Low-density koala (Phascolarctos cinereus) populations in the mulgalands of south-west Queensland. IV. Abundance and conservation status

Urban encroachment on dense, coastal koala populations has ensured that their management has received increasing government and public attention. The recently developed National Koala Conservation Strategy calls for maintenance of viable populations in the wild. Yet the success of this, and other, conservation initiatives is hampered by lack of reliable and generally accepted national and regional population estimates. In this paper we address this problem in a potentially large, but poorly studied, regional population in the State that is likely to have the largest wild populations. We draw on findings from previous reports in this series and apply the faecal standing-crop method (FSCM) to derive a regional estimate of more than 59 000 individuals. Validation trials in riverine communities showed that estimates of animal density obtained from the FSCM and direct observation were in close agreement. Bootstrapping and Monte Carlo simulations were used to obtain variance estimates for our population estimates in different vegetation associations across the region. The most favoured habitat was riverine vegetation, which covered only 0.9% of the region but supported 45% of the koalas. We also estimated that between 1969 and 1995 -30% of the native vegetation associations that are considered as potential koala habitat were cleared, leading to a decline of perhaps 10% in koala numbers. Management of this large regional population has significant implications for the national conservation of the species: the continued viability of this population is critically dependent on the retention and management of riverine and residual vegetation communities, and future vegetation-management guidelines should be cognisant of the potential impacts of clearing even small areas of critical habitat. We also highlight eight management implications.

Using simulation techniques to investigate methods to determine resistance of helminths to anthelmintic treatment

The widespread and increasing resistance of internal parasites to anthelmintic control is a serious problem for the Australian sheep and wool industry. As part of control programmes, laboratories use the Faecal Egg Count Reduction Test (FECRT) to determine resistance to anthelmintics. It is important to have confidence in the measure of resistance, not only for the producer planning a drenching programme but also for companies investigating the efficacy of their products. The determination of resistance and corresponding confidence limits as given in anthelmintic efficacy guidelines of the Standing Committee on Agriculture (SCA) is based on a number of assumptions. This study evaluated the appropriateness of these assumptions for typical data and compared the effectiveness of the standard FECRT procedure with the effectiveness of alternative procedures. Several sets of historical experimental data from sheep and goats were analysed to determine that a negative binomial distribution was a more appropriate distribution to describe pre-treatment helminth egg counts in faeces than a normal distribution. Simulated egg counts for control animals were generated stochastically from negative binomial distributions and those for treated animals from negative binomial and binomial distributions. Three methods for determining resistance when percent reduction is based on arithmetic means were applied. The first was that advocated in the SCA guidelines, the second similar to the first but basing the variance estimates on negative binomial distributions, and the third using Wadley’s method with the distribution of the response variate assumed negative binomial and a logit link transformation. These were also compared with a fourth method recommended by the International Co-operation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal Products (VICH) programme, in which percent reduction is based on the geometric means. A wide selection of parameters was investigated and for each set 1000 simulations run. Percent reduction and confidence limits were then calculated for the methods, together with the number of times in each set of 1000 simulations the theoretical percent reduction fell within the estimated confidence limits and the number of times resistance would have been said to occur. These simulations provide the basis for setting conditions under which the methods could be recommended. The authors show that given the distribution of helminth egg counts found in Queensland flocks, the method based on arithmetic not geometric means should be used and suggest that resistance be redefined as occurring when the upper level of percent reduction is less than 95%. At least ten animals per group are required in most circumstances, though even 20 may be insufficient where effectiveness of the product is close to the cut off point for defining resistance.

Predicting wood value in Queensland Caribbean pine plantations using a decision support system

A decision support system has been developed in Queensland to evaluate how changes in silvicultural regimes affect wood quality, and specifically the graded recovery of structural timber. Models of tree growth, branch architecture and wood properties were developed from data collected in routine Caribbean pine plantations and specific silvicultural experiments. These models were incorporated in software that simulates the conversion of standing trees into logs, and the logs into boards, and generates detailed data on knot location and basic density distribution. The structural grade of each board was determined by simulating the machine stress-grading process, and the predicted graded recovery provided an indicator of wood value. The decision support system improves the basis of decision-making by simulating the performance of elite genetic material under specified silvicultural regimes and by predicting links between wood quality and general stand attributes such as stocking and length of rotation.

Helicoverpa armigera (Hubner): can wheat stubble protect cotton plants against attack?

