Procedure for verification of sound source coverage over façades according to the International Standard ISO 140-5

This paper presents a new verification procedure for sound source coverage according to ISO 140?5 requirements. The ISO 140?5 standard applies to the measurement of façade insulation and requires a sound source able to achieve a sufficiently uniform sound field in free field conditions on the façade under study. The proposed method involves the electroacoustic characterisation of the sound source in laboratory free field conditions (anechoic room) and the subsequent prediction by computer simulation of the sound free field radiated on a rectangular surface equal in size to the façade being measured. The loudspeaker is characterised in an anechoic room under laboratory controlled conditions, carefully measuring directivity, and then a computer model is designed to calculate the acoustic free field coverage for different loudspeaker positions and façade sizes. For each sound source position, the method provides the maximum direct acoustic level differences on a façade specimen and therefore determines whether the loudspeaker verifies the maximum allowed level difference of 5 dB (or 10 dB for façade dimensions greater than 5 m) required by the ISO standard. Additionally, the maximum horizontal dimension of the façade meeting the standard is calculated and provided for each sound source position, both with the 5 dB and 10 dB criteria. In the last section of the paper, the proposed procedure is compared with another method used by the authors in the past to achieve the same purpose: in situ outdoor measurements attempting to recreate free field conditions. From this comparison, it is concluded that the proposed method is able to reproduce the actual measurements with high accuracy, for example, the ground reflection effect, at least at low frequencies, which is difficult to avoid in the outdoor measurement method, and it is fully eliminated with the proposed method to achieve the free field requisite.

Influence of loudspeaker directivity and measurement geometry on direct acoustic levels over façades for acoustic insulation tests with the International Standard ISO 140-5

The International Standard ISO 140-5 on field measurements of airborne sound insulation of façades establishes that the directivity of the measurement loudspeaker should be such that the variation in the local direct sound pressure level (ΔSPL) on the sample is ΔSPL < 5 dB (or ΔSPL < 10 dB for large façades). This condition is usually not very easy to accomplish nor is it easy to verify whether the loudspeaker produces such a uniform level. Direct sound pressure levels on the ISO standard façade essentially depend on the distance and directivity of the loudspeaker used. This paper presents a comprehensive analysis of the test geometry for measuring sound insulation and explains how the loudspeaker directivity, combined with distance, affects the acoustic level distribution on the façade. The first sections of the paper are focused on analysing the measurement geometry and its influence on the direct acoustic level variations on the façade. The most favourable and least favourable positions to minimise these direct acoustic level differences are found, and the angles covered by the façade in the reference system of the loudspeaker are also determined. Then, the maximum dimensions of the façade that meet the conditions of the ISO 140-5 standard are obtained for the ideal omnidirectional sound source and the piston radiating in an infinite baffle, which is chosen as the typical radiation pattern for loudspeakers. Finally, a complete study of the behaviour of different loudspeaker radiation models (such as those usually utilised in the ISO 140-5 measurements) is performed, comparing their radiation maps on the façade for searching their maximum dimensions and the most appropriate radiation configurations.

Estudio y análisis para la elaboración de un modelo de certificado de calidad cinegética en España = Study and analysis for the development of a model of hunting quality certificate in Spain

