Discriminant Analysis of Geographical Origin of Cork Planks and Stoppers by Near Infrared Spectroscopy

The objective of this study was to assess the potential of visible and near infrared spectroscopy (VIS+NIRS) combined with multivariate analysis for identifying the geographical origin of cork. The study was carried out on cork planks and natural cork stoppers from the most representative cork-producing areas in the world. Two training sets of international and national cork planks were studied. The first set comprised a total of 479 samples from Morocco, Portugal, and Spain, while the second set comprised a total of 179 samples from the Spanish regions of Andalusia, Catalonia, and Extremadura. A training set of 90 cork stoppers from Andalusia and Catalonia was also studied. Original spectroscopic data were obtained for the transverse sections of the cork planks and for the body and top of the cork stoppers by means of a 6500 Foss-NIRSystems SY II spectrophotometer using a fiber optic probe. Remote reflectance was employed in the wavelength range of 400 to 2500 nm. After analyzing the spectroscopic data, discriminant models were obtained by means of partial least square (PLS) with 70% of the samples. The best models were then validated using 30% of the remaining samples. At least 98% of the international cork plank samples and 95% of the national samples were correctly classified in the calibration and validation stage. The best model for the cork stoppers was obtained for the top of the stoppers, with at least 90% of the samples being correctly classified. The results demonstrate the potential of VIS + NIRS technology as a rapid and accurate method for predicting the geographical origin of cork plank and stoppers

Detection and quantification of peanut traces in wheat flour by near infrared hyperspectral imaging spectroscopy using principal-component analysis

The use of a common environment for processing different powder foods in the industry has increased the risk of finding peanut traces in powder foods. The analytical methods commonly used for detection of peanut such as enzyme-linked immunosorbent assay (ELISA) and real-time polymerase chain reaction (RT-PCR) represent high specificity and sensitivity but are destructive and time-consuming, and require highly skilled experimenters. The feasibility of NIR hyperspectral imaging (HSI) is studied for the detection of peanut traces down to 0.01% by weight. A principal-component analysis (PCA) was carried out on a dataset of peanut and flour spectra. The obtained loadings were applied to the HSI images of adulterated wheat flour samples with peanut traces. As a result, HSI images were reduced to score images with enhanced contrast between peanut and flour particles. Finally, a threshold was fixed in score images to obtain a binary classification image, and the percentage of peanut adulteration was compared with the percentage of pixels identified as peanut particles. This study allowed the detection of traces of peanut down to 0.01% and quantification of peanut adulteration from 10% to 0.1% with a coefficient of determination (r2) of 0.946. These results show the feasibility of using HSI systems for the detection of peanut traces in conjunction with chemical procedures, such as RT-PCR and ELISA to facilitate enhanced quality-control surveillance on food-product processing lines.

On-line measurement of soil properties without direct spectral response in near infrared spectral range

So far, the majority of reports on on-line measurement considered soil properties with direct spectral responses in near infrared spectroscopy (NIRS). This work reports on the results of on-line measurement of soil properties with indirect spectral responses, e.g. pH, cation exchange capacity (CEC), exchangeable calcium (Caex) and exchangeable magnesium (Mgex) in one field in Bedfordshire in the UK. The on-line sensor consisted of a subsoiler coupled with an AgroSpec mobile, fibre type, visible and near infrared (vis–NIR) spectrophotometer (tec5 Technology for Spectroscopy, Germany), with a measurement range 305–2200 nm to acquire soil spectra in diffuse reflectance mode. General calibration models for the studied soil properties were developed with a partial least squares regression (PLSR) with one-leave-out cross validation, using spectra measured under non-mobile laboratory conditions of 160 soil samples collected from different fields in four farms in Europe, namely, Czech Republic, Denmark, Netherland and UK. A group of 25 samples independent from the calibration set was used as independent validation set. Higher accuracy was obtained for laboratory scanning as compared to on-line scanning of the 25 independent samples. The prediction accuracy for the laboratory and on-line measurements was classified as excellent/very good for pH (RPD = 2.69 and 2.14 and r2 = 0.86 and 0.78, respectively), and moderately good for CEC (RPD = 1.77 and 1.61 and r2 = 0.68 and 0.62, respectively) and Mgex (RPD = 1.72 and 1.49 and r2 = 0.66 and 0.67, respectively). For Caex, very good accuracy was calculated for laboratory method (RPD = 2.19 and r2 = 0.86), as compared to the poor accuracy reported for the on-line method (RPD = 1.30 and r2 = 0.61). The ability of collecting large number of data points per field area (about 12,800 point per 21 ha) and the simultaneous analysis of several soil properties without direct spectral response in the NIR range at relatively high operational speed and appreciable accuracy, encourage the recommendation of the on-line measurement system for site specific fertilisation.

Non-destructive optical characterization of fruits in the red and near infrared.

