Molecular cloning and characterization of common carp (Cyprinus carpio L.) TCR gamma and CD3 gamma/delta chains

Partial cDNA sequences of TCR gamma and CD3 gamma/delta were isolated from the thymus of common carp (Cyprinus carpio L.) by the method of suppression subtractive hybridization (SSH). Subsequently the full length cDNAs of carp TCR gamma and CD3 gamma/delta were obtained by means of 3' RACE and 5' RACE, respectively. The full length of carp TCR gamma chain is 1368 bp and encodes 326 amino acids including a signal peptide region of 19 amino acids and a transmembrane region of 23 amino acids at the C-terminal region from aa 291 to 313. The V region of carp TCR gamma contains 109 amino acids, the core motif FGXG in J segment was also found in carp TCR gamma. The C region of carp TCR gamma contains the characteristic CX6PX6WX45C motif. The CP region of carp TCR C gamma contains 37 amino acids. The full length of carp CD3 gamma/delta is 790 bp and encodes 175 amino acids including a signal peptide region of 17 amino acids and a transmembrane region of 23 amino acids from aa 93 to 115. Similar to other known CD3 gamma/delta s, four cysteine residues in the extracellular domain and an immunoreceptor tyrosine-based activation motif ITAM (YxxL/Ix6-8YxxL/I) in the intracellular domain are also included in carp CD3 gamma/delta. Differing from other known CD3 gamma/delta s, carp CD3 gamma/delta tacks the CXXCXE motif in the extracellular domain. RTPCR analysis demonstrated that the expression of TCR gamma gene was mainly in the thymus and gill of 6-month carp, but in 18-month carp, TCR gamma gene was detected in all the examined tissues. The expression of CD3 gamma/delta gene was detected in all examined tissues of 6 and 18-month carp; among them, the highest expression level was in the thymus of 6-month carp. In situ hybridization showed that CD3 gamma/delta-expressing cells were widely distributed in the head kidney, spleen and kidney of carp, whereas in the thymus, they were densely distributed in the lymphoid outer zone and scattered in the epithelioid inner zone. (c) 2007 Published by Etsevier Ltd.

脉冲激光离散重熔热物理及组织性能研究

利用OM及FEM研究了铁基合金Nd:YAG脉冲激光熔凝区的几何形态及其变化规律、以及熔凝的热物理过程；利用OM、SEM、TEM、X-射线衍射仪及磨损实验机，研究了两种铁基热模具材料脉冲激光熔凝组织及其时效组织结构，以及熔凝区规则离散分布规律对材料抗磨损性能的影响。在10~5～10~7W/cm~2的脉冲激光平均功率密度范围内，可得到热传导型和深熔型两类强化区，当临界平均功率密度大于5 * 10~5W/cm~2，同时临界激光作用时间大于2ms时，热传导型强休区向深熔型强休区转变。熔化过程中，在熔池中形成上部以对流传热为主，底部以导热为主的传热模式，流场、温度场和压力场均随脉冲激光作用时间变化，最大流速、压力和温度梯度分别可达100m/s、数个大气压和10~(8-9) ℃C/m量级。凝固过程中，固液界面上的最大温度梯度、凝固速率和冷却速度时间和空间位置变化，分别可达10~(8-9) ℃/m量级、10~(-1)m/s量级和10~(7-8) ℃/s量级，其中冷却速度得到实验验证。亚共晶合金铸铁脉冲激光熔凝组织为δ-铁素体与M_3C的层片状共晶组织，还含有部分γ-奥氏体和少量的高碳孪晶马氏体组织，δ-铁素体和γ-奥氏体中均存在高密度位错亚结构。5CrMnMo钢脉冲激光熔凝组织由板条马氏体及少量的孪晶马氏体构成，马氏体中也存在高密度位错亚结构。上述两种组织经高温时效后，仍保持较细的晶粒，并有大量细小均匀弥散分布的碳化物析出，其中铸铁熔凝组织析出M_(23)C_6碳化物，M_(23)C_6可在M_3C/γ-奥氏体相界面或M_3C内部原位形核，亦可在δ-铁素体中弥散析出。两种材料的熔凝组织及其时效组织的显微硬度均明显高于相应的原始组织，也高于激光连续扫描熔凝的结果。脉冲激光规则离散熔凝加工在材料表面形成软硬相间的“原位”功能层，能显著降低裂纹形成的敏感性，提高材料表层的抗磨粒磨损性能，时效后仍具有较好的抗磨损性能。以熔凝强化区直径作为中心间距进行规则离散熔凝处理可使材料表面获得最佳抗磨损性能。

