Effect of Stress Level on the High Temperature Deformation and Fracture Mechanisms of Ti-45Al-2Nb-2Mn-0.8 vol. pct TiB2: An In Situ Experimental Study

The effect of the applied stress on the deformation and crack nucleation and propagation mechanisms of a c-TiAl intermetallic alloy (Ti-45Al-2Nb-2Mn (at. pct)-0.8 vol. pct TiB2) was examined by means of in situ tensile (constant strain rate) and tensile-creep (constant load) experiments performed at 973 K (700 �C) using a scanning electron microscope. Colony boundary cracking developed during the secondary stage in creep tests at 300 and 400 MPa and during the tertiary stage of the creep tests performed at higher stresses. Colony boundary cracking was also observed in the constant strain rate tensile test. Interlamellar ledges were only found during the tensile-creep tests at high stresses (r>400 MPa) and during the constant strain rate tensile test. Quantitative measurements of the nature of the crack propagation path along secondary cracks and along the primary crack indicated that colony boundaries were preferential sites for crack propagation under all the conditions investigated. The frequency of interlamellar cracking increased with stress, but this fracture mechanism was always of secondary importance. Translamellar cracking was only observed along the primary crack.

Mechanical behavior and failure micromechanisms of hybrid 3D woven composites in tension

The deformation and failure micromechanisms of a hybrid 3D woven composite were studied in tension. Plain and open-hole composite coupons were tested in tension until failure in the fill and warp directions, as well as fiber tows extracted from the dry fabric and impregnated with the matrix. The macroscopic evolution of damage in the composite coupons was assessed by means of periodic unloading–reloading (to obtain the elastic modulus and the residual strain), whereas the microscopic mechanism were established by means of X-ray computed microtomography. To this end, specimens were periodically removed from the mechanical testing machine and infiltrated with ZnI-containing liquid to assess the main damage modes as a function of the applied strain. The experimental observations and the predictions of an isostrain model were used to understand the key factors controlling the elastic modulus, strength and notch sensitivity of hybrid 3D woven composites in tension. It was found that the full contribution of the glass fibers to the composite strength was not employed, due to the premature fracture of the carbon fibers, but their presence increased the fracture strain and the energy dissipated during fracture. Thus, hybridization of the 3D woven composite led to a notch-insensitive behavior as demonstrated by open-hole tests

Failure locus of polypropylene nonwoven fabrics under in-plane biaxial deformation

The failure locus, the characteristics of the stress–strain curve and the damage localization patterns were analyzed in a polypropylene nonwoven fabric under in-plane biaxial deformation. The analysis was carried out by means of a homogenization model developed within the context of the finite element method. It provides the constitutive response for a mesodomain of the fabric corresponding to the area associated to a finite element and takes into account the main deformation and damage mechanisms experimentally observed. It was found that the failure locus in the stress space was accurately predicted by the Von Mises criterion and failure took place by the localization of damage into a crack perpendicular to the main loading axis.

Influence of texture on the recrystallization mechanisms in an AZ31 Mg sheet alloy at dynamic rates

An AZ31 rolled sheet alloy has been tested at dynamic strain rates View the MathML source at 250 °C up to various intermediate strains before failure in order to investigate the predominant deformation and restoration mechanisms. In particular, tests have been carried out in compression along the rolling direction (RD), in tension along the RD and in compression along the normal direction (ND). It has been found that dynamic recrystallization (DRX) takes place despite the limited diffusion taking place under the high strain rates investigated. The DRX mechanisms and kinetics depend on the operative deformation mechanisms and thus vary for different loading modes (tension, compression) as well as for different relative orientations between the loading axis and the c-axes of the grains. In particular, DRX is enhanced by the operation of 〈c + a〉 slip, since cross-slip and climb take place more readily than for other slip systems, and thus the formation of high angle boundaries is easier. DRX is also clearly promoted by twinning.