Con esta tesis doctoral se pretende elaborar un modelo de Certificado de Calidad Cinegética independiente, de adhesión voluntaria y aplicable a todo tipo de espacios cinegéticos, de forma que posteriormente pueda convertirse en una metodología que sea empleada como instrumento válido de medición de la Calidad Cinegética y normalizada a través de una familia de Normas aprobadas por un organismo de normalización reconocido a nivel nacional o internacional. En primer lugar, se procedió a la realización de un riguroso y exhaustivo estudio de justificación siguiendo la metodología propuesta por la Norma UNE 66172:2003 IN, Directrices para la justificación y desarrollo de sistemas de gestión (equivalente a la Norma Internacional GUIA ISO/IEC 72:2001). A continuación, se procedió a la identificación y desarrollo de los parámetros de Ordenación Cinegética comunes a cualquier espacio cinegético en España y a la conceptualización de la Calidad Cinegética. Finalmente, se desarrolló un modelo estructurado en nueve Criterios y treinta y cuatro Indicadores de Calidad Cinegética, y un proyecto de familia de Normas para la Certificación de la Calidad Cinegética. ABSTRACT This doctoral thesis aims to produce a model of Hunting Quality Certificate independent, of voluntary adherence and applicable to all types of hunting areas, so that later it can become a methodology to be used as a valid instrument for measuring Hunting Quality and standardized through a family of standards approved by an organization of standardization recognized at a national or an international level. First, we proceeded to carry out a rigorous and comprehensive justification study following the methodology proposed by the UNE 66172: 2003 IN, Guidelines for the justification and development of management systems standards (equivalent to the International Standard GUIA ISO / IEC 72: 2001). Then, we proceeded to the identification and development of Hunting Management parameters common to any hunting area in Spain and the conceptualization of Hunting Quality. Finally, a model structured into nine Criteria and thirty-four Indicators of Hunting Quality and a draft of a family of standards for Hunting Quality Certification were developed.

Analysis of the geometric altimetry to support aircraft optimal profiles within future 4D trajectory management

The use of barometric altimetry is to some extent a limiting factor on safety, predictability and efficiency of aircraft operations, and reduces the potential of the trajectory based operations capabilities. However, geometric altimetry could be used to improve all of these aspects. Nowadays aircraft altitude is estimated by applying the International Standard Atmosphere which differs from real altitude. At different temperatures for an assigned barometric altitude, aerodynamic forces are different and this has a direct relationship with time, fuel consumption and range of the flight. The study explores the feasibility of using sensors providing geometric reference altitude, in particular, to supply capabilities for the optimization of vertical profiles and also, their impact on the vertical Air Traffic Management separation assurance processes. One of the aims of the thesis is to assess if geometric altitude fulfils the aeronautical requirements through existing sensors. Also the thesis will elaborate on the advantages of geometric altitude over the barometric altitude in terms of efficiency for vertical navigation. The evidence that geometric altitude is the best choice to improve the efficiency in vertical profile and aircraft capacity by reducing vertical uncertainties will also be shown. In this paper, an atmospheric study is presented, as well as the impact of temperature deviation from International Standard Atmosphere model is analyzed in order to obtain relationship between geometric and barometric altitude. Furthermore, an aircraft model to study aircraft vertical profile is provided to analyse trajectories based on geometric altitudes.

A Process Asset Library to support Software Process Improvement in Small Settings

A main factor to the success of any organization process improvement effort is the Process Asset Library implementation that provides a central database accessible by anyone at the organization. This repository includes any process support materials to help process deployment. Those materials are composed of organization's standard software process, software process related documentation, descriptions of the software life cycles, guidelines, examples, templates, and any artefacts that the organization considers useful to help the process improvement. This paper describe the structure and contents of the Web-based Process Asset Library for Small businesses and small groups within large organizations. This library is structured using CMMI as reference model in order to implement those Process Areas described by this model.

Procedimiento para la medición y verificación de la directividad y la cobertura de una fuente sobre un elemento de fachada de acuerdo a la norma ISO 140-5