Biochemical and electron microscopic characterization of the F1F0 ATP Synthase from the hyperthermophilic eubacterium Aquifex aeolicus

The F1F0 ATP synthase has been purified from the hyperthermophilic eubacterium Aquifex aeolicus and characterized. Its subunits have been identified by MALDI-mass spectrometry through peptide mass fingerprinting and MS/MS. It contains the canonical subunits alpha, beta, gamma, delta and epsilon of F-1 and subunits a and c of F-0. Two versions of the b subunit were found, which show a low sequence homology to each other. Most likely they form a heterodimer. An electron microscopic single particle analysis revealed clear structural details, including two stalks connecting F-1 and F-0. In several orientations the central stalk appears to be tilted and/or kinked. It is unclear whether there is a direct connection between the peripheral stalk and the 6 subunit. (c) 2006 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

Optical properties of the E-0+Delta(0) energy level higher than the bandgap of GaAs studied by micro-photoluminescence technique

Using micro-photoluminescence technique, we observed a new photoluminescence peak about 0.348 eV above the bandgap of GaAs (E-0). By analyzing its optical characteristics, we assigned this peak to the nonequilibrium luminescence emission from the E-0 + Delta(0) bandgap in semi-insulated GaAs, which was further verified by Raman results. The observed polarization, excitation power dependence and temperature dependence of the photoluminescence spectra from the E-0 + Delta(0) energy level were very similar to those from the E-0 of GaAs. This mainly resulted from the common conduction band around Gamma(6) that was involved in the two optical transition processes, and indicated that the optical properties of bulk GaAs were mainly determined by the intrinsic properties of the conduction band. Our results demonstrated that the micro-photoluminescence technique is a powerful tool to investigate the high energy states above the fundamental bandgap in semiconductor materials.

Raman-forbidden mode and oxygen ordering in Bi2Sr2-xLaxCuO6+gamma single crystals annealed in oxygen

A Raman-forbidden phonon mode at about 840 cm(-1) is observed popularly on the surface of pun and La-doped Bi2Sr2-xLaxCuO6+y (0 less than or equal to x less than or equal to 0.8) single crystals annealed in oxygen. A remarkable excitation dependence of this additional line is found. Based on the properties of the structure of the Bi-O layer with excess oxygen atoms and the similarity in the appearance of the Raman-forbidden modes between RBa2Cu3Ox (R = Y, Nd, Gd, Pr) and Bi2Sr2-xLaxCuO6+y systems, we attribute the manifestation of this additional line to the ordering of the interstitial oxygen in the Bi-O layers. Our results provide Raman evidences for confirming that the ordering of the movable oxygen may exist universally in high-temperature superconductors.

Effect of gamma-radiation on the thermal and mechanical properties of a commercial poly(butylene adipate-co-terephthalate)

BACKGROUND: Poly(butylene adipate-co-terephthalate) (PBAT) has attracted wide interest as a biodegradable polymer. However, its use is restricted in certain applications due to its low melting point.RESULTS: PBAT was treated using gamma-radiation. The radiation features were analyzed using Soxhlet extraction, and the ratio of chain scission and crosslinking and gelation dose were determined using the classical Charlesby-Pinner equation. The results showed that PBAT is a radiation-crosslinkable polymer. The degree of crosslinking increased with increasing radiation dose; the relation between sol fraction and dose followed the Charlesby-Pinner equation. Differential scanning calorimetry analyses showed that the melting temperature (T-m) and the heat of fusion (Delta H-m) of PBAT exhibited almost no change in the first scan. The second scan, however, showed a decrease in T-m and Delta H-m. The glass transition temperature of irradiated PBAT increased with increasing radiation dose.