Increasing attention is being paid to the possible development of non-invasive tests for the assessment of the quality of Fruits. We propose a novel non-destructive method for the measurement of the internal optical properties of fruits and vegetables by means of lime-resolved reflectance spectroscopy in the visible and NIR range. A Fully automated instrumentation for time-resolved reflectance measurements was developed. It is based on mode-locked laser sources and electronics for time-correlated single photon counting, and provides a time-resolution of 120-160 ps. The system was used to probe the optical properties of several species and varieties of Fruits and vegetables in the red and NIR range (650-1000 nm). In most Fruits, the absorption line shape is dominated by the absorption peak of water, centred around 970 nm. Generally, the absorption spectra also show the spectral features typical of chlorophyll, with maximum at 675 nm. In particular, for what concerns apples, variations in peak intensity are observed depending on the variety, the degree of ripeness as well as the position on the apple. For all the species and varieties considered, the transport scattering coefficient decreases progressively upon increasing the wavelength.

Near infrared high efficiency InAs/GaAsSb QDLEDs: band alignment and carrier recombination mechanisms

The development of high efficiency laser diodes (LD) and light emitting diodes (LED) covering the 1.0 to 1.55 μm region of the spectra using GaAs heteroepitaxy has been long pursued. Due to the lack of materials that can be grown lattice-macthed to GaAs with bandgaps in the 1.0 to 1.55 μm region, quantum wells (QW) or quantum dots (QD) need be used. The most successful approach with QWs has been to use InGaAs, but one needs to add another element, such as N, to be able to reach 1.3/1.5μm. Even though LDs have been successfully demonstrated with the QW approach, using N leads to problems with compositional homogeneity across the wafer, and limited efficiency due to strong non-radiative recombination. The alternative approach of using InAs QDs is an attractive option, but once again, to reach the longest wavelengths one needs very large QDs and control over the size distribution and band alignment. In this work we demonstrate InAs/GaAsSb QDLEDs with high efficiencies, emitting from 1.1 to 1.52 μm, and we analyze the band alignment and carrier loss mechanisms that result from the presence of Sb in the capping layer.

Non-destructive optical characterisation of fruits with time-resolved reflectance spectroscopy.

Increasing attention is being paid to the possible development of non-invasive tests for the assessment of the quality of fruits We propose a novel non-destructive method for the measurement of the internal optical properties of fruits and vegetables by means of time resolved reflectance spectroscopy in the visible and NIR range. A fully automated instrumentation for time-resolved reflectance measurements was developed It is based on mode-locked laser sources and electronics for time-correlated single photon counting, and provides a time-resolution of 120-160 ps The system was used to probe the optical properties of several species and varieties of fruits and vegetables in the red and NIR range (650-1000 nm). In most fruits, the absorption line shape is dominated by the absorption peak of water, centred around 970 nm Generally, the absorption spectra also show the spectral features typical of chlorophyll, with maximum at 675 nm In particular, for what concerns apples, variations in peak intensity are observed depending on the variety, the degree of ripeness as well as the position on the apple. For all the species and varieties considered, the transport scattering coefficient decreases progressively upon increasing the wavelength.

Models for internal quality sorting of fruit, based on time-domain laser reflectance spectroscopy (TDRS).

Non-destructive measurement of fruit quality has been an important objective through recent years (Abbott, 1999). Near infrared spectroscopy (NIR) is applicable to the cuantification of chemicals in foods and NIK "laser spectroscopy" can be used to estimate the firmness of fruits. However, die main limitation of current optical techniques that measure light transmission is that they do not account for the coupling between absorption and scattering inside the tissue, when quantifying the intensity o f reemitted light. The solution o f this l i m i t a t i o n was the goal o f the present work.

Photoacoustic effect measurement in aqueous suspensions of gold nanorods caused by low-frequency and low-power near-infrared pulsing laser irradiation

When aqueous suspensions of gold nanorods are irradiated with a pulsing laser (808 nm), pressure waves appear even at low frequencies (pulse repetition rate of 25 kHz). We found that the pressure wave amplitude depends on the dynamics of the phenomenon. For fixed concentration and average laser current intensity, the amplitude of the pressure waves shows a trend of increasing with the pulse slope and the pulse maximum amplitude.We postulate that the detected ultrasonic pressure waves are a sort of shock waves that would be generated at the beginning of each pulse, because the pressure wave amplitude would be the result of the positive interference of all the individual shock waves.

A portable NIR device for the optical supervision of milk coagulation process

The coagulation of milk is the fundamental process in cheese-making, based on a gel formation as consequence of physicochemical changes taking place in the casein micelles, the monitoring the whole process of milk curd formation is a constant preoccupation for dairy researchers and cheese companies (Lagaude et al., 2004). In addition to advances in composition-based applications of near infrared spectroscopy (NIRS), innovative uses of this technology are pursuing dynamic applications that show promise, especially in regard to tracking a sample in situ during food processing (Bock and Connelly, 2008). In this way the literature describes cheese making process applications of NIRS for curd cutting time determination, which conclude that NIRS would be a suitable method of monitoring milk coagulation, as shown i.e. the works published by Fagan et al. (Fagan et al., 2008; Fagan et al., 2007), based in the use of the commercial CoAguLite probe (with a LED at 880nm and a photodetector for light reflectance detection).