El apartado <4.2 Altavoz> de la Norma Internacional UNE-EN ISO 140-5 [1] especifica que la directividad del altavoz usado en el ensayo debe asegurar en todas las bandas de frecuencias de interés, unas diferencias de nivel locales inferiores a 5dB (o a 10 dB para fachadas de dimensiones mayores a 5m), medidas en campo libre, sobre una superficie del mismo tamaño y orientación que la pared o elemento a ensayar. Este requisito debe verificarse en unas bandas de frecuencia de interés que sean como mínimo los tercios de octava desde 100Hz hasta 3150Hz, y preferiblemente desde 50Hz hasta 5kHz. Desde hace unos años, en el Laboratorio de sonido de la EUIT de Telecomunicación de la Universidad Politécnica de Madrid, los autores han implementado un método en el que, a partir de las medidas de directividad en cámara anecoica de la fuente sonora a ensayar, se calcula el campo sonoro directo sobre una superficie ficticia que representa un elemento de fachada en la misma disposición que se indica en la norma ICO 140-5 y con unas dimensiones según se requieran en el procedimiento. También se estima la dimensión horizontal máxima ΔXmax de una fachada rectangular en relación de aspecto fija que permite verificar la norma con los criterios de 5dB y 10dB de diferencias máximas de niveles directos en dicha fachada. En esta ponencia se detalla el procedimiento anterior. ABSTRACT. The Section "4.2 loudspeaker" of the UNE-EN ISO 140-5 International Standard: "Field measurements of airborne sound insulation of façade elements and façades", specifies that the directivity of the loudspeaker used in the test must ensure in all frequency bands of interest, local level differences less than 5dB (or 10dB for façade dimensions greater than 5m), measured in free field over an area of the same size and orientation as the wall or element to be tested. This requirement must be verified in the frequency bands of interest which are, at least, the third octave bands from 100Hz to 3150Hz, preferably from 50Hz to 5kHz. In recent years, in the Laboratory of Sound of the EUIT Telecomunicación (Universidad Politécnica de Madrid), the authors have implemented a method that, from directivity measurements of loudspeakers performed in the anechoic room, the direct sound field on a surface in the same layout as indicated in the ISO standard is calculated. It is also estimated the maximum horizontal dimension Δxmax of a rectangular façade for each aspect ratio which verify the standard criteria of either 5dB or 10dB for the maximum differences of direct levels in the façade. This paper details the procedure above introduced.

Ensayos de seguridad eléctrica orientados a la vigilancia del mercado

El presente estudio recopila los diferentes bancos de pruebas de EMC, Radio, SAR y seguridad eléctrica que se utiliza en la vigilancia del mercado. Describe las pruebas realizadas por el Estado español para llevar a cabo el seguimiento y control de los equipos vendidos. En primer lugar se presenta una descripción cualitativa de los ambientes clasificados por requisitos que explica en qué consisten las pruebas que se hacen, cómo se configura el entorno de medida y cuáles son los equipos que se deben utilizar. Está ilustrado con fotografías de los bastidores, antenas, amplificadores, generadores y otros equipos que la SETSI tiene en su laboratorio en El Casar (Guadalajara). La vigilancia de los equipos se realiza periódicamente en los estados miembros de la Unión Europea. Los funcionarios responsables también se reúnen periódicamente a nivel europeo para sacar conclusiones y hacer proyecciones futuras. El equipo adquirido en centros comerciales de venta al público, después de poco más de un mes, en el que se pasan las pruebas, vuelve a la cadena de comercialización, por lo que los dispositivos no se puedan dañar. Las pruebas realizadas en el laboratorio no pueden ser perjudiciales para los dispositivos por lo que es necesario tomar precauciones en la ejecución de las pruebas. El centro del PFC es el área de la Seguridad Eléctrica. El capítulo 4 es una reproducción de la Norma internacional IEC 60950-1:2007/A11 sobre seguridad en equipos de tecnología de la información adaptada a los requisitos de la vigilancia de mercado. Las autoridades competentes se basan en este estándar para evaluar y garantizar la seguridad del usuario en los equipos de consumo. Diseñados los procedimientos de ensayo y montado un banco de acuerdo a estos ensayos, se ha preparado un manual de operador, capítulo 5, en el que se recogen cada una de las pruebas y controles visuales que deben realizarse para probar que el equipo es conforme. Para finalizar, en el capítulo 6, se ejecutan ensayos de ejemplo sobre tres dispositivos de prueba y se elaboran las correspondientes hojas de ensayo. El propósito es proporcionar al operador un manual completo del banco de seguridad eléctrica, es por ello que en el manual de operador se han repetido muchos fragmentos de la norma para facilitar al operador el objetivo concreto de las pruebas y el acceso fácil a la información. This dissertation presents the different test benches of EMC, Radio, SAR and Electrical Safety that are used in market surveillance. Describes the tests performed by the Spanish State to carry out the monitoring and control of equipment sold. First a qualitative description of the environments classified by requisites that explains in that consist the tests that are make it, how it configures the measure environment and which are the equipment that it should use. It is illustrated with photographs of the racks, antennas, amplifiers, generators and other equipment that the S.E.T.S.I has in its laboratory on El Casar (Guadalajara). The surveillance of equipment is performed periodically in the member states of the European Union. Responsible officials also periodically meet at European level to draw conclusions and make future projections. The equipment purchased in malls public sale, after little more than a month, in which the tests are passed, returned to the trade chain, which is why the devices cannot be damaged. The tests done in the laboratory may not be harmful for devices are thus necessary to take precautions in the execution of the tests. The center of this dissertation is the area of Electrical Safety. Chapter 4 is a reproduction of the International Standard IEC 60950-1:2007/A11 safety in teams of information technology, adapted to the requirements of market surveillance. The competent authorities are based on this standard to assess and ensure the user's safety in the consumption equipment. Designed test procedures and mounted on a bench according to these tests, it has prepared a manual operator, in Chapter 5, with each of the tests and visual inspections in order to prove that the equipment complies. Finally, in Chapter 6, such tests run on three devices are developed test and test some leaves. The purpose of this book is to provide an operator manual of the bench of electrical safety, which is why the operator manual have been repeated fragments of the standard, in chapter 5, to facilitate the operator to test execution and access to information.

