochemical Properties

trans-Free interesterified fat was produced for possible usage as a margarine. Palm stearin, coconut oil, and canola oil were used as substrates for chemical interesterification. The main aim of the present study was to evaluate the physicochemical properties of blends of palm stearin, coconut oil, and canola oil submitted to chemical interesterification using sodium methoxide as the catalyst. The original and interesterified blends were examined for fatty acid composition, softening and melting points, solid fat content, and consistency. Chemical interesterification reduced softening and melting points, consistency, and solid fat content. The interesterified fats showed desirable physicochemical properties for possible use as a margarine. Therefore, our result suggested that the interesterified fat without trans-fatty acids could be used as an alternative to partially hydrogenated fat.

Study of adsorption isotherms of green coconut pulp

Brazil is considered one of the largest producers and consumers of tropical fruits. Green coconut (Cocos nucifera L.) stands out not only for its production and consumption, but also for the high amount of waste produced by coconut water industry and in natura consumption. Therefore, there is a need for utilization of this by-product. This study aims to study the adsorption isotherms of green coconut pulp and determine its isosteric heat of sorption. The adsorption isotherms at temperatures of 30, 40, 50, 60, and 70 °C were analyzed, and they exhibit type III behavior, typical of sugar rich foods. The experimental results of equilibrium moisture content were correlated by models present in the literature. The Guggenheim, Anderson and De Boer (GAB) model proved particularly good overall agreement with the experimental data. The heat of sorption determined from the adsorption isotherms increased with the decrease in moisture content. The heat of sorption is considered as indicative of intermolecular attractive forces between the sorption sites and water vapor, which is an important factor to predict the shelf life of dried products.

Sensitivity of Eisenia andrei (Annelida, Oligochaeta) to a commercial formulation of abamectin in avoidance tests with artificial substrate and natural soil under tropical conditions

Obtaining ecotoxicological data on pesticides in tropical regions is imperative for performing more realistic risk analysis, and avoidance tests have been proposed as a useful, fast and cost-effective tool. Therefore, the present study aimed to evaluate the avoidance behavior of Eisenia andrei to a formulated product, Vertimec(A (R)) 18 EC (a.i abamectin), in tests performed on a reference tropical artificial soil (TAS), to derive ecotoxicological data on tropical conditions, and a natural soil (NS), simulating crop field conditions. In TAS tests an adaptation of the substrate recommended by OECD and ISO protocols was used, with residues of coconut fiber as a source of organic matter. Concentrations of the pesticide on TAS test ranged from 0 to 7 mg abamectin/kg (dry weight-d.w.). In NS tests, earthworms were exposed to samples of soils sprayed in situ with: 0.9 L of Vertimec(A (R)) 18 EC/ha (RD); twice as much this dosage (2RD); and distilled water (Control), respectively, and to 2RD: control dilutions (12.5, 25, 50, 75%). All tests were performed under 25 +/- A 2A degrees C, to simulate tropical conditions, and a 12hL:12hD photoperiod. The organisms avoided contaminated TAS for an EC50,48h = 3.918 mg/kg soil d.w., LOEC = 1.75 mg/kg soil d.w. and NOEC = 0.85 mg/kg soil d.w. No significant avoidance response occurred for any NS test. Abamectin concentrations in NS were rather lower than EC50, 48h and LOEC determined in TAS tests. The results obtained contribute to overcome a lack of ecotoxicological data on pesticides under tropical conditions, but more tests with different soil invertebrates are needed to improve pesticides risk analysis.

Edible films from alginate-acerola puree reinforced with cellulose whiskers

Fruit purees, combined or not with polysaccharides, have been used in some studies to elaborate edible films. The present study was conducted to evaluate tensile properties and water vapor barrier of alginate-acerola puree films plasticized with corn syrup, and to study the influence of cellulose whiskers from different origins (cotton fiber or coconut husk fiber, the latter submitted to one- or multi-stage bleaching) on the film properties. The whiskers improved the overall tensile properties (except by elongation) and the water vapor barrier of the films. The films with coconut whiskers, even those submitted only to a one-stage bleaching, presented similar properties to those of films with cotton whiskers, despite the low compatibility between the matrix and the remaining lignin in coconut whiskers. This was probably ascribed to a counterbalancing effect of the higher aspect ratios of the coconut whiskers. (C) 2011 Elsevier Ltd. All rights reserved.