Independent component analysis for the identification of sources of variation on an industrial nirs application

A Near Infrared Spectroscopy (NIRS) industrial application was developed by the LPF-Tagralia team, and transferred to a Spanish dehydrator company (Agrotécnica Extremeña S.L.) for the classification of dehydrator onion bulbs for breeding purposes. The automated operation of the system has allowed the classification of more than one million onion bulbs during seasons 2004 to 2008 (Table 1). The performance achieved by the original model (R2=0,65; SEC=2,28ºBrix) was enough for qualitative classification thanks to the broad range of variation of the initial population (18ºBrix). Nevertheless, a reduction of the classification performance of the model has been observed with the passing of seasons. One of the reasons put forward is the reduction of the range of variation that naturally occurs during a breeding process, the other is the variations in other parameters than the variable of interest but whose effects would probably be affecting the measurements [1]. This study points to the application of Independent Component Analysis (ICA) on this highly variable dataset coming from a NIRS industrial application for the identification of the different sources of variation present through seasons.

Nondestructive quantification of chemical and physical properties of fruits by time-resolved reflectance spectroscopy in the wavelength range 650-1000 nm

Time-resolved reflectance spectroscopy can be used to assess nondestructively the bulk (rather than the superficial) optical properties of highly diffusive media. A fully automated system for time-resolved reflectance spectroscopy was used to evaluate the absorption and the transport scattering spectra of fruits in the red and the near-infrared regions. In particular, data were collected in the range 650-1000 nm from three varieties of apples and from peaches, kiwifruits, and tomatoes. The absorption spectra were usually dominated by the water peak near 970 nm, whereas chlorophyll was detected at 675 nm. For ail species the scattering decreased progressively with increasing wavelength. A best fit to water and chlorophyll absorption line shapes and to Mie theory permitted the estimation of water and chlorophyll content and the average size of scattering centers in the bulls; of intact fruits.

Photon Management Structures for Absorption Enhancement in Intermediate Band Solar Cells and Crystalline Silicon Solar Cells