When investigating strategies for Helicoverpa armigera (Hubner) control, it is important to understand oviposition behaviour. Cotton (Gossypium hirsutum) was sown into standing wheat (Triticum astivum L.) stubble in a closed arena to investigate the effect of stubble on H. armigera moth behaviour and oviposition. Infrared cameras were used to track moths and determine whether stubble acted as a physical barrier or provided camouflage to cotton plants, thereby reducing oviposition. Searching activity was observed to peak shortly before dawn (03:00 and 04:00 h) and remained high until just after dawn (4 h window). Moths spent more time resting on cotton plants than spiralling above them, and the least time flying across the arena. While female moths spent more time searching for cotton plants growing in wheat stubble, the difference in oviposition was not significant. As similar numbers of eggs were laid on cotton plants with stubble (3.5/plant SE +/- 0.87) and without stubble (2.5/plant SE +/- 0.91), wheat stubble does not appear to provide camouflage to cotton plants. There was no significant difference in the location of eggs deposited on cotton plants with and without stubble, although more eggs were laid on the tops of cotton leaves in wheat stubble. As the spatial and temporal distribution of eggs laid on the cotton plant is a crucial component of population stability, eggs laid on the upper side of leaves on cotton plants may be more prone to fatalities caused by environmental factors such as wind and rain. Therefore, although stubble did not influence the number of eggs laid, it did affect their distribution on the plant, which may result in increased mortality of eggs on cotton plants sown into standing wheat stubble.

Spatial requirements of animals: Allometry and beyond

Space allowance is a major factor influencing animal welfare. For livestock, at least, it plays a critical role in profitability, yet there is little information on the amount of space that animals require. The amount of space an animal occupies as a consequence of its shape and size can be estimated using allometry; linear dimensions (L) can be expressed as L = kW1/3 and surface area (S) as S = kW2/3, where k = a constant and W = the weight of the animal. Such equations have been used to determine the amount of space needed by standing (area [m2] = 0.019W0.66) and lying (area [m2] = 0.027W0.67) animals. Limited studies on the lying down and standing up behaviors of pigs and cattle suggest that the amount of space required can be estimated by area (m2) = 0.047W0.66. Linear space required per animal for behaviors such as feeding or drinking from a trough can be estimated from 0.064W0.33, but in groups this requirement will be affected by social interactions among group members and the amount of competition for the resource. Determining the amount of space for groups of animals is complex, as the amount of useable space can vary with group size and by how group members share space in time. Some studies have been conducted on the way in which groups of domestic fowl use space, but overall, we know very little about the ways in which livestock time-share space, synchronicity in the performance of behaviors, and the effects of spatial restrictions on behavior and welfare.

Mapping species differences for adventitious rooting in a Corymbia torelliana x Corymbia citriodora subspecies variegata hybrid

Quantitative trait loci (QTL) detection was carried out for adventitious rooting and associated propagation traits in a second-generation outbred Corymbia torelliana x Corymbia citriodora subspecies variegata hybrid family (n=186). The parental species of this cross are divergent in their capacity to develop roots adventitiously on stem cuttings and their propensity to form lignotubers. For the ten traits studied, there was one or two QTL detected, with some QTL explaining large amounts of phenotypic variation (e.g. 66% for one QTL for percentage rooting), suggesting that major effects influence rooting in this cross. Collocation of QTL for many strongly genetically correlated rooting traits to a single region on linkage group 12 suggested pleiotropy. A three locus model was most parsimonious for linkage group 12, however, as differences in QTL position and lower genetic correlations suggested separate loci for each of the traits of shoot production and root initiation. Species differences were thought to be the major source of phenotypic variation for some rooting rate and root quality traits because of the major QTL effects and up to 59-fold larger homospecific deviations (attributed to species differences) relative to heterospecific deviations (attributed to standing variation within species) evident at some QTL for these traits. A large homospecific/heterospecific ratio at major QTL suggested that the gene action evident in one cross may be indicative of gene action more broadly in hybrids between these species for some traits.

Time-dependent instantaneous mortality rates from multiple tagging experiments with exact times of release and recovery

Instantaneous natural mortality rates and a nonparametric hunting mortality function are estimated from a multiple-year tagging experiment with arbitrary, time-dependent fishing or hunting mortality. Our theory allows animals to be tagged over a range of times in each year, and to take time to mix into the population. Animals are recovered by hunting or fishing, and death events from natural causes occur but are not observed. We combine a long-standing approach based on yearly totals, described by Brownie et al. (1985, Statistical Inference from Band Recovery Data: A Handbook, Second edition, United States Fish and Wildlife Service, Washington, Resource Publication, 156), with an exact-time-of-recovery approach originated by Hearn, Sandland and Hampton (1987, Journal du Conseil International pour l'Exploration de la Mer, 43, 107-117), who modeled times at liberty without regard to time of tagging. Our model allows for exact times of release and recovery, incomplete reporting of recoveries, and potential tag shedding. We apply our methods to data on the heavily exploited southern bluefin tuna (Thunnus maccoyii).