Continuous enzymatic interesterification of lard and soybean oil blend: Effects of different flow rates on physical properties and acyl migration

Continuous enzymatic interesterification is an alternative to chemical interesterification for lipid modification technology which is economically viable for large scale use. A blend of 70% lard and 30% soybean oil was submitted to continuous enzymatic interesterification in a glass tubular bioreactor at flow rate ranging from 0.5 to 4.5 mL/min. The original mixture and the reaction products obtained were examined to determine melting and crystallization behavior by DSC, and analyzed for regiospecific fatty acid distribution. Continuous enzymatic interesterification changed the mixture, forming a new triacylglycerol composition, verified by DSC curves and variation in enthalpy of melting values. The regiospecific distribution of fatty acids was changed by flow variations in the reactor. In the continuous enzymatic interesterification reaction the flow rate of 4.5 mL/min, was more advantageous than slower flow rates, reducing acyl migration and increasing process productivity. (C) 2011 Elsevier B.V. All rights reserved.

Limitations of Neoseiulus baraki and Proctolaelaps bickleyi as control agents of Aceria guerreronis

Several predatory mites have been found in association with the coconut mite, Aceria guerreronis Keifer, in northeast Brazil. However, the latter still causes damage to coconut in that region. The objectives of this work were to compare the frequencies of occurrence of Neoseiulus (Phytoseiidae) and Proctolaelaps (Melicharidae) species on standing and aborted coconuts in coastal Pernambuco State, northeast Brazil and to analyze their possible limitations as control agents of the coconut mite, based on evaluations of the restrictions they may have to access the microhabitat inhabited by the pest and their functional and reproductive responses to increasing densities of the latter. Neoseiulus baraki (Athias-Henriot) was found mostly on standing coconuts whereas Proctolaelaps bickleyi (Bram) was found mostly on aborted coconuts. Measurements of the entrance to the microhabitat occupied by the coconut mite, between the bracts and the subjacent fruit surface, showed that this different pattern of predator prevalence could be related to predator sizes, although other environmental factors could not be disregarded. Progressively higher predation rate of N. baraki was observed up to an experimental density that corresponded to 1,200 coconut mites per fruit, which is close to the average number determined in northeast Brazil, reducing slightly afterwards. Predation rate of P. bickleyi reduced consistently but slightly with increasing prey densities, but in absolute values, rates were always much higher than determined for N. baraki. The excessively high killing capacity of P. bickleyi, probably related to its high feeding requirement, may be detrimental in terms of stability. In fact, such high requirement for food suggests that P. bickleyi might not have a strong relation with the coconut mite and that the latter may not be its main food source under natural conditions. It is concluded that body sizes of both predators and the exceedingly high feeding requirement of P. bickleyi may limit their performance as control agents of the coconut mite.

Can the red palm mite threaten the Amazon vegetation?