Design, implementation and evaluation of an unconstrained and contactless biometric system based on hand geometry and stress detection

Esta tesis propone un sistema biométrico de geometría de mano orientado a entornos sin contacto junto con un sistema de detección de estrés capaz de decir qué grado de estrés tiene una determinada persona en base a señales fisiológicas Con respecto al sistema biométrico, esta tesis contribuye con el diseño y la implementación de un sistema biométrico de geometría de mano, donde la adquisición se realiza sin ningún tipo de contacto, y el patrón del usuario se crea considerando únicamente datos del propio individuo. Además, esta tesis propone un algoritmo de segmentación multiescala para solucionar los problemas que conlleva la adquisición de manos en entornos reales. Por otro lado, respecto a la extracción de características y su posterior comparación esta tesis tiene una contribución específica, proponiendo esquemas adecuados para llevar a cabo tales tareas con un coste computacional bajo pero con una alta precisión en el reconocimiento de personas. Por último, este sistema es evaluado acorde a la norma estándar ISO/IEC 19795 considerando seis bases de datos públicas. En relación al método de detección de estrés, esta tesis propone un sistema basado en dos señales fisiológicas, concretamente la tasa cardiaca y la conductancia de la piel, así como la creación de un innovador patrón de estrés que recoge el comportamiento de ambas señales bajo las situaciones de estrés y no-estrés. Además, este sistema está basado en lógica difusa para decidir el grado de estrés de un individuo. En general, este sistema es capaz de detectar estrés de forma precisa y en tiempo real, proporcionando una solución adecuada para sistemas biométricos actuales, donde la aplicación del sistema de detección de estrés es directa para evitar situaciónes donde los individuos sean forzados a proporcionar sus datos biométricos. Finalmente, esta tesis incluye un estudio de aceptabilidad del usuario, donde se evalúa cuál es la aceptación del usuario con respecto a la técnica biométrica propuesta por un total de 250 usuarios. Además se incluye un prototipo implementado en un dispositivo móvil y su evaluación. ABSTRACT: This thesis proposes a hand biometric system oriented to unconstrained and contactless scenarios together with a stress detection method able to elucidate to what extent an individual is under stress based on physiological signals. Concerning the biometric system, this thesis contributes with the design and implementation of a hand-based biometric system, where the acquisition is carried out without contact and the template is created only requiring information from a single individual. In addition, this thesis proposes an algorithm based on multiscale aggregation in order to tackle with the problem of segmentation in real unconstrained environments. Furthermore, feature extraction and matching are also a specific contributions of this thesis, providing adequate schemes to carry out both actions with low computational cost but with certain recognition accuracy. Finally, this system is evaluated according to international standard ISO/IEC 19795 considering six public databases. In relation to the stress detection method, this thesis proposes a system based on two physiological signals, namely heart rate and galvanic skin response, with the creation of an innovative stress detection template which gathers the behaviour of both physiological signals under both stressing and non-stressing situations. Besides, this system is based on fuzzy logic to elucidate the level of stress of an individual. As an overview, this system is able to detect stress accurately and in real-time, providing an adequate solution for current biometric systems, where the application of a stress detection system is direct to avoid situations where individuals are forced to provide the biometric data. Finally, this thesis includes a user acceptability evaluation, where the acceptance of the proposed biometric technique is assessed by a total of 250 individuals. In addition, this thesis includes a mobile implementation prototype and its evaluation.