Space allowances for confined livestock and their determination from allometric principles

The amount of space provided to animals governs important elements of their behaviour and, hence, is critical for their health and welfare. We review the use of allometric principles and equations to estimate the static space requirements of animals when standing and lying, and the space required for animals to feed, drink, stand-up and lie-down. We use the research literature relating to transportation and intensive housing of sheep and cattle to assess the validity of allometric equations for estimating space allowances. We investigated these areas because transportation and intensive housing provide points along a continuum in terms of the duration of confinement, (from hours to months) and spatial requirements are likely to increase with increasing duration of confinement, as animals will need to perform a greater behavioural repertoire for long-term survival, health and welfare. We find that, although there are theoretical reasons why allometric relationships to space allowances may vary slightly for different classes of stock, space allowances that have been demonstrated to have adverse effects on animal welfare during transportation correlated well with an inability to accommodate standing animals, as estimated from allometry. For intensive housing, we were able to detect a space allowance below which there were adverse effects on welfare. For short duration transportation during which animals remain standing, a space allowance per animal described by the allometric equation: area (m^2) = 0.020W^0.66, where W = liveweight (kg), would appear to be appropriate. Where it is desirable for all animals to lie simultaneously, then a minimum space allowance per animal described by the allometric equation: area (m^2) = 0.027W^0.66 appears to permit this, given that animals in a group time-share space. However, there are insufficient data to determine whether this allowance onboard a vehicle/vessel would enable animals to move and access food and water with ease. In intensive housing systems, a minimum space allowance per animal described by the allometric equation: area (m^2) = 0.033W^0.66 appears to be the threshold below which there are adverse effects on welfare. These suggested space allowances require verification with a range of species under different thermal conditions and, for transportation, under different conditions of vehicular/vessel stability. The minimum length of trough per animal (L in m) required for feeding and drinking can be determined from L = 0.064W^0.33, with the number of animals required to feed/drink simultaneously taken into account, together with any requirement to minimise competition. This also requires verification with a range of species. We conclude that allometric relationships are an appropriate basis for the formulation of space allowances for livestock.

Recovery of the red-finned blue-eye: An endangered fish from springs of the Great Artesian Basin

The red-finned blue-eye (Scaturiginichthys vermeilipinnis) is endemic to a single complex of springs emanating from the Great Artesian Basin, Australia. The species has been recorded as naturally occurring in eight separate very shallow (generally <20 mm) springs, with a combined wetland area of ~0.3 ha. Since its discovery in 1990, five red-finned blue-eye (RFBE) populations have been lost and subsequent colonisation has occurred in two spring wetlands. Current population size is estimated at <3000 individuals. Artesian bores have reduced aquifer pressure, standing water levels and spring-flows in the district. There is evidence of spatial separation within the spring pools where RFBE and the introduced fish gambusia (Gambusia holbrooki) co-occur, although both species are forced together when seasonal extremes affect spring size and water temperature. Gambusia was present in four of the five springs where RFBE populations have been lost. Four out of the five remaining subpopulations of RFBE are Gambusia free. Circumstantial evidence suggests that gambusia is a major threat to red-finned blue-eyes. The impact of Gambusia is probably exacerbated by domestic stock (cattle and sheep), feral goats and pigs that utilise the springs and can negatively affect water quality and flow patterns. Three attempts to translocate RFBE to apparently suitable springs elsewhere within the complex have failed. Opportunities to mitigate threats are discussed, along with directions for future research to improve management of this extremely threatened fish and habitat.

What lies beneath? The pattern and abundance of the subterranean tuber bank of the invasive liana cat's claw creeper, Macfadyena unguis-cati (Bignoniaceae)

Cat’s claw creeper, Macfadyena unguis-cati (L.) Gentry (Bignoniaceae) is a major environmental weed of riparian areas, rainforest communities and remnant natural vegetation in coastal Queensland and New South Wales, Australia. In densely infested areas, it smothers standing vegetation, including large trees, and causes canopy collapse. Quantitative data on the ecology of this invasive vine are generally lacking. The present study examines the underground tuber traits of M. unguis-cati and explores their links with aboveground parameters at five infested sites spanning both riparian and inland vegetation. Tubers were abundant in terms of density (~1000 per m2), although small in size and low in level of interconnectivity. M. unguis-cati also exhibits multiple stems per plant. Of all traits screened, the link between stand (stem density) and tuber density was the most significant and yielded a promising bivariate relationship for the purposes of estimation, prediction and management of what lies beneath the soil surface of a given M. unguis-cati infestation site. The study also suggests that new recruitment is primarily from seeds, not from vegetative propagation as previously thought. The results highlight the need for future biological-control efforts to focus on introducing specialist seed- and pod-feeding insects to reduce seed-output.