El objetivo de la tesis es investigar los beneficios que el atrapamiento de la luz mediante fenómenos difractivos puede suponer para las células solares de silicio cristalino y las de banda intermedia. Ambos tipos de células adolecen de una insuficiente absorción de fotones en alguna región del espectro solar. Las células solares de banda intermedia son teóricamente capaces de alcanzar eficiencias mucho mayores que los dispositivos convencionales (con una sola banda energética prohibida), pero los prototipos actuales se resienten de una absorción muy débil de los fotones con energías menores que la banda prohibida. Del mismo modo, las células solares de silicio cristalino absorben débilmente en el infrarrojo cercano debido al carácter indirecto de su banda prohibida. Se ha prestado mucha atención a este problema durante las últimas décadas, de modo que todas las células solares de silicio cristalino comerciales incorporan alguna forma de atrapamiento de luz. Por razones de economía, en la industria se persigue el uso de obleas cada vez más delgadas, con lo que el atrapamiento de la luz adquiere más importancia. Por tanto aumenta el interés en las estructuras difractivas, ya que podrían suponer una mejora sobre el estado del arte. Se comienza desarrollando un método de cálculo con el que simular células solares equipadas con redes de difracción. En este método, la red de difracción se analiza en el ámbito de la óptica física, mediante análisis riguroso con ondas acopladas (rigorous coupled wave analysis), y el sustrato de la célula solar, ópticamente grueso, se analiza en los términos de la óptica geométrica. El método se ha implementado en ordenador y se ha visto que es eficiente y da resultados en buen acuerdo con métodos diferentes descritos por otros autores. Utilizando el formalismo matricial así derivado, se calcula el límite teórico superior para el aumento de la absorción en células solares mediante el uso de redes de difracción. Este límite se compara con el llamado límite lambertiano del atrapamiento de la luz y con el límite absoluto en sustratos gruesos. Se encuentra que las redes biperiódicas (con geometría hexagonal o rectangular) pueden producir un atrapamiento mucho mejor que las redes uniperiódicas. El límite superior depende mucho del periodo de la red. Para periodos grandes, las redes son en teoría capaces de alcanzar el máximo atrapamiento, pero sólo si las eficiencias de difracción tienen una forma peculiar que parece inalcanzable con las herramientas actuales de diseño. Para periodos similares a la longitud de onda de la luz incidente, las redes de difracción pueden proporcionar atrapamiento por debajo del máximo teórico pero por encima del límite Lambertiano, sin imponer requisitos irrealizables a la forma de las eficiencias de difracción y en un margen de longitudes de onda razonablemente amplio. El método de cálculo desarrollado se usa también para diseñar y optimizar redes de difracción para el atrapamiento de la luz en células solares. La red propuesta consiste en un red hexagonal de pozos cilíndricos excavados en la cara posterior del sustrato absorbente de la célula solar. La red se encapsula en una capa dieléctrica y se cubre con un espejo posterior. Se simula esta estructura para una célula solar de silicio y para una de banda intermedia y puntos cuánticos. Numéricamente, se determinan los valores óptimos del periodo de la red y de la profundidad y las dimensiones laterales de los pozos para ambos tipos de células. Los valores se explican utilizando conceptos físicos sencillos, lo que nos permite extraer conclusiones generales que se pueden aplicar a células de otras tecnologías. Las texturas con redes de difracción se fabrican en sustratos de silicio cristalino mediante litografía por nanoimpresión y ataque con iones reactivos. De los cálculos precedentes, se conoce el periodo óptimo de la red que se toma como una constante de diseño. Los sustratos se procesan para obtener estructuras precursoras de células solares sobre las que se realizan medidas ópticas. Las medidas de reflexión en función de la longitud de onda confirman que las redes cuadradas biperiódicas consiguen mejor atrapamiento que las uniperiódicas. Las estructuras fabricadas se simulan con la herramienta de cálculo descrita en los párrafos precedentes y se obtiene un buen acuerdo entre la medida y los resultados de la simulación. Ésta revela que una fracción significativa de los fotones incidentes son absorbidos en el reflector posterior de aluminio, y por tanto desaprovechados, y que este efecto empeora por la rugosidad del espejo. Se desarrolla un método alternativo para crear la capa dieléctrica que consigue que el reflector se deposite sobre una superficie plana, encontrándose que en las muestras preparadas de esta manera la absorción parásita en el espejo es menor. La siguiente tarea descrita en la tesis es el estudio de la absorción de fotones en puntos cuánticos semiconductores. Con la aproximación de masa efectiva, se calculan los niveles de energía de los estados confinados en puntos cuánticos de InAs/GaAs. Se emplea un método de una y de cuatro bandas para el cálculo de la función de onda de electrones y huecos, respectivamente; en el último caso se utiliza un hamiltoniano empírico. La regla de oro de Fermi permite obtener la intensidad de las transiciones ópticas entre los estados confinados. Se investiga el efecto de las dimensiones del punto cuántico en los niveles de energía y la intensidad de las transiciones y se obtiene que, al disminuir la anchura del punto cuántico respecto a su valor en los prototipos actuales, se puede conseguir una transición más intensa entre el nivel intermedio fundamental y la banda de conducción. Tomando como datos de partida los niveles de energía y las intensidades de las transiciones calculados como se ha explicado, se desarrolla un modelo de equilibrio o balance detallado realista para células solares de puntos cuánticos. Con el modelo se calculan las diferentes corrientes debidas a transiciones ópticas entre los numerosos niveles intermedios y las bandas de conducción y de valencia bajo ciertas condiciones. Se distingue de modelos de equilibrio detallado previos, usados para calcular límites de eficiencia, en que se adoptan suposiciones realistas sobre la absorción de fotones para cada transición. Con este modelo se reproducen datos publicados de eficiencias cuánticas experimentales a diferentes temperaturas con un acuerdo muy bueno. Se muestra que el conocido fenómeno del escape térmico de los puntos cuánticos es de naturaleza fotónica; se debe a los fotones térmicos, que inducen transiciones entre los estados excitados que se encuentran escalonados en energía entre el estado intermedio fundamental y la banda de conducción. En el capítulo final, este modelo realista de equilibrio detallado se combina con el método de simulación de redes de difracción para predecir el efecto que tendría incorporar una red de difracción en una célula solar de banda intermedia y puntos cuánticos. Se ha de optimizar cuidadosamente el periodo de la red para equilibrar el aumento de las diferentes transiciones intermedias, que tienen lugar en serie. Debido a que la absorción en los puntos cuánticos es extremadamente débil, se deduce que el atrapamiento de la luz, por sí solo, no es suficiente para conseguir corrientes apreciables a partir de fotones con energía menor que la banda prohibida en las células con puntos cuánticos. Se requiere una combinación del atrapamiento de la luz con un incremento de la densidad de puntos cuánticos. En el límite radiativo y sin atrapamiento de la luz, se necesitaría que el número de puntos cuánticos de una célula solar se multiplicara por 1000 para superar la eficiencia de una célula de referencia con una sola banda prohibida. En cambio, una