Effects of La2O3 on Microstructure and Wear Properties of Laser Clad gamma/Cr7C3/TiC Composite Coatings on TiAl Intermatallic Alloy

The effects of La2O3 addition on the microstructure and wear properties of laser clad gamma/C(r)7C(3)/TiC composite coatings on gamma-TiAl intermetallic alloy substrates with NiCr-Cr3C2 precursor mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive spectrometer (EDS) and block-on-ring wear tests. The responding wear mechanisms are discussed in detail. The results are compared with that for composite coating without La2O3. The comparison indicates that no evident new crystallographic phases are formed except a rapidly solidified microstructure consisting of the primary hard Cr7C3 and TiC carbides and the gamma/Cr7C3 eutectics distributed in the tough gamma nickel solid solution matrix. Good finishing coatings can be achieved under a proper amount of La2O3-addition and a suitable laser processing parameters. The additions of rare-earth oxide La,03 can refine and purify the microstructure of coatings, relatively decrease the volume fraction of primary blocky Cr7C3 to Cr7C3/gamma eutectics, reduce the dilution of clad material from base alloy and increase the microhardness of the coatings. When the addition of La2O3 is approximately 4 wt.%, the laser clad composite coating possesses the highest hardness and toughness. The composite coating with 4 wt.%La2O3 addition can result the best enhancement of wear resistance of about 30%. However, too less or excessive addition amount of La2O3 have no better influence on wear resistance of the composite coating.

微碳深冲钢板的非｛111｝织构特征及其对r,△r值的影响

From St15 micro-carbon deep drawing steel sheets, two sets of samples with (r) over bar variant and Deltar constant, and (r) over bar constant and Deltar variant, were selected to carry out texture measurement and ODF analysis. A description of the texture characteristics and an investigation on the effect of the main textures on the (r) over bar and Deltar values were given. The results show that in the tested steel sheets no desired gamma < 111 > parallel to ND orientation line appears but gamma' orientation line located at <()over bar>=0-90 degrees, theta =19 degrees and phi =45 degrees, and L orientation line located around gamma < 111 > parallel to ND orientation line which spirally rotates from Psi =0 degrees, theta =54.7 degrees and phi =62.7 degrees to Psi =90 degrees, theta =40 degrees and phi =45 degrees occur. Among them, the L orientation line has a main influence on the (r) over bar value and the stronger the texture density, the higher the (r) over bar value is, but is somewhat detrimental to the Deltar value; at the same time, the gamma' orientation line has a major effect on the Deltar value in an opposite way, but is somewhat deteriorative to the (r) over bar value. A strong L orientation line superposed by a relatively strong gamma' orientation line may produce fine (r) over bar and Deltar values.

General Solution to Two-Dimensional Nonslipping JKR Model with a Pulling Force in an Arbitrary Direction

In this paper, a generalized JKR model is investigated, in which an elastic cylinder adhesively contacts with an elastic half space and the contact region is assumed to be perfect bonding. An external pulling force is acted on the cylinder in an arbitrary direction. The contact area changes during the pull-off process, which can be predicted using the dynamic Griffith energy balance criterion as the contact edge shifts. Full coupled solution with an oscillatory singularity is obtained and analyzed by numerical calculations. The effect of Dundurs' parameter on the pull-off process is analyzed, which shows that a nonoscillatory solution can approximate the general one under some conditions, i.e., larger pulling angle (pi/2 is the maximum value), smaller a/R or larger nondimensional parameter value of Delta gamma/E*R. Relations among the contact half width, the external pulling force and the pulling angle are used to determine the pull-off force and pull-off contact half width explicitly. All the results in the present paper as basic solutions are helpful and applicable for experimenters and engineers.

Microstructure and Tribological Properties of Laser Clad gamma/Cr7C3/Tic Composite Coatings on gamma-TiA1 Intermetallic Alloy

In order to improve the wear resistance of the gamma-TiAl intermetallic alloy, microstructure, room- and high-temperature (600 degrees C) wear behaviors of laser clad gamma/Cr7C3/TiC composite coatings with different constitution of NiCr-Cr3C2 precursor-mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectrometer (EDS), block-on-ring (room-temperature) and pin-on-disk (high-temperature) wear tests. The responding wear mechanisms are discussed in detail. Results show that microstructures of the laser clad composite coatings have non-equilibrium solidified microstructures consisting of primary hard Cr7C3 and TiC carbides and the inter-primary gamma/Cr7C3 eutectic matrix, about three to five times higher average microhardness compared with the TiAl alloy substrate. Higher wear resistance than the original TiAl alloy is achieved in the clad composite coatings under dry sliding wear conditions, which is closely related to the formation of non-equilibrium solidified reinforced Cr7C3 and TiC carbides and the positive contribution of the relatively ductile and tough gamma/Cr7C3 eutectics matrix and their stability under high-temperature exposure.