Variation in ecophysiology and carbon economy of invasive and native woody vines of riparian zones in south-eastern Queensland

Exotic and invasive woody vines are major environmental weeds of riparian areas, rainforest communities and remnant natural vegetation in coastal eastern Australia, where they smother standing vegetation, including large trees, and cause canopy collapse. We investigated, through glasshouse resource manipulative experiments, the ecophysiological traits that might facilitate faster growth, better resource acquisition and/or utilization and thus dominance of four exotic and invasive vines of South East Queensland, Australia, compared with their native counterparts. Relative growth rate was not significantly different between the two groups but water use efficiency (WUE) was higher in the native species while the converse was observed for light use efficiency (quantum efficiency, AQE) and maximum photosynthesis on a mass basis (Amax mass). The invasive species, as a group, also exhibited higher respiration load, higher light compensation point and higher specific leaf area. There were stronger correlations of leaf traits and greater structural (but not physiological) plasticity in invasive species than in their native counterparts. The scaling coefficients of resource use efficiencies (WUE, AQE and respiration efficiency) as well as those of fitness (biomass accumulated) versus many of the performance traits examined did not differ between the two species-origin groups, but there were indications of significant shifts in elevation (intercept values) and shifts along common slopes in many of these relationships – signalling differences in carbon economy (revenue returned per unit energy invested) and/or resource usage. Using ordination and based on 14 ecophysiological attributes, a fair level of separation between the two groups was achieved (51.5% explanatory power), with AQE, light compensation point, respiration load, WUE, specific leaf area and leaf area ratio, in decreasing order, being the main drivers. This study suggests similarity in trait plasticity, especially for physiological traits, but there appear to be fundamental differences in carbon economy and resource conservation between native and invasive vine species.

Quantitative and molecular genetics of juvenile wood traits in radiata and slash/Caribbean pines.

The Juvenile Wood Initiative (JWI) project has been running successfully since July 2003 under a Research Agreement with FWPA and Letters of Association with the consortium partners STBA (Southern Tree Breeding Association), ArborGen and FPQ (Forestry Plantations Queensland). Over the last five and half years, JWI scientists in CSIRO, FPQ, and STBA have completed all 12 major milestones and 28 component milestones according to the project schedule. We have made benchmark progress in understanding the genetic control of wood formation and interrelationships among wood traits. The project has made 15 primary scientific findings and several results have been adopted by industry as summarized below. This progress was detailed in 10 technical reports to funding organizations and industry clients. Team scientists produced 16 scientific manuscripts (8 published, 1 in press, 2 submitted, and several others in the process of submission) and 15 conference papers or presentations. Primary Scientific Findings. The 15 major scientific findings related to wood science, inheritance and the genetic basis of juvenile wood traits are: 1. An optimal method to predict stiffness of standing trees in slash/Caribbean pine is to combine gravimetric basic density from 12 mm increment cores with a standing tree prediction of MoE using a time of flight acoustic tool. This was the most accurate and cheapest way to rank trees for breeding selection for slash/Caribbean hybrid pine. This method was also recommended for radiata pine. 2. Wood density breeding values were predicted for the first time in the STBA breeding population using a large sample of 7,078 trees (increment cores) and it was estimated that selection of the best 250 trees for deployment will produce wood density gains of 12.4%. 3. Large genetic variation for a suite of wood quality traits including density, MFA, spiral grain, shrinkage, acoustic and non-acoustic stiffness (MoE) for clear wood and standing trees were observed. Genetic gains of between 8 and 49% were predicted for these wood quality traits with selection intensity between 1 to 10% for radiata pine. 4. Site had a major effect on juvenile-mature wood transition age and the effect of selective breeding for a shorter juvenile wood formation phase was only moderate (about 10% genetic gain with 10% selection intensity, equivalent to about 2 years reduction of juvenile wood). 5. The study found no usable site by genotype interactions for the wood quality traits of density, MFA and MoE for both radiata and slash/Caribbean pines, suggesting that assessment of wood properties on one or two sites will provide reliable estimates of the genetic worth of individuals for use in future breeding. 6. There were significant and sizable genotype by environment interactions between the mainland and Tasmanian regions and within Tasmania for DBH and branch size. 7. Strong genetic correlations between rings for density, MFA and MoE for both radiata and slash/Caribbean pines were observed. This suggests that selection for improved wood properties in the innermost rings would also result in improvement of wood properties in the subsequent rings, as well as improved average performance of the entire core. 8. Strong genetic correlations between pure species and hybrid performance for each of the wood quality traits were observed in the hybrid pines. Parental performance can be used to identify the hybrid families which are most likely to have superior juvenile wood properties of the slash/Caribbean F1 hybrid in southeast Queensland. 9. Large unfavourable genetic correlations between growth and wood quality traits were a prominent feature in radiata pine, indicating that overcoming this unfavourable genetic correlation will be a major technical issue in progressing radiata pine breeding. 10. The project created the first radiata pine 18 k cDNA microarray and generated 5,952 radiata pine xylogenesis expressed sequence tags (ESTs) which assembled into 3,304 unigenes. 11. A total of 348 genes were identified as preferentially expressed genes in earlywood or latewood while a total of 168 genes were identified as preferentially expressed genes in either juvenile or mature wood. 12. Juvenile earlywood has a distinct transcriptome relative to other stages of wood development. 13. Discovered rapid decay of linkage disequilibrium (LD) in radiata pine with LD decaying to approximately 50% within 1,700 base pairs (within a typical gene). A total of 913 SNPS from sequencing 177,380 base pairs were identified for association genetic studies. 14. 149 SNPs from 44 genes and 255 SNPs from a further 51 genes (total 95 genes) were selected for association analysis with 62 wood traits, and 30 SNPs were shortlisted for their significant association with variation of wood quality traits (density, MFA and MoE) with individual significant SNPs accounting for between 1.9 and 9.7% of the total genetic variation in traits. 15. Index selection using breeding objectives was the most profitable selection method for radiata pine, but in the long term it may not be the most effective in dealing with negative genetic correlations between wood volume and quality traits. A combination of economic and biological approaches may be needed to deal with the strong adverse correlation.