célula con red de difracción precisaría un incremento del número de puntos en un factor 10 a 100, dependiendo del nivel de la absorción parásita en el reflector posterior. Abstract The purpose of this thesis is to investigate the benefits that diffractive light trapping can offer to quantum dot intermediate band solar cells and crystalline silicon solar cells. Both solar cell technologies suffer from incomplete photon absorption in some part of the solar spectrum. Quantum dot intermediate band solar cells are theoretically capable of achieving much higher efficiencies than conventional single-gap devices. Present prototypes suffer from extremely weak absorption of subbandgap photons in the quantum dots. This problem has received little attention so far, yet it is a serious barrier to the technology approaching its theoretical efficiency limit. Crystalline silicon solar cells absorb weakly in the near infrared due to their indirect bandgap. This problem has received much attention over recent decades, and all commercial crystalline silicon solar cells employ some form of light trapping. With the industry moving toward thinner and thinner wafers, light trapping is becoming of greater importance and diffractive structures may offer an improvement over the state-of-the-art. We begin by constructing a computational method with which to simulate solar cells equipped with diffraction grating textures. The method employs a wave-optical treatment of the diffraction grating, via rigorous coupled wave analysis, with a geometric-optical treatment of the thick solar cell bulk. These are combined using a steady-state matrix formalism. The method has been implemented computationally, and is found to be efficient and to give results in good agreement with alternative methods from other authors. The theoretical upper limit to absorption enhancement in solar cells using diffractions gratings is calculated using the matrix formalism derived in the previous task. This limit is compared to the so-called Lambertian limit for light trapping with isotropic scatterers, and to the absolute upper limit to light trapping in bulk absorbers. It is found that bi-periodic gratings (square or hexagonal geometry) are capable of offering much better light trapping than uni-periodic line gratings. The upper limit depends strongly on the grating period. For large periods, diffraction gratings are theoretically able to offer light trapping at the absolute upper limit, but only if the scattering efficiencies have a particular form, which is deemed to be beyond present design capabilities. For periods similar to the incident wavelength, diffraction gratings can offer light trapping below the absolute limit but above the Lambertian limit without placing unrealistic demands on the exact form of the scattering efficiencies. This is possible for a reasonably broad wavelength range. The computational method is used to design and optimise diffraction gratings for light trapping in solar cells. The proposed diffraction grating consists of a hexagonal lattice of cylindrical wells etched into the rear of the bulk solar cell absorber. This is encapsulated in a dielectric buffer layer, and capped with a rear reflector. Simulations are made of this grating profile applied to a crystalline silicon solar cell and to a quantum dot intermediate band solar cell. The grating period, well depth, and lateral well dimensions are optimised numerically for both solar cell types. This yields the optimum parameters to be used in fabrication of grating equipped solar cells. The optimum parameters are explained using simple physical concepts, allowing us to make more general statements that can be applied to other solar cell technologies. Diffraction grating textures are fabricated on crystalline silicon substrates using nano-imprint lithography and reactive ion etching. The optimum grating period from the previous task has been used as a design parameter. The substrates have been processed into solar cell precursors for optical measurements. Reflection spectroscopy measurements confirm that bi-periodic square gratings offer better absorption enhancement than uni-periodic line gratings. The fabricated structures have been simulated with the previously developed computation tool, with good agreement between measurement and simulation results. The simulations reveal that a significant amount of the incident photons are absorbed parasitically in the rear reflector, and that this is exacerbated by the non-planarity of the rear reflector. An alternative method of depositing the dielectric buffer layer was developed, which leaves a planar surface onto which the reflector is deposited. It was found that samples prepared in this way suffered less from parasitic reflector absorption. The next task described in the thesis is the study of photon absorption in semiconductor quantum dots. The bound-state energy levels of in InAs/GaAs quantum dots is calculated using the effective mass approximation. A one- and four- band method is applied to the calculation of electron and hole wavefunctions respectively, with an empirical Hamiltonian being employed in the latter case. The strength of optical transitions between the bound states is calculated using the Fermi golden rule. The effect of the quantum dot dimensions on the energy levels and transition strengths is investigated. It is found that a strong direct transition between the ground intermediate state and the conduction band can be promoted by decreasing the quantum dot width from its value in present prototypes. This has the added benefit of reducing the ladder of excited states between the ground state and the conduction band, which may help to reduce thermal escape of electrons from quantum dots: an undesirable phenomenon from the point of view of the open circuit voltage of an intermediate band solar cell. A realistic detailed balance model is developed for quantum dot solar cells, which uses as input the energy levels and transition strengths calculated in the previous task. The model calculates the transition currents between the many intermediate levels and the valence and conduction bands under a given set of conditions. It is distinct from previous idealised detailed balance models, which are used to calculate limiting efficiencies, since it makes realistic assumptions about photon absorption by each transition. The model is used to reproduce published experimental quantum efficiency results at different temperatures, with quite good agreement. The much-studied phenomenon of thermal escape from quantum dots is found to be photonic; it is due to thermal photons, which induce transitions between the ladder of excited states between the ground intermediate state and the conduction band. In the final chapter, the realistic detailed balance model is combined with the diffraction grating simulation method to predict the effect of incorporating a diffraction grating into a quantum dot intermediate band solar cell. Careful optimisation of the grating period is made to balance the enhancement given to the different intermediate transitions, which occur in series. Due to the extremely weak absorption in the quantum dots, it is found that light trapping alone is not sufficient to achieve high subbandgap currents in quantum dot solar cells. Instead, a combination of light trapping and increased quantum dot density is required. Within the radiative limit, a quantum dot solar cell with no light trapping requires a 1000 fold increase in the number of quantum dots to supersede the efficiency of a single-gap reference cell. A quantum dot solar cell equipped with a diffraction grating requires between a 10 and 100 fold increase in the number of quantum dots, depending on the level of parasitic absorption in the rear reflector.