Numerical and experimental study of overtopping and failure of rockfill dams

This paper aims to present and validate a numerical technique for the simulation of the overtopping and onset of failure in rockfill dams due to mass sliding. This goal is achieved by coupling a fluid dynamic model for the simulation of the free surface and through-flow problems, with a numerical technique for the calculation of the rockfill response and deformation. Both the flow within the dam body and in its surroundings are taken into account. An extensive validation of the resulting computational method is performed by solving several failure problems on physical models of rockfill dams for which experimental results have been obtained by the authors.

Mechanical behavior and deformation micromechanisms of polypropylene nonwoven fabrics as a function of temperature and strain rate

The mechanical behavior and the deformation and failure micromechanisms of a thermally-bonded polypropylene nonwoven fabric were studied as a function of temperature and strain rate. Mechanical tests were carried out from 248 K (below the glass transition temperature) up to 383 K at strain rates in the range ≈10−3 s−1 to 10−1 s−1. In addition, individual fibers extracted from the nonwoven fabric were tested under the same conditions. Micromechanisms of deformation and failure at the fiber level were ascertained by means of mechanical tests within the scanning electron microscope while the strain distribution at the macroscopic level upon loading was determined by means of digital image correlation. It was found that the nonwoven behavior was mainly controlled by the properties of the fibers and of the interfiber bonds. Fiber properties determined the nonlinear behavior before the peak load while the interfiber bonds controlled the localization of damage after the peak load. The influence of these properties on the strength, ductility and energy absorbed during deformation is discussed from the experimental observations.

Damage localization and failure locus under biaxial loading in glass-fiber nonwoven felts

The pattern of damage localization and fracture under uniaxial and biaxial tension was studied in glass–fiber nonwoven felts. The analyses were carried out within the framework of the finite-element simulation of plain and notched specimens in which the microstructure of the felt, made up of fiber bundles connected at the cross point through an organic binder, was explicitly represented. Following previous experimental observations, fracture by interbundle decohesion and energy dissipation by frictional sliding between the bundles were included in the model. It was found that the failure path in these materials was controlled by the maximum applied normal stress, regardless of the loading path, and that the failure locus under biaxial tension was well represented by the von Mises failure criteria. The notch sensitivity of the nonwoven felts was limited and the presence of a notch did not modify the failure path.

Multiple attractors, long chaotic transients, and failure in small-world networks of excitable neurons.

We study the dynamical states of a small-world network of recurrently coupled excitable neurons, through both numerical and analytical methods. The dynamics of this system depend mostly on both the number of long-range connections or ?shortcuts?, and the delay associated with neuronal interactions. We find that persistent activity emerges at low density of shortcuts, and that the system undergoes a transition to failure as their density reaches a critical value. The state of persistent activity below this transition consists of multiple stable periodic attractors, whose number increases at least as fast as the number of neurons in the network. At large shortcut density and for long enough delays the network dynamics exhibit exceedingly long chaotic transients, whose failure times follow a stretched exponential distribution. We show that this functional form arises for the ensemble-averaged activity if the failure time for each individual network realization is exponen- tially distributed

Contribution to integration and coordination mechanisms for mobile distributed services in publish/subscribe networks