Seed production of Stylosanthes guyanensis. 1. Growth and development.

The pattern of growth and development of seed crops of stylo (Stylosanthes guyanensis) was derived from measurements made on experimental and commercial crops in north Queensland. The three cultivars Cook, Endeavour, and Schofield differed appreciably only in the timetable of their development. Each had distinct successive phases of vegetative and reproductive development culminating in total annual seed production of 700-800 kg ha-1 from a healthy closed canopy, the main recorded cause of reduced production being the disease Botrytis sp. In a healthy crop of Cook, the peak quantity of standing seed represented almost 90 per cent of the total accountable seed, and the rise to and decline from this peak proceeded at rates of the order of 3-4 per cent per day. It is deduced that, although there appears to be little potential for either increase in overall production or improvement in synchronization or retention characteristics beyond that currently attained by a closed canopy of healthy plants, there is scope for an increase in the efficiency of recovery of standing seed. Maximum recovery will be achieved through attention to choice of time of harvest, presentation of a minimum amount of extraneous vegetation to the harvester, and improvement in harvester separation.

Seed production of Stylosanthes guyanensis. 2. The consequences of defoliation.

The consequences of defoliation on seed production of stylo (Stylosanthes guyanensis) were examined in field experiments at Walkamin in north Queensland. The practical aim of defoliation is to present a level uncompacted crop canopy to the harvester without a reduction in the quantity of seed carried at harvest ripeness. It was concluded that the latest date at which defoliation is reasonably certain to achieve its objectives is about four weeks before first flower initiation. In north Queensland, this means late February for cvv. Cook and Endeavour and early April for cv. Schofield. The results suggest that development of the population of individual shoots must be synchronized to produce the highest peaks of standing seed; that this is best achieved by ensuring that a closed crop canopy with a ceiling shoot population exists at the time of first flower initiation; and that poorly synchronized shoot development is a consequence of defoliating too late and a cause of reduced seed production.

Seed production of Stylosanthes guyanensis. 3. Effects of pre-harvest desiccation.

Strips within commercial crops of Stylosanthes guyanensis in the Mareeba district of north Queensland were sprayed with diquat 4, 6 and 10 days before harvest and compared with unsprayed strips. Pre-harvest desiccation made combine harvesting easier, but did not increase harvest yield. Where seed formation and maturation was still possible, desiccation prevented this without substantially increasing the loss of seed to the ground; increased harvest efficiency was thus offset by a diminished quantity of standing seed. However, where there was little or no further potential for seed development, diquat had virtually no effect on the quantity of standing seed or harvest efficiency. It was concluded that the results warranted neither recommendation nor further evaluation of preharvest desiccation of S. guyanensis seed crops.