The red palm mite Raoiella indica Hirst (Tenuipalpidae) was first reported in the New World in 2004, dispersing quickly and widely while adopting new plant species as hosts. Since then, it has caused severe damage in this region, especially to coconut (Cocos nucifera L.). It was first found in Brazil in 2009, in the northern Amazonian state of Roraima. In the present study, native and introduced plants were sampled between March 2010 and February 2011 in sites of the 15 Roraima municipalities, to estimate its distribution and the associated mite fauna. In addition, monthly samples were taken from a coconut plantation in Mucajai throughout the same period, for an initial appraisal of the levels R. indica could reach. It was found in 10 municipalities, on 19 plant species of four families. Six species are reported for the first time as hosts. Among the associated predators, 89.1% were Phytoseiidae, most commonly Amblyseius largoensis (Muma), Iphiseiodes zuluagai Denmark & Muma and Euseius concordis (Chant). The highest densities of R. indica, 1.5 and 0.35 mites/cm2 of leaflet (approx total of 331 and 77 mites/leaflet), were reached respectively in March 2010 and February 2011. The highest density of phytoseiids on coconut (0.009 mites/cm2 or about 2 mites/leaflet) was reached in November 2010. The average densities of R. indica recorded for Roraima were comparable to those reported for countries in which the mite is reportedly economically damaging. The dispersal of R. indica through the Amazon forest may result in damage to cultivated and native palms, and plants of other families, if the projected increase in both the frequency and the severity of drought events occurs. Parts of the Amazon have undergone periods of low rainfall, a condition that appears to favour the biology of this mite. Its eventual arrival to northeastern Brazil may result in heavy economic and ecological losses.

Ascensão capilar de água em substratos de coco e de pinus

O uso da irrigação por capilaridade na produção de mudas em viveiros pode trazer vantagens ao uso de água e sua utilização adequada requer o conhecimento da capacidade de ascensão de água no meio de crescimento das raízes, atributo pouco estudado. Para avaliar esta condição fundamental, este trabalho tem como objetivo avaliar a ascensão de água em substratos comerciais de coco e pinus, em dois padrões de tamanho de partículas e em duas condições de umidade, para indicar aquele que possua as melhores características físicas para aplicação na irrigação por capilaridade. Utilizou-se o método de ascensão capilar, com colunas desmontáveis de anéis preenchidas com substratos, avaliando-se os seguintes tempos de contato do fundo da coluna com a lâmina de água: 0,25, 0,5, 1, 2, 4, 8, 16 e 24 horas, com 10 repetições por tempo testado. Pelos resultados, observou-se que a maior ascensão capilar acumulada em 24 horas de ensaio foi obtida para os substratos de textura fina de coco e de pinus. Além disso, a hidrofobia do substrato de coco seco recomenda que as irrigações nesse material devem ter frequências maiores que substratos de pinus, evitando seu secamento. O substrato de pinus, por não apresentar esse comportamento, deve ter turnos de rega mais espaçados, principalmente sob textura fina. Devido à sua maior retenção de água e capacidade de elevação de água quando umedecido, o substrato fino de coco é mais adequado à irrigação por capilaridade em recipientes como tubetes.

Dinâmica do potencial matricial em substratos de pinus e coco sob ação da capilaridade

O tamanho médio de partículas e a porosidade dos substratos condicionam as propriedades matriciais, interferindo na capacidade de retenção e de transmissão da água no meio. O conhecimento desses atributos é fundamental em processos de irrigação por capilaridade, para que o molhamento atinja as camadas superiores dos recipientes com níveis de tensão de água facilmente disponível. O presente trabalho teve como objetivo estudar a ascensão de água por capilaridade para determinar a posição mais apropriada do nível de saturação na ascensão capilar em recipientes com substratos de coco e pinus, de textura grossa e fina. Foram efetuados experimentos avaliando a ascensão de água por capilaridade em colunas segmentadas preenchidas com os substratos. Os valores de umidade em cada segmento foram calculados gravimetricamente e relacionados aos de tensão estimados pela curva de tensão dos substratos. Os substratos com textura fina apresentaram melhor elevação de água por capilaridade, com melhor elevação da umidade em níveis de tensão de água disponível. O substrato de coco fino apresentou água disponível em todo o perfil do recipiente, enquanto o de pinus apresentou as camadas superiores do recipiente com água retida em tensões abaixo do ponto de murcha permanente. O substrato fino de coco apresentou os melhores resultados para aplicação na irrigação por capilaridade, permitindo recomendar o seu uso com o nível de saturação posicionado a cinco centímetros do fundo do recipiente por quinze minutos.