Relationship among slurry characteristics and gaseous emissions at different types of commercial Spanish pig farms

This study aimed to analyse several factors of variation of slurry composition and to establish prediction equations for potential methane (CH4) and ammonia (NH3) emissions. Seventy-nine feed and slurry samples were collected at two seasons (summer and winter) from commercial pig farms sited at two Spanish regions (Centre and Mediterranean). Nursery, growing-fattening, gestating and lactating facilities were sampled. Feed and slurry composition were determined, and potential CH4 and NH3 emissions measured at laboratory. Feed nutrient contents were used as covariates in the analysis. Near infrared reflectance spectroscopy (NIRS) was evaluated as a predicting tool for slurry composition and potential gaseous emissions. A wide variability was found both in feed and slurry composition. Mediterranean farms had a higher pH (p<0.001) and ash (p=0.02) concentration than those located at the Centre of Spain. Also, type of farm affected ether extract content of the slurry (p=0.02), with highest values obtained for the youngest animal facilities. Results suggested a buffer effect of dietary fibre on slurry pH and a direct relationship (p<0.05) with fibre constituents of manure. Dietary protein content did not affect slurry nitrogen content but decreased (p=0.003) total and volatile solids concentration. Prediction models of potential NH3 emissions (R2=0.89) and CH4 yield (R2=0.61) were obtained from slurry composition. Predictions from NIRS showed a high accuracy for most slurry constituents (R2>0.90) and similar accuracy of prediction of potential NH3 and CH4 emissions (R2=0.84 and 0.68, respectively) to models using slurry characteristics, which can be of interest to estimate emissions from commercial farms and establish mitigation strategies or optimize biogas production.