Esta tesis doctoral está enmarcada en dos diferentes pero complementarias áreas de investigación: las redes de Publicación/Subscripción y los servicios móviles distribuidos. Con el paso de los años las redes de Publicación/Subscripción han ido ofreciendo el soporte de comunicaciones desacopladas y ligeras que a su vez, han mejorado la distribución de la información en muchos escenarios de aplicación como lo son la ejecución de servicios distribuidos en entornos fijos. Los servicios móviles distribuidos han de ser desplegados en ambientes inalámbricos en donde los dispositivos móviles deben confiar en las mismas características que las redes de Publicación/Subscripción han estado ofreciendo a sus contrapartes fijos. En este contexto, una de las líneas de investigación pendientes consiste en cómo tomar ventaja de estas características, y cómo avanzar hacia nuevas soluciones no existentes con el fin de mejorar la integración entre los dispositivos fijos y móviles, y la ejecución de los servicios móviles distribuidos. En esta tesis doctoral se pretende avanzar en los mecanismos de integración y coordinación de los servicios móviles distribuidos en el contexto de las redes de Publicación/Subscripción. Los objetivos específicos de esta disertación están enfocados en lograr la integración de los sistemas de Publicación/Suscripción fijos y móviles, y la pro-visión de una versión de red de Publicación/Subscripción específica y uniforme que cuente con mecanismos de coordinación que mejoren la ejecución de los servicios móviles distribuidos. Los resultados de esta tesis doctoral están enmarcados en una versión específica de una red de Publicación/Subscripción que integra brokers fijos y móviles, y permite una coordinación totalmente desacoplada y mejorada entre dispositivos móviles que ejecutan fragmentos de servicios. Las contribuciones específicas son las siguientes: una nueva arquitectura de broker móvil que he llamado Rendezvous Mobile broker, un modelo abstracto de servicios móviles distribuidos coordinados sobre una red de Publicación/Subscripción, mejoras en los mecanismos de enrutamiento epidémicos para diseminar eventos de control producidos por fragmentos de servicios, una solución para soportar servicios altamente fragmentados y geográficamente dispersos, y finalmente una solución de interconexión entre dos dominios de red basados en Publicación/Subscripción: una red basada en el protocolo PubSubHubbub y otro en una red basada en el Publish/Subscribe Internet Routing Paradigm (PSIRP). Los experimentos llevados a cabo confirman que la versión específica de red de Pu-blicación/Subscripción propuesta incrementa el rendimiento de la red en términos de tiempo de espera entre nodos finales, permite una coordinación de los servicios móviles distribuidos más resistente a interrupciones y un mejor uso de los recursos de red, y finalmente logra exitosamente, con variaciones mínimas en el rendimiento de las comunicaciones, la interconexión entre estos dominios de Publicación/Subscripción diferentes. ABSTRACT This dissertation is made up of two different but complementary research areas: Publish/Subscribe networks and mobile distributed services. Over the years, Publish/Subscribe networks have been offering the lightweight and decoupled communication characteristics to improve the information distribution in several application domains such as the execution of distributed services. Mobile distributed services are set to be deployed in wireless environments where mobile devices must rely on the same features Publish/Subscribe networks can offer; so one of the pending research directions consists of how to take advantage of these features and further advance to-wards new un-existing solutions that enhance the integration between mobile and fixed systems and the execution of mobile distributed services. This dissertation seeks to advance the integration and coordination mechanisms of mobile distributed services in the context of Publish/Subscribe networks. The specific objectives aim to enable the integration of mobile and fixed Publish/Subscribe systems and provide a uniform and specific version of a Publish/Subscribe network with new coordination mechanisms that improve the execution of mobile distributed services. The results of this dissertation are enclosed in one specific version of a Publish/Subscribe network that integrates mobile and fixed brokers and coordinates the execution of mobile distributed services. These specific contributions are: a new architecture of a mobile broker I called Rendezvous Mobile Broker, an abstract model for coordinating mobile distributed services executions using a Publish/Subscribe net-work, new gossip routing solutions to disseminate events of services, mechanisms to support highly partitioned and geographically dispersed services and finally, an inter-networking solution between two Publish/Subscribe domains: a PubSubHubbub-based network and the Publish/Subscribe Internet Routing Paradigm (PSIRP)-based network. The experimental efforts confirm that the specific version of the Publish/Subscribe proposed in this dissertation improves the performance of the overall network in terms of end-to-end delay, enables a more resilience execution of mobile distributed services, a better usage of the existing network resources, and finally successfully achieves, with minor variations in the network performance, the internetworking between two different Publish/Subscribe domains.

Automatic quantification of matrix cracking and fiber rotation by X-ray computed tomography in shear-deformed carbon fiber-reinforced laminates

The deformation and damage mechanisms of carbon fiber-reinforced epoxy laminates deformed in shear were studied by means of X-ray computed tomography. In particular, the evolution of matrix cracking, interply delamination and fiber rotation was ascertained as a function of the applied strain. In order to provide quantitative information, an algorithm was developed to automatically determine the crack density and the fiber orientation from the tomograms. The investigation provided new insights about the complex interaction between the different damage mechanisms (i.e. matrix cracking and interply delamination) as a function of the applied strain, ply thickness and ply location within the laminate as well as quantitative data about the evolution of matrix cracking and fiber rotation during deformation