Consultoría en el marco económico-financiero de la empresa

Muchas de las grandes iniciativas empresariales, se ven truncadas por falta de un adecuado análisis económico-financiero. Incluso, muchas grandes ideas no son implantadas correctamente en el primer intento por este motivo, y son otras personas las que consiguen posteriormente el éxito de esas brillantes ideas gracias a una correcta aproximación financiera. Las empresas necesitan definir sus objetivos, establecer las para lograrlos, identificar las personas responsables de su ejecución (sus roles y funciones) y elaborar un plan económico-financiero que recoja el estudio de inversiones necesarias, el análisis de costes, la previsión de ingresos, así como la estrategia financiera más adecuada para la captación de los fondos necesarios para llevar a cabo las acciones programadas. Una vez iniciado el proyecto empresarial, será imprescindible realizar un seguimiento y control de la evolución (integración), tomando las medidas que se estimen oportunas para mantener el rumbo adecuado durante todo el tiempo de actividad. En este trabajo, aplicaremos las metodologías y buenas prácticas de la gestión de proyectos, como marco estructurado que nos permita abordar las principales cuestiones económico-financieras a tener en cuenta a la hora de enfrentarnos a un proyecto empresarial, para contribuir, en la medida de lo posible, a que los emprendedores tengan en cuenta estas cuestiones, facilitando así el desarrollo de negocios, en un difícil entorno económico de crisis como el que actualmente estamos viviendo en España, y animando de esta manera a optar por la iniciativa emprendedora, tratando de minimizar el riesgo en base al contenido. ---ABSTRACT---Lack of adequate economic and financial analysis truncates many of the entrepreneurship and innovation programs. Because of that reason, many great ideas are not even correctly implemented on the first attempt, and the person who finds the proper financial approach, succeed. All the enterprises have to establish clear objectives, actions to accomplish those objectives, assign roles, responsibilities and executive functions to specific people. Elaborate funding plan that contains surveys on necessary investments, cost analysis, estimate the income, liquid assets and also financial strategy suitable for fundraising to finance programmed actions. Once the project has been executed it is essential to monitor and control the development and integration adopting measures accordingly to the needs. This thesis applies methodology and best practice of project management as structured framework for the principal economic and financial issues facing business project. It is necessary contribution to entrepreneurs understanding of business, therefore facilitates business development in such rough environment as Spain is at this moment, and at the same time encourages adopting entrepreneur’s solution as less risky one. This document aims to explore all the economic and financial issues from methodological point of view based on my own professional experience, resulting in helping to understand the importance that economy and finances have in developing adequate corporate strategy. Crisis has highlighted inadequate functionality of many companies. Most popular first symptom is lack of cash flow that deteriorates the company, and results in suspension of payments followed by closing. In other cases, difficulties appear due to poor financial management of committed resources; to be observed in lack of prevision and planning or incorrect basic functionality and operational matters on daily basis. What would be your advice to someone who have magnificent business idea however no knowledge on how to handle finances in order to succeed in initiating and executing the project? Despite of the fact that the central nucleus of this paper is at economics and finances area, all the other concepts and topics given during master will be revived; for example business strategy, consultants abilities, organization and standard processes, among others, are impregnated with knowledge of project management.