Ammonia and methane gas emissions from pig slurry: variability induced through feeding strategies

Esta Tesis doctoral fue desarrollada para estudiar las emisiones de amoniaco (NH3) y metano (CH4) en purines de cerdos, y los efectos ocasionados por cambios en la formulación de la dieta. Con este propósito, fueron llevados a cabo tres estudios. El experimento 1 fue realizado con el objetivo de analizar los factores de variación de la composición de purines y establecer ecuaciones de predicción para emisiones potenciales de NH3 y CH4. Fueron recogidas setenta y nueve muestras de piensos y purines durante dos estaciones del año (verano y invierno) de granjas comerciales situadas en dos regiones de España (Centro y Mediterráneo). Se muestrearon granjas de gestación, maternidad, lactación y cebo. Se determinó la composición de piensos y purines, y la emisión potencial de NH3 y CH4. El contenido de nutrientes de los piensos fue usado como covariable en el análisis. La espectroscopia de reflectancia del infrarrojo cercano (NIRS) se evaluó como herramienta de predicción de la composición y potencial emisión de gases del purín. Se encontró una amplia variabilidad en la composición de piensos y purines. Las granjas del Mediterráneo tenían mayor pH (P<0,001) y concentración de cenizas (P =0,02) en el purín que las del Centro. El tipo de granja también afectó al contenido de extracto etéreo (EE) del purín (P =0,02), observando los valores más elevados en las instalaciones de animales jóvenes. Los resultados sugieren un efecto tampón de la fibra de la dieta en el pH del purín y una relación directa (P<0,05) con el contenido de fibra fecal. El contenido de proteína del pienso no afectó al contenido de nitrógeno del purín, pero disminuyó (P=0,003) la concentración de sólidos totales (ST) y de sólidos volátiles (SV). Se obtuvieron modelos de predicción de la emisión potencial de NH3 (R2=0,89) y CH4 (R2=0,61) partir de la composición del purín. Los espectros NIRS mostraron una buena precisión para la estimación de la mayor parte de los constituyentes, con coeficientes de determinación de validación cruzada (R2cv) superiores a 0,90, así como para la predicción del potencial de emisiones de NH3 y CH4 (R2cv=0,84 y 0,68, respectivamente). El experimento 2 fue realizado para investigar los efectos del nivel de inclusión de dos fuentes de sub-productos fibrosos: pulpa de naranja (PN) y pulpa de algarroba (PA), en dietas iso-fibrosas de cerdos de cebo, sobre la composición del purín y las emisiones potenciales de NH3 y CH4. Treinta cerdos (85,4±12,3 kg) fueron alimentados con cinco dietas iso-nutritivas: control comercial trigo/cebada (C) y cuatro dietas experimentales incluyendo las dos fuentes de sub-productos a dos niveles (75 y 150 g/kg) en una estructura 2 × 2 factorial. Después de 14 días de periodo de adaptación, heces y orina fueron recogidas separadamente durante 7 días para medir la digestibilidad de los nutrientes y el nitrógeno (N) excretado (6 réplicas por dieta) en cerdos alojados individualmente en jaulas metabólicas. Las emisiones de NH3 y CH4 fueron medidas después de la recogida de los purínes durante 11 y 100 días respectivamente. La fuente y el nivel de subproductos fibrosos afectó a la eficiencia digestiva de diferentes formas, ya que los coeficientes de digestibilidad total aparente (CDTA) para la materia seca (MS), materia orgánica (MO), fracciones fibrosas y energía bruta (EB) aumentaron con la PN pero disminuyeron con la inclusión de PA (P<0,05). El CDTA de proteína bruta (PB) disminuyó con la inclusión de las dos fuentes de fibra, siendo más bajo al mayor nivel de inclusión. La concentración fecal de fracciones fibrosas aumentó (P<0,05) con el nivel de inclusión de PA pero disminuyó con el de PN (P<0,01). El nivel más alto de las dos fuentes de fibra en el pienso aumentó (P<0,02) el contenido de PB fecal pero disminuyó el contenido de N de la orina (de 205 para 168 g/kg MS, P<0,05) en todas las dietas suplementadas comparadas con la dieta C. Adicionalmente, las proporciones de nitrógeno indigerido, nitrógeno soluble en agua, nitrógeno bacteriano y endógeno excretado en heces no fueron afectados por los tratamientos. Las características iniciales del purín no difirieron entre las diferentes fuentes y niveles de fibra, excepto para el pH que disminuyó con la inclusión de altos niveles de sub-productos. La emisión de NH3 por kg de purín fue más baja en todas las dietas suplementadas con fibras que en la dieta C (2,44 vs.1,81g de promedio, P<0,05). Además, purines de dietas suplementadas con alto nivel de sub-productos tendieron (P<0,06) a emitir menos NH3 por kg de nitrógeno total y mostraron un potencial más bajo para emitir CH4, independientemente de la fuente de fibra. El experimento 3 investigó los efectos de la fuente de proteína en dietas prácticas. Tres piensos experimentales fueron diseñados para sustituir una mescla de harina y cascarilla de soja (SOJ) por harina de girasol (GIR) o por DDGS del trigo (DDGST). La proporción de otros ingredientes fue modificada para mantener los contenidos de nutrientes similares a través de las dietas. El cambio en la fuente de proteína dio lugar a diferencias en el contenido de fibra neutro detergente ligada a proteína bruta (FNDPB), fibra soluble (FS) y lignina ácido detergente (LAD) en la dieta. Veinticuatro cerdos (ocho por dieta), con 52,3 o 60,8 kg en la primera y segunda tanda respectivamente, fueron alojados individualmente en jaulas metabólicas. Durante un periodo de 7 días fue determinado el balance de MS, el CDTA de los nutrientes y la composición de heces y orina. Se realizó el mismo procedimiento del experimento 2 para medir las emisiones de NH3 y CH4 de los purines de cada animal. Ni la ingestión de MS ni el CDTA de la MS o de la energía fueron diferentes entre las dietas experimentales, pero el tipo de pienso afectó (P<0.001) la digestibilidad de la PB, que fue mayor para GIR (0,846) que para SOJ (0,775), mientras que la dieta DDGST mostró un valor intermedio (0,794). La concentración fecal de PB fue por tanto influenciada (P<0,001) por el tratamiento, observándose la menor concentración de PB en la dieta GIR y la mayor en la dieta SOJ. La proporción de N excretado en orina o heces disminuyó de 1,63 en la dieta GIR hasta 0,650 en la dieta SOJ, como consecuencia de perdidas más bajas en orina y más altas en heces, con todas las fracciones de nitrógeno fecales creciendo en paralelo a la excreción total. Este resultado fue paralelo a una disminución de la emisión potencial de NH3 (g/kg purín) en la dieta SOJ con respecto a la dieta GIR (desde 1,82 a 1,12, P<0,05), dando valores intermedios (1,58) para los purines de la dieta DDGST. Por otro lado, el CDTA de la FS y de la fibra neutro detergente (FND) fueron afectados (P<0,001 y 0,002, respectivamente) por el tipo de dieta, siendo más bajas en la dieta GIR que en la dieta SOJ; además, se observó un contenido más alto de FND (491 vs. 361g/kg) en la MS fecal para la dieta GIR que en la dieta SOJ, presentando la dieta DDGST valores intermedios. El grado de lignificación de la FND (FAD/FND x 100) de las heces disminuyó en el orden GIR>DDGST>SOJ (desde 0,171 hasta 0,109 y 0,086, respectivamente) en paralelo a la disminución del potencial de emisión de CH4 por g de SV del purín (desde 301 a 269 y 256 mL, respectivamente). Todos los purines obtenidos en estos tres experimentos y Antezana et al. (2015) fueron usados para desarrollar nuevas calibraciones con la tecnología NIRS, para predecir la composición del purín y el potencial de las emisiones de gases. Se observó una buena precisión (R2cv superior a 0,92) de las calibraciones cuando muestras de los ensayos controlados (2, 3 y Antezana et al., 2015) fueron añadidas, aumentando el rango de variación. Una menor exactitud fue observada para TAN y emisiones de NH3 y CH4, lo que podría explicarse por una menor homogeneidad en la distribución de las muestras cuando se amplía el rango de variación del estudio. ABSTRACT This PhD thesis was developed to study the emissions of ammonia (NH3) and methane (CH4) from pig slurry and the effects caused by changes on diet formulation. For these proposes three studies were conducted. Experiment 1 aimed to analyse several factors of variation of slurry composition and to establish prediction equations for potential CH4 and NH3 emissions. Seventy-nine feed and slurry samples were collected at two seasons (summer and winter) from commercial pig farms sited at two Spanish regions (Centre and Mediterranean). Nursery, growing-fattening, gestating and lactating facilities were sampled. Feed and slurry composition were determined, and potential CH4 and NH3 emissions measured. Feed nutrient contents were used as covariates in the analysis. Near infrared reflectance spectroscopy (NIRS) was evaluated as a predicting tool for slurry composition and potential gaseous emissions. A wide variability was found both in feed and slurry composition. Mediterranean farms had a higher pH (P<0.001) and ash (P=0.02) concentration than those located at the centre of Spain. Also, type of farm affected ether extract (EE) content of the slurry (P=0.02), with highest values obtained for the youngest animal facilities. Results suggested a buffer effect of dietary fibre on slurry pH and a direct relationship (P<0.05) with fibre constituents of manure. Dietary protein content did not affect slurry nitrogen content (N) but decreased (P=0.003) in total solid (TS) and volatile solids (VS) concentration. Prediction models of potential NH3 emissions (R2=0.89) and biochemical CH4 potential (B0) (R2=0.61) were obtained from slurry composition. Predictions from NIRS showed a high accuracy for most slurry constituents with coefficient of determination of cross validation (R2cv) above 0.90 and a similar accuracy of prediction of potential NH3 and CH4 emissions (R2cv=0.84 and 0.68, respectively) thus models based on slurry composition from commercial farms. Experiment 2 was conducted to investigate the effects of increasing the level of two sources of fibrous by-products, orange pulp (OP) and carob meal (CM), in iso-fibrous diets for growing-finishing pig, slurry composition and potential NH3 and CH4 emissions. Thirty pigs (85.4±12.3 kg) were fed five iso-nutritive diets: a commercial control wheat/barley (C) and four experimental diets including two sources of fibrous by-products OP and CM and two dietary levels (75 and 150 g/kg) in a 2 × 2 factorial arrangement. After a 14-day adaptation period, faeces and urine were collected separately for 7 days to measure nutrient digestibility and the excretory patterns of N from pigs (6 replicates per diet) housed individually in metabolic pens. For each animal, the derived NH3 and CH4 emissions were measured in samples of slurry over an 11 and 100-day storage periods, respectively. Source and level of the fibrous by-products affected digestion efficiency in a different way as the coefficients of total tract apparent digestibility (CTTAD) for dry matter (DM), organic matter (OM), fibre fractions and gross energy (GE) increased with OP but decreased with CM (P<0.05). Crude protein CTTAD decreased with the inclusion of both sources of fibre, being lower at the highest dietary level. Faecal concentration of fibre fractions increased (P<0.05) with the level of inclusion of CM but decreased with that of OP (P<0.01). High dietary level for both sources of fibre increased (P<0.02) CP faecal content but urine N content decreased (from 205 to 168 g/kg DM, P<0.05) in all the fibre-supplemented compared to C diet. Additionally, the proportions of undigested dietary, water soluble, and bacterial and endogenous debris of faecal N excretion were not affected by treatments. The initial slurry characteristics did not differ among different fibre sources and dietary levels, except pH, which decreased at the highest by-product inclusion levels. Ammonia emission per kg of slurry was lower in all the fibre-supplemented diets than in C diet (2.44 vs. 1.81g as average, P<0.05). Additionally, slurries from the highest dietary level of by-products tended (P<0.06) to emit less NH3 per kg of initial total Kjeldahl nitrogen (TKN) and showed a lower biochemical CH4 potential , independently of the fibre source. Experiment 3 investigated the effects of protein source in practical diets. Three experimental feeds were designed to substitute a mixture of soybean meal and soybean hulls (SB diet) with sunflower meal (SFM) or wheat DDGS (WDDGS). The proportion of other ingredients was also modified in order to maintain similar nutrient contents across diets. Changes in protein source led to differences in dietary content of neutral detergent insoluble crude protein (NDICP), soluble fibre (SF) and acid detergent lignin (ADL). Twenty-four pigs (eight per diet), weighing 52.3 or 60.8 kg at the first and second batch respectively, were housed individually in metabolic pens to determine during a 7-day period DM balance, CTTAD of nutrients, and faecal and urine composition. Representative slurry samples from each animal were used to measure NH3 and CH4 emissions over an 11 and or 100-day storage period, respectively. Neither DM intake, nor DM or energy CTTAD differed among experimental diets, but type of feed affected (P<0.001) CP digestibility, which was highest for SFM (0.846) than for SB (0.775) diet, with WDDGS-based diet giving an intermediate value (0.794). Faecal DM composition was influenced (P<0.001) accordingly, with the lowest CP concentration found for diet SFM and the highest for SB. The ratio of N excreted in urine or faeces decreased from SFM (1.63) to SB diet (0.650), as a consequence of both lower urine and higher faecal losses, with all the faecal N fractions increasing in parallel to total excretion. This result was parallel to a decrease of potential NH3 emission (g/kg slurry) in diet SB with respect to diet SFM (from 1.82 to 1.12, P<0.05), giving slurry from WDDGS-based diet an intermediate value (1.58). Otherwise, SF and insoluble neutral detergent fibre (NDF) CTTAD were affected (P<0.001 and P=0.002, respectively) by type of diet, being lower for SFM than in SB-diet; besides, a higher content of NDF (491 vs. 361 g/kg) in faecal DM was observed for SFM with respect to SB based diet, with WDDGS diet being intermediate. Degree of lignification of NDF (ADL/NDF x 100) of faeces decreased in the order SFM>WDDGS>SB (from 0.171 to 0.109 and 0.086, respectively) in parallel to a decrease of biochemical CH4 potential per g of VS of slurry (from 301 to 269 and 256 ml, respectively). All slurry samples obtained from these three experiments and Antezana et al. (2015) were used to develop new calibrations with NIRS technology, to predict the slurry composition and potential gaseous emissions of samples with greater variability in comparison to experiment 1. Better accuracy (R2cv above 0.92) was observed for calibrations when samples from controlled trials experiments (2, 3 and Antezana et al., 2015) were included, increasing the range of variation. A lower accuracy was observed for TAN, NH3 and CH4 gaseous emissions, which might be explained by the less homogeneous distribution with a wider range of data.