High fidelity simulations of failure in fiber-reinforced composites

Los ensayos virtuales de materiales compuestos han aparecido como un nuevo concepto dentro de la industria aeroespacial, y disponen de un vasto potencial para reducir los enormes costes de certificación y desarrollo asociados con las tediosas campañas experimentales, que incluyen un gran número de paneles, subcomponentes y componentes. El objetivo de los ensayos virtuales es sustituir algunos ensayos por simulaciones computacionales con alta fidelidad. Esta tesis es una contribución a la aproximación multiescala desarrollada en el Instituto IMDEA Materiales para predecir el comportamiento mecánico de un laminado de material compuesto dadas las propiedades de la lámina y la intercara. La mecánica de daño continuo (CDM) formula el daño intralaminar a nivel constitutivo de material. El modelo de daño intralaminar se combina con elementos cohesivos para representar daño interlaminar. Se desarrolló e implementó un modelo de daño continuo, y se aplicó a configuraciones simples de ensayos en laminados: impactos de baja y alta velocidad, ensayos de tracción, tests a cortadura. El análisis del método y la correlación con experimentos sugiere que los métodos son razonablemente adecuados para los test de impacto, pero insuficientes para el resto de ensayos. Para superar estas limitaciones de CDM, se ha mejorado la aproximación discreta de elementos finitos enriqueciendo la cinemática para incluir discontinuidades embebidas: el método extendido de los elementos finitos (X-FEM). Se adaptó X-FEM para un esquema explícito de integración temporal. El método es capaz de representar cualitativamente los mecanismos de fallo detallados en laminados. Sin embargo, los resultados muestran inconsistencias en la formulación que producen resultados cuantitativos erróneos. Por último, se ha revisado el método tradicional de X-FEM, y se ha desarrollado un nuevo método para superar sus limitaciones: el método cohesivo X-FEM estable. Las propiedades del nuevo método se estudiaron en detalle, y se concluyó que el método es robusto para implementación en códigos explícitos dinámicos escalables, resultando una nueva herramienta útil para la simulación de daño en composites. Virtual testing of composite materials has emerged as a new concept within the aerospace industry. It presents a very large potential to reduce the large certification costs and the long development times associated with the experimental campaigns, involving the testing of a large number of panels, sub-components and components. The aim of virtual testing is to replace some experimental tests by high-fidelity numerical simulations. This work is a contribution to the multiscale approach developed in Institute IMDEA Materials to predict the mechanical behavior of a composite laminate from the properties of the ply and the interply. Continuum Damage Mechanics (CDM) formulates intraply damage at the the material constitutive level. Intraply CDM is combined with cohesive elements to model interply damage. A CDM model was developed, implemented, and applied to simple mechanical tests of laminates: low and high velocity impact, tension of coupons, and shear deformation. The analysis of the results and the comparison with experiments indicated that the performance was reasonably good for the impact tests, but insuficient in the other cases. To overcome the limitations of CDM, the kinematics of the discrete finite element approximation was enhanced to include mesh embedded discontinuities, the eXtended Finite Element Method (X-FEM). The X-FEM was adapted to an explicit time integration scheme and was able to reproduce qualitatively the physical failure mechanisms in a composite laminate. However, the results revealed an inconsistency in the formulation that leads to erroneous quantitative results. Finally, the traditional X-FEM was reviewed, and a new method was developed to overcome its limitations, the stable cohesive X-FEM. The properties of the new method were studied in detail, and it was demonstrated that the new method was robust and can be implemented in a explicit finite element formulation, providing a new tool for damage simulation in composite materials.