Diseño e implementación de librería funcional para lectura y control remoto de contadores eléctricos de última generación

El siguiente trabajo explora en primer lugar el protocolo de transmisión de datos IEC 870-5-102,el cual está definido como un estándar internacional para la transmisión de totales integrados, más tarde analizaremos su aplicación en un sistema de lectura de contadores eléctricos en remoto. Este protocolo de transmisión de datos para tele-lectura nos ayuda a solventar el problema en la construcción de un sistema de lectura para contadores eléctricos. ABSTRACT This paper explored the IEC 870-5-102 transmission protocol firstly, which is the international standard for the transmission of integrated totals, and then analyze its insufficiencies in the application of electric remote-metering system. The data transmission protocol of energy remote-metering system solves the problems in the construction of an implementation for metering the information inside meters.

Generación automática de la configuración de subestaciones eléctricas según el Estándar IEC 61850 a partir de una herramienta de diseño gráfico

La evolución de las redes eléctricas se dirige hacia lo que se conoce como “Smart Grids” o “Redes Eléctricas Inteligentes”. Estas “Smart Grids” se componen de subestaciones eléctricas, que a su vez se componen de unos dispositivos llamados IEDs (Dispositivos Electrónicos Inteligentes – Intelligent Electronic Devices). El diseño de IEDs se encuentra definido en la norma IEC 61850, que especifica además un Lenguaje de Configuración de Subestaciones (Substation Configuration Language SCL) para la definición de la configuración de subestaciones y sus IEDs. Hoy en día, este estándar internacional no sólo se utiliza para diseñar correctamente IEDs y asegurar su interoperabilidad, sino que también se utiliza para el diseño de otros dispositivos de la red eléctrica, como por ejemplo, medidores inteligentes. Sin embargo, aunque existe una tendencia cada vez mayor del uso de este estándar, la comprensión y el manejo del mismo resulta difícil debido al gran volumen de información que lo compone y del nivel de detalle que utiliza, por lo que su uso para el diseño de IEDs se hace tedioso sin la ayuda de un soporte software. Es por ello que, para facilitar la aplicación del estándar IEC 61850 en el diseño de IEDs se han desarrollado herramientas como “Visual SCL”, “SCL Explorer” o “61850 SCLVisual Design Tool”. En concreto, “61850 SCLVisual Design Tool” es una herramienta gráfica para el modelado de subestaciones electricas, generada mediante el uso de los frameworks Eclipse Modeling Framework (EMF) y Epsilon Generative Modeling Technologies (GMT) y desarrollada por el grupo de investigación SYST de la UPM. El objetivo de este proyecto es añadir una nueva funcionalidad a la herramienta “61850 Visual SCL DesignTool”. Esta nueva funcionalidad consiste en la generación automática de un fichero de configuración de subestaciones eléctricas según el estándar IEC 61850 a partir de de una herramienta de diseño gráfico. Este fichero, se denomina SCD (Substation Configuration Description), y se trata de un fichero XML conforme a un esquema XSD (XML Schema Definition) mediante el que se define el lenguaje de configuración de subestaciones SCL del IEC 61850. Para el desarrollo de este proyecto, es necesario el estudio del lenguaje para la configuración de subestaciones SCL, así como del lenguaje gráfico específico de dominio definido por la herramienta “61850 SCLVisual Design Tool”, la estructura de los ficheros SCD, y finalmente, del lenguaje EGL (Epsilon Generation Language) para la transformación y generación automática de código a partir de modelos EMF. ABSTRACT Electrical networks are evolving to “Smart Grids”. Smart Grids are composed of electrical substations that in turn are composed of devices called IEDs (Intelligent Electronic Devices). The design of IEDs is defined by the IEC 61850 standard, which also specifies a Substation Configuration Languaje (SCL) used to define the configuration of substations and their IEDs. Nowadays, this international standard is not only used to design properly IEDs and guarantee their interoperability, but it is also used to design different electrical network devices, such as, smart meters. However, although the use of this standard is growing, its compression as well as its management, is still difficult due to its large volume of information and its level of detail. As a result, designing IEDs becomes a tedious task without a software support. As a consequence of this, in order to make easier the application of the IEC 61850 standard while designing IEDs, some software tools have been developed, such as: “Visual SCL”, “SCL Explorer” or “61850 SCLVisual Design Tool”. In particular, “61850 SCLVisual Design Tool” is a graphical tool used to make electrical substations models, and developed with the Eclipse Modeling Framework (EMF) and Epsilon Generative Modeling Technologies (GMT) by the research group SYST of the UPM. The aim of this project is to add a new functionality to “61850 Visual SCL DesignTool”. This new functionality consists of the automatic code generation of a substation configuration file according to the IEC 61850 standard. This file is called SCD (Substation Configuration Description), and it is a XML file that follows a XSD (XML Schema Definition) that defines the Substation Configuration Language (SCL) of the IEC 61850. In order to develop this project, it is necessary to study the Substation Configuration Language (SCL), the domain-specific graphical languaje defined by the tool “61850 SCLVisual Design Tool”, the structure of a SCD file, and the Epsilon Generation Language (EGL) used for the automatic code generation from EMF models