Gamma -> Epsilon Martensite Transformation and Twinning Deformation in fcc Cobalt During Surface Mechanical Attrition Treatment

The deformation microstructure of face-centered cubic cobalt subjected to surface mechanical attrition treatment was studied as a function of strain levels. Strain-induced gamma --> epsilon transformation and twinning deformation were evidenced by transmission electron microscopy and were found to progress continuously in ultrafine and nanocrystalline grains as the strain increased.

Effect of Work of Adhesion on Nanoindentation

Three adhesion contact models, JKR (Johnson-Kendall-Roberts), DMT (Derjaguin-Muller-Toporov) and MD (Maugis-Dugdale) are compared with the Hertz model in dealing with the nano-contact problems. It has been shown that the dimensionless load parameter, $\bar{P}=P/(\pi\Delta\gamma R)$, and the transition parameter, $\Lambda$, have significant influences on the contact stiffness (contact area) at micro/nano-scale and should not be ignored in shallow nanoindentation.

等离子熔覆gamma/Cr7C3复合材料涂层组织与耐磨性研究

为探索提高工程机械易损零部件服役寿命的新技术,采用等离子熔覆工艺,以Ni-Cr-C混合合金粉末为添加材料,在易损零部件用钢Q235表面形成了以初生块状金属陶瓷Cr7C3为硬质耐磨相,以强韧性良好的γ/Cr7C3共晶为基体的复合材料冶金涂层,分析了涂层的显微组织和硬度,在室温干滑动磨损条件下测试了其耐磨性.研究结果表明:涂层组织致密,硬度较高,与基体之间为完全的冶金结合,在干滑动磨损条件下具有良好的耐磨性.

Gamma-Ray Attenuation Technique For Measuring Void Fraction In Horizontal Gas-Liquid Two-Phase Flow

The measurement of void fraction is of importance to the oil industry and chemical industry. In this article, the principle and mathematical method of determining the void fraction of horizontal gas-liquid flow by using a single-energy gamma-ray system is described. The gamma-ray source is the radioactive isotope of Am-241 with gamma-ray energy of 59.5 keV. The time-averaged value of the void fraction in a 50.0-mm i.d. transparent horizontal pipeline is measured under various combinations of the liquid flow and gas flow. It is found that increasing the gas flow rate at a fixed liquid flow rate would increase the void fraction. Test data are compared with the predictions of the correlations and a good agreement is found. The result shows that the designed gamma-ray system can be used for measuring the void fraction in a horizontal gas-liquid two-phase flow with high accuracy.

Microstructure and high-temperature wear and oxidation resistance of laser clad gamma/W2C/TiC composite coatings on gamma-TiAl intermetallic alloy

There are very strong interests in improving the high-temperature wear resistance of the y-TiAl intermetallic alloy, especially when applied as tribological moving components. In this paper, microstructure, high-temperature dry sliding wear at 600 degrees C and isothermal oxidation at 1000 degrees C on ambient air of laser clad gamma/W2C/TiC composite coatings with different constitution of Ni-Cr-W-C precursor mixed powders on TiAl alloy substrates have been investigated. The results show that microstructure of the laser fabricated composite coatings possess non-equilibrium microstructure consisting of the matrix of nickel-base solid solution gamma-NiCrAl and reinforcements of TiC, W2C and M23C6 carbides. Higher wear resistance than the original TiAl alloy is achieved in the composite coatings under high-temperature wear test conditions. However, the oxidation resistance of the laser clad gamma/W2C/TiC composite coatings is deceased. The corresponding mechanisms resulting in the above behaviors of the laser clad composite coatings are discussed. (c) 2006 Elsevier B.V. All rights reserved.