Güímar and La Orotava mega-landslides (Tenerife) and tsunamis deposits in Canary Islands

More than 20 mega-landslides have been described in the Canary Islands affecting the flanks of the volcanic edifices. Gliimar and La Orotava landslides, in Tenerife, are two exceptional cases due to their huge dimensions and outstanding geomorphological features. The estimated volume of these landslides exceed tens of cubic km. Tsunami deposits have been also identified in some of the islands of the archipelago probably associated to the large landslides of the islands flanks. An investigation has been carried out to explain the causes of these large instability processes and their failure mechanisms. One of the main aspects investigated was the geomechanical characteristics of the volcanic rock masses, specially the hyaloclastite rocks forming the substratum underlying the emerged volcanic building. The low strength and high deformability properties of these rocks have played a fundamental role on the stability of the island flanks. The results have shown the gravitational origin of these instability processes as the main failure mechanism. Volcanic eruptions or large earthquakes could be contributing factors to the instability, but according with the data obtained in Gliimar and La Orotava cases they are not necessary as triggering factors. As a result of the field work carried out in the frame of the project, three large tsunami deposits have been identified in the islands of Lanzarote, Tenerifc and Gran Canaria attributed to rnega-Iandslides, possibly related to Guimar and La Orotava. A Sumrnary of their main features is described.

An online failure prediction system for private IaaS platforms

The size and complexity of cloud environments make them prone to failures. The traditional approach to achieve a high dependability for these systems relies on constant monitoring. However, this method is purely reactive. A more proactive approach is provided by online failure prediction (OFP) techniques. In this paper, we describe a OFP system for private IaaS platforms, currently under development, that combines di_erent types of data input, including monitoring information, event logs, and failure data. In addition, this system operates at both the physical and virtual planes of the cloud, taking into account the relationships between nodes and failure propagation mechanisms that are unique to cloud environments.

Evolution of microstructure, macrotexture and mechanical properties of commercially pure Ti during ECAP-conform processing and drawing

Long-length ultrafine-grained (UFG) Ti rods are produced by equal-channel angular pressing via the conform scheme (ECAP-C) at 200 °C, which is followed by drawing at 200 °C. The evolution of microstructure, macrotexture, and mechanical properties (yield strength, ultimate tensile strength, failure stress, uniform elongation, elongation to failure) of pure Ti during this thermo-mechanical processing is studied. Special attention is also paid to the effect of microstructure on the mechanical behavior of the material after macrolocalization of plastic flow. The number of ECAP-C passes varies in the range of 1–10. The microstructure is more refined with increasing number of ECAP-C passes. Formation of homogeneous microstructure with a grain/subgrain size of 200 nm and its saturation after 6 ECAP-C passes are observed. Strength properties increase with increasing number of ECAP passes and saturate after 6 ECAP-C passes to a yield strength of 973 MPa, an ultimate tensile strength of 1035 MPa, and a true failure stress of 1400 MPa (from 625, 750, and 1150 MPa in the as-received condition). The true strain at failure failure decreases after ECAP-C processing. The reduction of area and true strain to failure values do not decrease after ECAP-C processing. The sample after 6 ECAP-C passes is subjected to drawing at 200¯C resulting in reduction of a grain/subgrain size to 150 nm, formation of (10 1¯0) fiber texture with respect to the rod axis, and further increase of the yield strength up to 1190 MPa, the ultimate tensile strength up to 1230 MPa and the true failure stress up to 1600 MPa. It is demonstrated that UFG CP Ti has low resistance to macrolocalization of plastic deformation and high resistance to crack formation after necking.

Molecular dynamics modeling and simulation of void growth in two dimensions

The mechanisms of growth of a circular void by plastic deformation were studied by means of molecular dynamics in two dimensions (2D). While previous molecular dynamics (MD) simulations in three dimensions (3D) have been limited to small voids (up to ≈10 nm in radius), this strategy allows us to study the behavior of voids of up to 100 nm in radius. MD simulations showed that plastic deformation was triggered by the nucleation of dislocations at the atomic steps of the void surface in the whole range of void sizes studied. The yield stress, defined as stress necessary to nucleate stable dislocations, decreased with temperature, but the void growth rate was not very sensitive to this parameter. Simulations under uniaxial tension, uniaxial deformation and biaxial deformation showed that the void growth rate increased very rapidly with multiaxiality but it did not depend on the initial void radius. These results were compared with previous 3D MD and 2D dislocation dynamics simulations to establish a map of mechanisms and size effects for plastic void growth in crystalline solids.