Visual grading of large cross section structural timber of Pinus sylvestris L. according to UNE 56544:2007 standard

Large cross section structural timber have been used in many structures over long periods of time and still make up an important part of the market due to its mechanical properties. Furthermore, it is frequent its employment in new construction site. It involves the need for a visual grading standard for timber used in construction according to the quality assessment. The material has to satisfy the requirements according to the currently regulations. UNE 56544 is the Spanish visual grading standard for coniferous structural timber. The 2007 version defined a new visual grade in the standard for large section termed Structural Large Timber (MEG). This research checks the new visual grading and consists of 116 structural size specimens of sawn coniferous timber of Scotch pine (Pinus sylvestris L.) from Segovia, Spain. The pieces had a cross section of 150 by 200 mm. They were visually graded according to UNE 56544:2007. Also, mechanical properties have been obtained according to standard EN 408. The results show very low output with an excessive percentage of rejected pieces (33%). The main reasons for the rejection of pieces are fissures and twist

Services Between Video Producers and Broadcasters: Do we need a standard?

Se muestra la necesidad de la creación de un estándar que facilite el intercambio de datos entre empresas productoras de vídeo y cadenas de distribución. Se muestra un posible modelo en la forma de transmisión, modelo de datos y procesado de datos.

Multivariant non-failure analysis via standard abstract interpretation

Non-failure analysis aims at inferring that predicate calis in a program will never fail. This type of information has many applications in functional/logic programming. It is essential for determining lower bounds on the computational cost of calis, useful in the context of program parallelization, instrumental in partial evaluation and other program transformations, and has also been used in query optimization. In this paper, we re-cast the non-failure analysis proposed by Debray et al. as an abstract interpretation, which not only allows to investígate it from a standard and well understood theoretical framework, but has also several practical advantages. It allows us to incorpórate non-failure analysis into a standard, generic abstract interpretation engine. The analysis thus benefits from the fixpoint propagation algorithm, which leads to improved information propagation. Also, the analysis takes advantage of the multi-variance of the generic engine, so that it is now able to infer sepárate non-failure information for different cali patterns. Moreover, the implementation is simpler, and allows to perform non-failure and covering analyses alongside other analyses, such as those for modes and types, in the same framework. Finally, besides the precisión improvements and the additional simplicity, our implementation (in the Ciao/CiaoPP multiparadigm programming system) also shows better efRciency.

New broadband thermal noise primary standard in coaxial technology

A broadband primary standard for thermal noise measurements is presented and its thermal and electromagnetic behavior is analyzed by means of analytical and numerical simulation techniques. It consists of a broadband termination connected to a 3.5mm coaxial airline partially immersed in liquid Nitrogen. The main innovative part of the device is the thermal bead between inner and outer conductors, designed for obtaining a proper thermal contact and to keep low both its contribution to the total thermal noise and its reflectivity. A sensitivity analysis is realized in order to fix the manufacturing tolerances for a proper performance in the range 10MHz¿26.5GHz.